- 您现在的位置：买卖IC网 > PDF目录11815 > SC28C94A1N,112 (NXP Semiconductors)IC UART QUAD W/FIFO 48-DIP PDF资料下载
参数资料
| 型号： | SC28C94A1N,112 |
| 厂商： | NXP Semiconductors |
| 文件页数： | 7/39页 |
| 文件大小： | 0K |
| 描述： | IC UART QUAD W/FIFO 48-DIP |
| 标准包装： | 7 |
| 特点： | 故障启动位检测 |
| 通道数： | 4，QUART |
| FIFO's： | 8 字节 |
| 电源电压： | 5V |
| 带自动流量控制功能： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 通孔 |
| 封装/外壳： | 48-DIP（0.600"，15.24mm） |
| 供应商设备封装： | 48-DIP |
| 包装： | 管件 |
| 其它名称： | 568-1115-5 935262535112 SC28C94A1N |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
Philips Semiconductors
Product data sheet
SC28C94
Quad universal asynchronous receiver/transmitter (QUART)
2006 Aug 09
15
Mode Registers 0, 1 and 2
The addressing of the Mode Registers is controlled by the MR
Register pointer. On any access to the Mode Registers this pointer
is always incremented. Upon reaching a value of 2 it remains at 2
until changed by a CR command or a hardware reset.
MR0 – Mode Register 0
Mode Register 0 (MR0) is part of the UART configuration registers.
It controls the watch dog timer and the encoding of the number of
characters received in the RxFIFO. The lower four bits of this
register are not implemented in the hardware of the chip. MR0 is
normally set to either 80h or 00h. A read of this register will return
1111 (Fh) in the lower four bits.
The MR0 register is accessed by setting the MR Pointer to zero (0)
via the command register command 1011 (Bh).
MR0[7]: This bit enables or disables the RxFIFO watch dog timer.
MR0[7] = 1 enable watchdog timer
MR0[7] = 0 disable watchdog timer
MR0[6:4]: These bits are normally set to 0 except as noted in the
“Interrupt Threshold Calculation” description.
MR0[3:0]: These bits are not implemented in the chip. These bits
should be be considered “reserved.”
MR1 – Mode Register 1
MR1 is accessed when the MR pointer points to MR1. The pointer is
set to MR1 by RESET, a set pointer command applied via the CR or
after an access to MR0. After reading or writing MR1, the pointers
are set at MR2.
MR1[7] – Receiver Request-to-Send Flow Control
This bit controls the deactivation of the RTSN output (I/O2x) by the
receiver. This output is manually asserted and negated by
commands applied via the command register. MR1[7] = 1 causes
RTSN to be automatically negated upon receipt of a valid start bit if
the receiver FIFO is full. RTSN is re-asserted when an empty FIFO
position is available. This feature can be used to prevent overrun in
the receiver by using the RTSN output signal to control the CTS
input (the QUART I/O0 pin) of the transmitting device.
Use of this feature requires the I/O2 pin to be programmed as output
via the I/OPCR and to be driving a 0 via the OPR. When the RxFIFO
is full and the start bit of the ninth character is sensed the receiver
logic will drive the I/O2 pin high. This pin will return low when
another RxFIFO position is vacant.
MR1[6] – Receiver Interrupt Select 1
This bit is normally set to 0 except as noted in the “Interrupt
Threshold Calculation” description. MR1[6] operates with MR0[6] to
prevent the receiver from bidding until a particular fill level is
attained. For software compatibility this bit is designed to emulate
the RxFIFO interrupt function of previous Philips Semiconductors
UARTs.
MR1[5] – Error Mode Select
This bit selects the operating mode of the three FIFOed status bits
(received break, FE, PE). In the character mode, status is provided
on a character-by-character basis; the status applies only to the
character at the top of the FIFO.
In the block mode, the status provided in the SR for these bits is the
accumulation (logical-OR) of the status for all characters coming to
the top of the FIFO since the last reset error command was issued.
