- 您现在的位置：买卖IC网 > PDF目录11815 > SC28C94A1N,112 (NXP Semiconductors)IC UART QUAD W/FIFO 48-DIP PDF资料下载
参数资料
| 型号： | SC28C94A1N,112 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 15/39页 |
| 文件大小： | 0K |
| 描述： | IC UART QUAD W/FIFO 48-DIP |
| 标准包装： | 7 |
| 特点： | 故障启动位检测 |
| 通道数： | 4，QUART |
| FIFO's： | 8 字节 |
| 电源电压： | 5V |
| 带自动流量控制功能： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 通孔 |
| 封装/外壳： | 48-DIP（0.600"，15.24mm） |
| 供应商设备封装： | 48-DIP |
| 包装： | 管件 |
| 其它名称： | 568-1115-5 935262535112 SC28C94A1N |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
Philips Semiconductors
Product data sheet
SC28C94
Quad universal asynchronous receiver/transmitter (QUART)
2006 Aug 09
22
I/O Port Control Channel B (IOPCRB)
IOPCR[xx]
IOPCRb[7:6]
IOPCRb[5:4]
IOPCRb[3:2]
IOPCRb[1:0]
Pin Control Bits
I/O3B
I/O2B
I/O1B
I/O0B
00 = input
IPR(7), TxC in
IPR(6), RxC in
IPR(3), TxC in
IPR(2), CTSN
01 = output
OPRab(7)
OPRab(6)
RTSN1 if IOPCR[5:4] = 01
OPRab(3)
RTSN2 if IOPCR[5:4]
≠ 01
OPRab(2)
10 = output
TxC 16x
RxC 1x
C/T ab out
TxC 1x
11 = output
TxC 1x
RxC 16x
RxC 1x
TxC 16x
I/O Port Control Channel C (IOPCRC)
IOPCR[xx]
IOPCRc[7:6]
IOPCRc[5:4]
IOPCRc[3:2]
IOPCRc[1:0]
Pin Control Bits
I/O3C
I/O2C
I/O1C
I/O0C
00 = input
IPR(5), TxC in
IPR(4), RxC in
IPR(1), C/Tcd Clk in1 TxC in
IPR(0), CTSN
01 = output
OPRcd(5)
OPRcd(4)
RTSN1 if IOPCR[5:4] = 01
OPRab(1)
RTSN2 if IOPCR[5:4]
≠ 01
OPRcd(0)
10 = output
TxC 16x
RxC 1x
RxC 16x
TxC 1x
11 = output
TxC 1x
RxC 16x
RxC 1x
TxC 16x
I/O Port Control Channel D (IOPCRD)
IOPCR[xx]
IOPCRd[7:6]
IOPCRd[5:4]
IOPCRd[3:2]
IOPCRd[1:0]
Pin Control Bits
I/O3D
I/O2D
I/O1D
I/O0D
00 = input
IPR(7), TxC in
IPR(6), RxC in
IPR(3), TxC in
IPR(2), CTSN
01 = output
OPRcd(7)
OPRcd(6)
RTSN1 if IOPCR[5:4] = 01
OPRcd(3)
RTSN2 if IOPCR[5:4]
≠ 01
OPRcd(2)
10 = output
TxC 16x
RxC 1x
C/T cd out
TxC 1x
11 = output
TxC 1x
RxC 16x
RxC 1x
TxC 16x
The input part of the I/O pins is always active. The programming of the IOPCR bits to 00 merely turns off the out drivers and places
the pin at high impedance.
A read of the IPR register returns the value of the IPR bits as shown above. IPR(5) is at bit position 5 of the data bus. Note that the IPR bit
positions do not follow the 0, 1, 2, 3 order of the I/O ports. During a read of the IPR the I/O ports are not latched. Therefore, it is possible to see
changing data during the read. Port pins that have clocks on them may not yield valid data during the read.
Since the input circuits of the I/O ports are always active it is possible to direct the port signal back into the port. For example: I/O1 will output
the RTS signal. Setting the Counter/Timer (C/T) to be clocked by the I/O1 port will result in the counter counting the number of times RTS goes
active. The change of state detectors on I/O0 and I/O1 will, when programmed, always be sensitive to the signal on the port regardless of the
source of that port’s signal.
NOTES:
1. Normal configurations place RTSN output on I/O1 and place Tx external clock input on I/O3. For the 48 pin Dual In-Line package, I/O3 is
not available. The following options allow flexible I/O programming with the 48 pin package:
When IOPCR(7:6), the I/O3 control,
≠ 00, then I/O1 becomes available to the transmitter as an external clock.
When IOPCR(5:4), the I/O2 control, = 01, then I/O2 may be the RTSN signal if MR1(7) = 1 and OPR(4) = 1.
2. I/O1 becomes RTSN when IOPCR(3:2) = 01 and MR1(7) = 1 and OPR(1) = 1. (OPR(3) for channel B)
3. Recommended method for setting RTS/CTS flow control is to set IPCR [5:4] to 01 and to set I/OPCR[1:0] to 00. This makes I/O[2} RTSN
and I/O[1] CTSN. Caution: When RTS/CTS is active writing to the OPR register could conflict with the receiver control of OPR [6] and
OPR [4].
相关PDF资料 |
PDF描述 |
|---|---|
| V24C24H150B | CONVERTER MOD DC/DC 24V 150W |
| SC16C554DIA68,512 | IC UART QUAD W/FIFO 68-PLCC |
| AT32UC3L064-D3HR | MCU AVR32 64K FLASH 48TTLGA |
| ST16C550CP40 | IC UART FIFO 16BYTE 40PDIP |
| V24B24H150BG3 | CONVERTER MOD DC/DC 24V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC28L194 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Quad UART for 3.3V and 5V supply voltage |
| SC28L194A1A | 功能描述:UART 接口集成电路 3V-5V 4CH UART INTEL/MOT INTRF RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC28L194A1A,512 | 功能描述:UART 接口集成电路 3V-5V 4CH UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC28L194A1A,518 | 功能描述:UART 接口集成电路 3V-5V 4CH UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC28L194A1A,529 | 功能描述:UART 接口集成电路 3V-5V 4CH UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。