- 您现在的位置：买卖IC网 > PDF目录10908 > SI3015-F-FS (Silicon Laboratories Inc)IC ISOMODEM LINE-SIDE DAA 16SOIC PDF资料下载
参数资料
| 型号： | SI3015-F-FS |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 35/94页 |
| 文件大小： | 0K |
| 描述： | IC ISOMODEM LINE-SIDE DAA 16SOIC |
| 标准包装： | 48 |
| 系列： | ISOmodem® |
| 数据格式： | V.90 |
| 波特率： | 2.4k |
| 电源电压： | 3.3V，5V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC N |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页当前第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页
Si2400
40
Rev. 1.3
7. Low Level DSP Control
Although not necessary for most applications, the DSP
low-level control functions are available for users with
very specific applications requiring direct DSP control.
7.1. DSP Registers
Several DSP registers are accessible through the
Si2400 microcontroller via S-registers SE5, SE6, SE7
and SE8. SE5 and SE6 are used as conduits to write
data to specific DSP registers and read status. SE8
defines the function of SE5 and SE6 depending on
whether they are being written to or read from. Care
must be exercised when writing to DSP registers. DSP
registers can only be written while the Si2400 is on-
hook and in the Command mode. Writing to any register
range values is likely to cause the DSP to exhibit
unpredictable behavior.
The DSP register address is 16-bits wide and the DSP
data field is 14-bits wide. DSP register addresses and
data are written in hexadecimal. To write a value to a
DSP register, the register address is written then the
data is written. When SE8 = 0x00, SE5(DADL) is written
with the low bits [7:0] of the DSP register address and
SE6 (DADH) is written with the high bits [15:8] of the
DSP address. When SE8 = 0x01, SE5 (DDL) is written
with the low bits [7:0] of the DSP data word
corresponding to the previously written address and
SE6 (DDH) is written with the high bits [15:8] of the data
word corresponding to the previously written address.
Example 1 below illustrates the proper procedure for
writing to DSP registers.
Example1:
The user would like to program call
progress filter coefficient A2_k0 (0x15) to be 309
(0x135).
Host
Command:
ATSE8=00SE6=00SE5=15SE8=01SE6=01SE5=35SE8=00
In the command above, ATSE8=00 sets up registers
SE5 and SE6 as DSP address registers. SE6=00 sets
the high bits of the address, and SE5=15 sets the low
bits. SE8=01 sets up registers SE5 and SE6 as DSP
data registers for the previously written DSP address
(0x15). SE6=01 sets the high 6 bits of the 14-bit data
word, and SE5=35 sets the low 8 bits of the 14-bit data
word.
Table 24. Low-Level DSP Parameters
DSP Reg. Addr.
Name
Description
Function
Default
(dec)
0x0002
XMTL
DAA modem full scale transmit level,
default = –10 dBm
Level = 20log10 (XTML/4096)
–10 dBm
4096
0x0003
DTML
DTMF high tone transmit level,
default = –5.5 dBm
Level = 20log10 (DTML/4868)
–5.5 dBm
4868
0x0004
DTMT
DTMF twist ratio (low/high), default = –2 dBm Level = 20log
10 (DTMT/3277) –
2dB
3277
0x0005
UFRQ User-defined transmit tone frequency. See
register SE5 (SE8=0x02 (Write Only))
f = (9600/512) UFRQ (Hz)
91
0x0006
CPDL
Call progress detect level (see Figure 13),
default = –43 dBm
Level = 20log10 (4096/CPDL)
–43 dBm
4096
0x0007
UDFD1 User-defined frequency detector 1. Center
frequency for detector 1.
UDFD1 = 8192 cos (2
π f/9600)
4987
0x0008
UDFD2 User-defined frequency detector 2. Center
frequency for detector 2.
UDFD2 = 8192 cos (2
π f/9600)
536
0x0009
UDFD3 User-defined frequency detector 3. Center
frequency for detector 3.
UDFD3 = 8192 cos (2
π f/9600)
4987
0x000A
UDFD4 User-defined frequency detector 4. Center
frequency for detector 4.
UDFD4 = 8192 cos (2
π f/9600)
536
0x000B
TGNL
Tone generation level associated with TONC
(SE5 (SE8 = 0x02) Write Only Definition),
default = –10 dBm
Level = 20log10 (TGNL/2896)
– 10 dBm
2896
相关PDF资料 |
PDF描述 |
|---|---|
| SI3050-E1-FM | IC VOICE DAA SYSTEM SIDE 24QFN |
| JBXEA2G07FSSDS | CONN RCPT 7POS DOUBLE NUT SOLDER |
| VE-J6V-IY-B1 | CONVERTER MOD DC/DC 5.8V 50W |
| VE-J6T-IY-B1 | CONVERTER MOD DC/DC 6.5V 50W |
| VE-2NX-IX-F1 | CONVERTER MOD DC/DC 5.2V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI3015-F-FSR | 制造商:Silicon Laboratories Inc 功能描述:Modem Chip Chipset 2.4Kbps 16-Pin SOIC T/R 制造商:Silicon Laboratories Inc 功能描述:MODEM CHIP CHIPSET ISOMODEM 2.4KBPS 16SOIC - Tape and Reel 制造商:Silicon Laboratories 功能描述:Modem Chip Chipset 2.4Kbps 16-Pin SOIC T/R |
| SI3015-FS | 功能描述:IC ISOMODEM LINE-SIDE DAA 16SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 调制解调器 - IC 和模块 系列:ISOmodem® 标准包装:25 系列:- 数据格式:V.21，V.22，V.23，V.29，V.32，V.34，V.90，V.92，Bell 103，Bell 212A 波特率:33.6k 电源电压:3.3V 安装类型:- 封装/外壳:- 供应商设备封装:- 包装:托盘 配用:591-1013-ND - KIT DEV SOCKETMODEM PARALLEL591-1009-ND - KIT DEV SRL SOCKETMODEM UNIVERSL 其它名称:MT5656SMI-P-V-34.R2-SPMT5656SMI-P-V-34.R2-SP-NDQ4711574 |
| SI3015-FSR | 制造商:Silicon Laboratories Inc 功能描述:SI2403 ISOMODEM LINE-SIDE LEAD-FREE SOIC 0 TO 70 DEG. C - Tape and Reel |
| SI3015-KS | 功能描述:电信线路管理 IC SI2400 Line Side RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI3015-KSR | 功能描述:电信线路管理 IC SI2400 Line Side RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。