In the “Block Error” mode the ORing of the error status bits and the
presentation of them to the status register takes place as the bytes
enter the RxFIFO. This allows an indication of problem data when
the error occurs after the leading bytes have been received. In the
character mode the error bits are presented to the status register
when the corresponding byte is at the top of the FIFO.
MR1[4:3] – Parity Mode Select
If “with parity” or “force parity” is selected, a parity bit is added to the
transmitted character and the receiver performs a parity check on
incoming data. MR1[4:3] = 11 selects the channel to operate in the
special wake-up mode (see ‘Wake-Up Mode’).
MR1[2] – Parity Type Select
This bit selects the parity type (odd or even) if the “with parity” mode
is programmed by MR1[4:3], and the polarity of the forced parity bit
if the “force parity” mode is programmed. It has no effect if the “no
parity” mode is programmed. In the special “wake-up” mode, it
selects the polarity of the transmitted A/D bit.
MR1[1:0] – Bits per Character Select
This field selects the number of data bits per character to be
transmitted and received. The character length does not include the
start, parity, and stop bits.
MR2 – Mode Register 2
MR2 is accessed when the channel MR pointer points to MR2,
which occurs after any access to MR1. Accesses to MR2 do not
change the pointer.
MR2[7:6] – Mode Select
The QUART can operate in one of four modes. MR2[7:6] = 00 is the
normal mode, with the transmitter and receiver operating
independently. MR2[7:6] = 01 places the channel in the automatic
echo mode, which automatically re-transmits the received data. The
following conditions are true while in automatic echo mode:
1. Received data is re-clocked and retransmitted on the TxD
output.
2. The receive clock is used for the transmitter.
3. The receiver must be enabled, but the transmitter need not be
enabled.
4. The TxRDY and TxEMT status bits are inactive.
5. The received parity is checked, but is not regenerated for
transmission, i.e., transmitted parity bit is as received.
Two diagnostic modes can also be selected. MR2[7:6] = 10 selects
local loopback mode. In this mode:
1. The transmitter output is internally connected to the receiver
input.
2. The transmit clock is used for the receiver.
3. The TxD output is held high.
4. The RxD input is ignored.
5. The transmitter must be enabled, but the receiver need not be
enabled.
6. CPU to transmitter and receiver communications continue normally.
The second diagnostic mode is the remote loopback mode, selected
by MR2[7:6] = 11. In this mode:
1. Received data is re-clocked and retransmitted on the TxD output.
2. The receive clock is used for the transmitter.
3. Received data is not sent to the local CPU, and the error status
conditions are inactive.
4. The received parity is not checked and is not regenerated for trans-
mission, i.e., the transmitted parity bit is as received.
5. The receiver must be enabled, but the transmitter need not be enabled.
6. Character framing is not checked, and the stop bits are retrans-
mitted as received.
7. A received break is echoed as received until the next valid start bit
is detected.
相关PDF资料 |
PDF描述 |
|---|---|
| V24C24H150B | CONVERTER MOD DC/DC 24V 150W |
| SC16C554DIA68,512 | IC UART QUAD W/FIFO 68-PLCC |
| AT32UC3L064-D3HR | MCU AVR32 64K FLASH 48TTLGA |
| ST16C550CP40 | IC UART FIFO 16BYTE 40PDIP |
| V24B24H150BG3 | CONVERTER MOD DC/DC 24V 150W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SC28L194 | 制造商:PHILIPS 制造商全称:NXP Semiconductors 功能描述:Quad UART for 3.3V and 5V supply voltage |
| SC28L194A1A | 功能描述:UART 接口集成电路 3V-5V 4CH UART INTEL/MOT INTRF RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC28L194A1A,512 | 功能描述:UART 接口集成电路 3V-5V 4CH UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC28L194A1A,518 | 功能描述:UART 接口集成电路 3V-5V 4CH UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| SC28L194A1A,529 | 功能描述:UART 接口集成电路 3V-5V 4CH UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。