- 您现在的位置：买卖IC网 > PDF目录98079 > SCANPSC100FDMQB (NATIONAL SEMICONDUCTOR CORP) SPECIALTY MICROPROCESSOR CIRCUIT, CDIP28 PDF资料下载
参数资料
| 型号： | SCANPSC100FDMQB |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | SPECIALTY MICROPROCESSOR CIRCUIT, CDIP28 |
| 封装： | CERAMIC, DIP-28 |
| 文件页数： | 2/27页 |
| 文件大小： | 381K |
| 代理商： | SCANPSC100FDMQB |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
READ AND WRITE CYCLES
(Continued)
number of processor generated wait states. For example, if
the TDO shifter/buffer is not enabled for shift operations and
the processor writes to the TDO shifter/buffer address 3
times, the two registers which make up the TDO shifter/
buffer will accept the first two bytes of data, but since the
data is not shifting out, the 3rd byte will be held off by the
RDY signal indefinitely. An equally severe problem could
result with a finite number of wait states if the application
uses dynamic memories. Holding the local bus with the
PSC100F RDY line long enough to violate a DRAM refresh
time will result in lost data within the dynamic memory.
Writing and Reading without the use of RDY : With use of
worst case PSC100F timing, Write and Read cycles can be
successfully completed without the use of the RDY signal. All
read and write cycles will complete within 2.5 SCK cycles
(worst case). Therefore, by assuring at least 2.5 cycles occur
after the rising edge of STB, bus cycles can be completed
without using the RDY “handshake”. The critical timing rela-
tionship within the PSC100F for write and read operation is
between the rising edge of STB and the falling edge of SCK.
The rising edge of strobe latches the address/data and also
generates the internal signals required to complete read/
write within the PSC100F (including a signal with resets the
read/write logic and releases the RDY line). The propagation
of these internal signals is initiated on the first falling edge of
SCK after the STB pin is asserted high. If the rising edge on
STB occurs an internal setup time (t
s4) or greater before the
falling edge of SCK, the bus cycle can be completed within
1.5 SCK cycles (see
Figure 4). However, if the internal setup
time is not met, the propagation of internal control/reset
signals is delayed until the next falling edge of SCK (1 SCK
cycle later) which effectively completes the read/write opera-
tion and reset the logic for the next bus cycle within 2.5
cycles (see
Figure 5). Synchronizing the rising edge of STB
with the falling edge of SCK to assure that t
s4 is met provides
the maximum performance for a read/write operation. How-
ever, the asynchronous interface can be used effectively with
software delays, hardware delays or programmed wait
states (to assure 2.5 SCK cycles are completed) to avoid the
need for synchronization.
Consecutive Reads and Writes: Separate control logic and
data/address latches are used for a read and write operation
within the PSC100F. This allows a write to occur after a read
(or conversely, a read to occur after a write) prior to the
1.5/2.5 SCK clock cycle requirements described above. The
timing for a read (or write) followed by a write (or read) is
shown in
SYNCHRONIZATION
Writes and reads can be synchronized by using any of three
methods: polling, interrupts, or wait state generation:
Status bits may be polled to see if a register is ready to be
written to or read from. To stabilize the status bits for read
operations, the Update Status bit must be set in MODE2
to latch the status.
Note: The status bits only provide the state of the shifter/buffers and do not
indicate that an internal write or read is complete. Therefore, for
applications not using the RDY signal to monitor the internal write/read
status, timing must be controlled to assure that at least 2.5 SCK cycles
are completed between consecutive read or consecutive write cycles.
Any of three different events can be used to generate
interrupts by forcing the INT pin high, see
The RDY pin can be used to hold off the host until the
addressed register is ready to be accessed. As described
above, this pin can also be used to hold off additional
reads/writes until the synchronizer has recovered from
the previous read/write. RDY = 0 signifies that the
’PSC100F is ready to complete the current PPI cycle.
The logic that determines the state of RDY is summa-
rized in
Reading from CNT32 can be synchronized for testing by
using the Single Step Counter mode bit.
TABLE 1. Interrupt Logic
MODE1(7) = 1 and TDO
MODE1(6) = 1 and TDI
MODE1(5) = 1 and
Shifter/Buffer Not Full
Shifter/Buffer Not Empty
CNT32 Not Loaded, or at
INT
Terminal Count
1X
X
1
X1X
1
XX
1
000
0
Note 6: Interrupts are generated using the INT pin. Three events trigger INT high. Each event has its own mode bit associated with it for masking or enabling these
interrupts.
SCANPSC100F
Embedded
www.national.com
10
相关PDF资料 |
PDF描述 |
|---|---|
| SCANPSC100FLMQB | SPECIALTY MICROPROCESSOR CIRCUIT, CQCC28 |
| SCB68172C2F28 | VME BUS CONTROLLER, CDIP28 |
| SCC2691AC1D24 | 1 CHANNEL(S), 38.4K bps, SERIAL COMM CONTROLLER, PDSO24 |
| SCC2691AE1A28 | 1 CHANNEL(S), 38.4K bps, SERIAL COMM CONTROLLER, PQCC28 |
| SCC2692AC1A44-T | 2 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, PQCC44 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SCANPSC100FLMQB | 制造商:Texas Instruments 功能描述: |
| SCANPSC100FSC | 功能描述:接口 - 专用 Emb Boun Scan Cont RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| SCANPSC100FSCX | 功能描述:接口 - 专用 Emb Boun Scan Cont RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| SCANPSC110 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:SCAN Bridge Hierarchical and Multidrop Addressable JTAG Port (IEEE1149.1 System Test Support) |
| SCANPSC110_ZFC3026B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。