- 您现在的位置：买卖IC网 > PDF目录10908 > SI3015-F-FS (Silicon Laboratories Inc)IC ISOMODEM LINE-SIDE DAA 16SOIC PDF资料下载
参数资料
| 型号： | SI3015-F-FS |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 19/94页 |
| 文件大小： | 0K |
| 描述： | IC ISOMODEM LINE-SIDE DAA 16SOIC |
| 标准包装： | 48 |
| 系列： | ISOmodem® |
| 数据格式： | V.90 |
| 波特率： | 2.4k |
| 电源电压： | 3.3V，5V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC N |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页
Si2400
26
Rev. 1.3
5.13.2. Modem in slave mode
Configure GPIO4 as ALERT (S2E[7:6] [GPIO4] = 11b).
The Si2400 performs a reverse turnaround when it
detects a carrier drop longer than 20 ms. The Si2400
then reverses (it changes its carrier from 1300 Hz to
390 Hz) and waits to detect a 1300 Hz carrier for
220 ms. If the Si2400 detects more than 40 ms of a
1300 Hz carrier in a time window of 220 ms, then it will
set the ALERT pin (GPIO4) and the next character
echoed by the Si2400 will be a “v”.
If the Si2400 does not detect more than 40 ms of the
1300 Hz carrier in a time window of 220 ms, then it
reverses again and waits to detect a 390 Hz carrier for
220 ms. Then, if the Si2400 detects more than 40 ms of
a 390 Hz carrier in a time window of 220 ms, it will set
the ALERT pin (GPIO4) and the next character echoed
by the Si2400 will be a “c”.
At this point, if the Si2400 does not detect more than
40 ms of the 390 Hz carrier in a time window of 220 ms,
then it will hang up, set the ALERT pin (GPIO4), and the
next character echoed by the Si2400 will be an “N” (no
carrier).
Successful completion of a turnaround procedure in
either
master
or
slave
will
automatically
update
S07[4] (V23T) and S07[5] (V23R) to indicate the new
status of the V.23 connection.
In order to avoid using the ALERT pin, the host may
also be notified of the ALERT condition by using 9-bit
data
mode.
Setting
S15[0] (NBE) = 1b
and
S0C[3] (9BF) = 0b will configure the ninth bit on the
Si2400 TXD path to function exactly as the ALERT pin
has been described.
5.14. V.42 HDLC Mode
The Si2400 supports V.42 through hardware HDLC
framing in all modem data modes. Frame packing and
unpacking,
including
opening
and
closing
flag
generation
and
detection,
CRC
computation
and
checking, zero insertion and deletion, and modem data
transmission and reception are all performed by the
Si2400.
V.42
error
correction
and
V.42bis
data
compression must be performed by the host.
The digital link interface in this mode uses the same
UART interface (8-Bit Data and 9-Bit Data formats) as in
the asynchronous modes and the ninth data bit may be
used as an escape by setting S15[0] (NBE) = 1b. When
using HDLC in 9-Bit Data mode, if the ninth bit is not
used as an escape, it is ignored.
To use the HDLC feature on the Si2400, the host must
first
enable
HDLC
operation
by
setting
S07[7] (HDEN) = 1b. Next, the host may initiate the call
or answer the call using either the “ATDT#”, the “ATA”
command, or the auto-answer mode. (The auto-answer
mode is implemented by setting register S00 (NR) to a
non-zero value.) When the call is connected, a “c”, “d”,
or a “v” is echoed to the host controller. The host may
now send/receive data across the UART using either
the 8-Bit Data or 9-Bit Data formats with flow control.
At this point, the Si2400 will begin framing data into the
HDLC format. On the transmit side, if no data is
available from the host, the HDLC flag pattern is sent
repeatedly.
When
data
is
available,
the
Si2400
computes the CRC code throughout the frame and the
data is sent with the HDLC zero-bit insertion algorithm.
