- 您现在的位置：买卖IC网 > PDF目录98079 > SCANPSC100FDMQB (NATIONAL SEMICONDUCTOR CORP) SPECIALTY MICROPROCESSOR CIRCUIT, CDIP28 PDF资料下载
参数资料
| 型号： | SCANPSC100FDMQB |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | SPECIALTY MICROPROCESSOR CIRCUIT, CDIP28 |
| 封装： | CERAMIC, DIP-28 |
| 文件页数： | 23/27页 |
| 文件大小： | 381K |
| 代理商： | SCANPSC100FDMQB |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页
Mode and Status Registers (Continued)
Bit 4: This bit enables the TMS0 shifter/buffer for shift operations. If this bit is set, the TMS0 shifter/buffer will cause TCK to stop
if it is empty.
Bit 3: This bit enables the TMS1 shifter/buffer for shift operations. If this bit is set, the TMS1 shifter/buffer will cause TCK to stop
if it is empty.
Bit 2: This bit is reserved and should remain as a logic 0 during all ’PSC100 operations.
Bit 1: If this bit is set, TMS will be forced high when the 32-bit counter is at state (00000001)h.
Bit 0: This bit causes TDI to be connected directly back through TDO for Loop-Around operations.
MODE REGISTER 1 (MODE1)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
TDO
TDI
CNT32
PRPG
SSC
Freeze
Test
Interrupt
Interrrupt
Interrupt
Enable
Pin
Loop-
Enable
Back
This register is purely a mode register. All bits are writeable and readable. The value 00000000 is placed in this register upon RST
low or a synchronous reset operation.
Bit 7:
If this bit is set and the TDO shifter/buffer is not full (i.e., one or both 8-bit TDO FIFOs are empty), the INT pin will
go high.
Bit 6:
If this bit is set and the TDI shifter/buffer is not empty (i.e., one or both 8-bit TDI FIFOs are full), the INT pin will
go high.
Bit 5:
If this bit is set, and the 32-bit counter is not loaded or has reached terminal count, the INT pin will go high.
Bit 4:
This bit signifies that the TD0 shifter/buffer is reconfigured as a 32-Bit Pseudo Random Pattern Generator. If set,
and MODE0 Bit 7 is set, the TDO shifter/buffer will stop TCK until a seed value has been written to all four of the
8-bit LFSR segments.
Bit 3:
This bit signifies that the TD1 shifter/buffer is reconfigured as a 16-Bit Serial Signature Compactor. If set, and
MODE0 Bit 6 is set, the TDI shifter/buffer will cause TCK to stop until a seed value has been written to the two
TDI registers.
Bit 2:
If this bit is set, a high value on FRZ will force TCK high (see TCK Control Section).
Bits 1 and 0: These bits are used to control Test Loop-Back operations according to the following table.
MODE1
Function
Bit 1
Bit 0
0
Normal Operation
0
1
Loop-Back TDO to TDI
MODE1
Function
Bit 1
Bit 0
1
0
Loop-Back TMS0 to TDI
1
Loop Back TMS1 to TDI
MODE REGISTER 2 (MODE2)
Write:
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Not
Continuous
Update
Single
Used
Update
Status
Reset
Step
CNT32
Read:
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
TDO
TDI
CNT32
TMS0
TMS1
Continuous
Single
Status
Update
Reset
Step
CNT32
This register contains both mode and status bits. Bits 4–7 are status bits only. Bit 3 is a status bit during read operations and a
mode bit during write operations. Bits 0–2 are mode bits only. Upon RST low, or a synchronous reset, the value placed in MODE2
is 10111000 (Read mode). Latches used to update status bits 3–7 retain their last state upon RST and are in an “unknown” state
after power-up. To initialize the latches to a known state, they need to be updated using the Update Status bit (bit 2) or continuous
update bit (bit 3).
Bit 7: Set high if the TDO shifter/buffer is not full, i.e., one or both 8-bit TDO FIFOs are ready to be written to.
Bit 6: Set high if the TDI shifter/buffer is not empty, i.e., one or both 8-bit TDI FIFOs are ready to be read from.
SCANPSC100F
Embedded
www.national.com
5
相关PDF资料 |
PDF描述 |
|---|---|
| SCANPSC100FLMQB | SPECIALTY MICROPROCESSOR CIRCUIT, CQCC28 |
| SCB68172C2F28 | VME BUS CONTROLLER, CDIP28 |
| SCC2691AC1D24 | 1 CHANNEL(S), 38.4K bps, SERIAL COMM CONTROLLER, PDSO24 |
| SCC2691AE1A28 | 1 CHANNEL(S), 38.4K bps, SERIAL COMM CONTROLLER, PQCC28 |
| SCC2692AC1A44-T | 2 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, PQCC44 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SCANPSC100FLMQB | 制造商:Texas Instruments 功能描述: |
| SCANPSC100FSC | 功能描述:接口 - 专用 Emb Boun Scan Cont RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| SCANPSC100FSCX | 功能描述:接口 - 专用 Emb Boun Scan Cont RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| SCANPSC110 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:SCAN Bridge Hierarchical and Multidrop Addressable JTAG Port (IEEE1149.1 System Test Support) |
| SCANPSC110_ZFC3026B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。