参数资料
型号: PIC12F683-E/MD
厂商: Microchip Technology
文件页数: 137/176页
文件大小: 0K
描述: IC PIC MCU FLASH 2KX14 8DFN
产品培训模块: Asynchronous Stimulus
Digi-Key 应用说明: AN0005 PWM Example with Microchip's CCP Module
AN0005 Example Code
标准包装: 91
系列: PIC® 12F
核心处理器: PIC
芯体尺寸: 8-位
速度: 20MHz
外围设备: 欠压检测/复位,POR,PWM,WDT
输入/输出数: 5
程序存储器容量: 3.5KB(2K x 14)
程序存储器类型: 闪存
EEPROM 大小: 256 x 8
RAM 容量: 128 x 8
电压 - 电源 (Vcc/Vdd): 2 V ~ 5.5 V
数据转换器: A/D 4x10b
振荡器型: 内部
工作温度: -40°C ~ 125°C
封装/外壳: 8-VDFN 裸露焊盘
包装: 管件
配用: AC164326-ND - MODULA SKT PM3 20QFN
I3-DB12F683-ND - BOARD DAUGHTER ICEPIC3
2007 Microchip Technology Inc.
DS41211D-page 61
PIC12F683
9.0
ANALOG-TO-DIGITAL
CONVERTER (ADC) MODULE
The
Analog-to-Digital
Converter
(ADC)
allows
conversion of an analog input signal to a 10-bit binary
representation of that signal. This device uses analog
inputs, which are multiplexed into a single sample and
hold circuit. The output of the sample and hold is
connected to the input of the converter. The converter
generates a 10-bit binary result via successive
approximation and stores the conversion result into the
ADC result registers (ADRESL and ADRESH).
The ADC voltage reference is software selectable to
either VDD or a voltage applied to the external reference
pins.
The ADC can generate an interrupt upon completion of
a conversion. This interrupt can be used to wake-up the
device from Sleep.
Figure 9-1 shows the block diagram of the ADC.
FIGURE 9-1:
ADC BLOCK DIAGRAM
9.1
ADC Configuration
When configuring and using the ADC the following
functions must be considered:
GPIO configuration
Channel selection
ADC voltage reference selection
ADC conversion clock source
Interrupt control
Results formatting
9.1.1
GPIO CONFIGURATION
The ADC can be used to convert both analog and digital
signals. When converting analog signals, the I/O pin
should be configured for analog by setting the associated
TRIS and ANSEL bits. See the corresponding GPIO
section for more information.
9.1.2
CHANNEL SELECTION
The CHS bits of the ADCON0 register determine which
channel is connected to the sample and hold circuit.
When changing channels, a delay is required before
starting the next conversion. Refer to Section 9.2
“ADC Operation” for more information.
GP0/AN0
A/D
GP1/AN1/VREF
GP2/AN2
VDD
VREF
ADON
GO/DONE
VCFG = 1
VCFG = 0
CHS
ADRESH
ADRESL
10
ADFM
GP4/AN3
0
= Left Justify
1
= Right Justify
Note:
Analog voltages on any pin that is defined
as a digital input may cause the input
buffer to conduct excess current.
相关PDF资料
PDF描述
PIC18LF43K22T-I/MV IC MCU 8BIT 8KB FLASH 40UQFN
V375C48M75BG CONVERTER MOD DC/DC 48V 75W
V375C48M75BF CONVERTER MOD DC/DC 48V 75W
PIC18F43K22T-I/MV IC MCU 8BIT 8KB FLASH 40UQFN
V375C48M75B3 CONVERTER MOD DC/DC 48V 75W
相关代理商/技术参数
参数描述
PIC12F683-I/MD 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 6I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC12F683-I/MDQTP 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8-Pin Flash-Based, 8-Bit CMOS Microcontrollers with nanoWatt Technology
PIC12F683-I/MF 功能描述:8位微控制器 -MCU 3.5KB 128 RAM 6 I/O RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
PIC12F683-I/MF 制造商:Microchip Technology Inc 功能描述:8BIT FLASH MCU SMD 12F683 DFN-8
PIC12F683-I/MFQTP 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:8-Pin Flash-Based, 8-Bit CMOS Microcontrollers with nanoWatt Technology