- 您现在的位置：买卖IC网 > PDF目录270896 > S75PL127JCDBFWB0 (Spansion Inc.) Power supply woltage of 2.7 to 3.1 volt PDF资料下载
参数资料
| 型号： | S75PL127JCDBFWB0 |
| 厂商： | Spansion Inc. |
| 英文描述： | Power supply woltage of 2.7 to 3.1 volt |
| 中文描述： | 功率2月7号至三月一日伏的电源woltage |
| 文件页数： | 20/183页 |
| 文件大小： | 4247K |
| 代理商： | S75PL127JCDBFWB0 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页第175页第176页第177页第178页第179页第180页第181页第182页第183页
December 15, 2004 S29GLxxxN_MCP_A1
S29GLxxxN MirrorBitTM Flash Family
117
Advance
Informatio n
“unfreeze state” is to go through a power cycle, or hardware reset. The Software
Reset command will not clear the PPB Lock Bit to the “unfreeze state”. System
boot code can determine if any changes to the PPB bits are needed e.g. to allow
new system code to be downloaded. If no changes are needed then the boot code
can set the PPB Lock Bit to disable any further changes to the PPB bits during
system operation.
The WP# write protect pin adds a final level of hardware protection. When this
pin is low it is not possible to change the contents of the WP# protected sectors.
These sectors generally hold system boot code. So, the WP# pin can prevent any
changes to the boot code that could override the choices made while setting up
sector protection during system initialization.
It is possible to have sectors that have been persistently locked, and sectors that
are left in the dynamic state. The sectors in the dynamic state are all unprotected.
If there is a need to protect some of them, a simple DYB Set command sequence
is all that is necessary. The DYB Set and DYB Clear commands for the dynamic
sectors switch the DYB bits to signify protected and unprotected, respectively. If
there is a need to change the status of the persistently locked sectors, a few more
steps are required. First, the PPB Lock Bit must be disabled to the “unfreeze
state” by either putting the device through a power-cycle, or hardware reset. The
PPB bits can then be changed to reflect the desired settings. Setting the PPB Lock
Bit once again to the “freeze state” will lock the PPB bits, and the device operates
normally again.
Note: to achieve the best protection, it's recommended to execute the PPB Lock
Bit Set command early in the boot code, and protect the boot code by holding
WP# = VIL.
Persistent Protection Bit (PPB)
A single Persistent (non-volatile) Protection Bit is assigned to each sector. If a PPB
is programmed to the protected state through the “PPB Program” command, that
sector will be protected from program or erase operations will be read-only. If a
PPB requires erasure, all of the sector PPB bits must first be erased in parallel
through the “All PPB Erase” command. The “All PPB Erase” command will prepro-
grammed all PPB bits prior to PPB erasing. All PPB bits erase in parallel, unlike
programming where individual PPB bits are programmable. The PPB bits have the
same endurance as the flash memory.
Programming the PPB bit requires the typical word programming time without uti-
lizing the Write Buffer. During a PPB bit programming and A11 PPB bit erasing
sequence execution, the DQ6 Toggle Bit I will toggle until the programming of the
PPB bit or erasing of all PPB bits has completed to indicate programming and
erasing status. Erasing all of the PPB bits at once requires typical sector erase
time. During the erasing of all PPB bits, the DQ3 Sector Erase Timer bit will output
a 1 to indicate the erasure of all PPB bits are in progress. When the erasure of all
PPB bits has completed, the DQ3 Sector Erase Timer bit will output a 0 to indicate
that all PPB bits have been erased. Reading the PPB Status bit requires the initial
access time of the device.
Persistent Protection Bit Lock (PPB Lock Bit)
A global volatile bit. When set to the “freeze state”, the PPB bits cannot be
changed. When cleared to the “unfreeze state”, the PPB bits are changeable.
There is only one PPB Lock Bit per device. The PPB Lock Bit is cleared to the “un-
相关PDF资料 |
PDF描述 |
|---|---|
| S75PL127JCDBFWB2 | Power supply woltage of 2.7 to 3.1 volt |
| S75PL127JCEBFWB2 | Power supply woltage of 2.7 to 3.1 volt |
| S75PL127JCDBFWB3 | Power supply woltage of 2.7 to 3.1 volt |
| S75PL127JCEBFWB3 | Power supply woltage of 2.7 to 3.1 volt |
| S29CD016G0PFAN010 | 16 Megabit (512 K x 32-Bit) CMOS 2.5 Volt-only Burst Mode, Dual Boot, Simultaneous Read/Write Flash Memory |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S75PL127JCDBFWB2 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:Power supply woltage of 2.7 to 3.1 volt |
| S75PL127JCDBFWB3 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:Power supply woltage of 2.7 to 3.1 volt |
| S75PL127JCDBFWU0 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:Power supply woltage of 2.7 to 3.1 volt |
| S75PL127JCDBFWU2 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:Power supply woltage of 2.7 to 3.1 volt |
| S75PL127JCDBFWU3 | 制造商:SPANSION 制造商全称:SPANSION 功能描述:Power supply woltage of 2.7 to 3.1 volt |
发布紧急采购，3分钟左右您将得到回复。