HDLC flow control operates in a similar manner to
normal asynchronous flow control across the UART and
is shown in Figure 11. In order to operate flow control
(using the CTS pin to indicate when the Si2400 is ready
to accept a character), a DTE rate higher than the line
rate should be selected. The method of transmitting
HDLC frames is as follows:
1. After the call is connected, the host should begin sending
the frame data to the Si2400, using the CTS flow control to
ensure data synchronicity. A 1-deep character FIFO is
implemented in the Si2400 to ensure that data is always
available to transmit.
2. When the frame is complete, the host should simply stop
sending data to the Si2400. As shown in Figure 11B, since
the Si2400 does not yet recognize the end-of-frame, it will
expect an extra byte and assert CTS. If CTS is used to
cause a host interrupt, then this final interrupt should be
ignored by the host.
3. When the Si2400 is ready to send the next byte, if it has
not yet received any data from the host, it will recognize
this as an end-of-frame, raise CTS, calculate the final CRC
code, transmit the code, and begin transmitting stop flags.
4. After transmitting the first stop flag, the Si2400 will lower
CTS indicating that it is ready to receive the next frame
from the host. At this point the process repeats as in
step 1.
The method of receiving HDLC frames is as follows:
1. After the call is connected, the Si2400 searches for flag
data. Then, once the first non-flag word is detected, the
CRC is continuously computed, and the data is sent
across the UART (8-Bit Data or 9-Bit Data mode) to the
host after removing the HDLC zero-bit insertion. The DTE
rate of the host must be at least as high as that of data
transmission. HDLC mode only works with 8-bit data
words; the ninth bit is used only for escape on TXD and
End-of-Frame Received (EOFR) on RXD.
2. When the Si2400 detects the stop flag, it will send the last
data word in the frame as well as the two CRC bytes and
determine if the CRC checksum matches. Thus, the last
two bytes are not frame data, but are the CRC bytes,
which can be discarded by the host. If the checksum
matches, then the Si2400 echoes “G” (good). If the
相关PDF资料 |
PDF描述 |
|---|---|
| SI3050-E1-FM | IC VOICE DAA SYSTEM SIDE 24QFN |
| JBXEA2G07FSSDS | CONN RCPT 7POS DOUBLE NUT SOLDER |
| VE-J6V-IY-B1 | CONVERTER MOD DC/DC 5.8V 50W |
| VE-J6T-IY-B1 | CONVERTER MOD DC/DC 6.5V 50W |
| VE-2NX-IX-F1 | CONVERTER MOD DC/DC 5.2V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI3015-F-FSR | 制造商:Silicon Laboratories Inc 功能描述:Modem Chip Chipset 2.4Kbps 16-Pin SOIC T/R 制造商:Silicon Laboratories Inc 功能描述:MODEM CHIP CHIPSET ISOMODEM 2.4KBPS 16SOIC - Tape and Reel 制造商:Silicon Laboratories 功能描述:Modem Chip Chipset 2.4Kbps 16-Pin SOIC T/R |
| SI3015-FS | 功能描述:IC ISOMODEM LINE-SIDE DAA 16SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 调制解调器 - IC 和模块 系列:ISOmodem® 标准包装:25 系列:- 数据格式:V.21，V.22，V.23，V.29，V.32，V.34，V.90，V.92，Bell 103，Bell 212A 波特率:33.6k 电源电压:3.3V 安装类型:- 封装/外壳:- 供应商设备封装:- 包装:托盘 配用:591-1013-ND - KIT DEV SOCKETMODEM PARALLEL591-1009-ND - KIT DEV SRL SOCKETMODEM UNIVERSL 其它名称:MT5656SMI-P-V-34.R2-SPMT5656SMI-P-V-34.R2-SP-NDQ4711574 |
| SI3015-FSR | 制造商:Silicon Laboratories Inc 功能描述:SI2403 ISOMODEM LINE-SIDE LEAD-FREE SOIC 0 TO 70 DEG. C - Tape and Reel |
| SI3015-KS | 功能描述:电信线路管理 IC SI2400 Line Side RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI3015-KSR | 功能描述:电信线路管理 IC SI2400 Line Side RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。