- 您现在的位置：买卖IC网 > PDF目录10908 > SI3015-F-FS (Silicon Laboratories Inc)IC ISOMODEM LINE-SIDE DAA 16SOIC PDF资料下载
参数资料
| 型号： | SI3015-F-FS |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 7/94页 |
| 文件大小： | 0K |
| 描述： | IC ISOMODEM LINE-SIDE DAA 16SOIC |
| 标准包装： | 48 |
| 系列： | ISOmodem® |
| 数据格式： | V.90 |
| 波特率： | 2.4k |
| 电源电压： | 3.3V，5V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SOIC N |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页
Si2400
Rev. 1.3
15
5.1. Digital Interface
The Si2400 has a universal asynchronous serial
interface
(UART)
compatible
with
standard
microcontroller serial interfaces. After power-up or
reset,
the
speed
of
the
serial
(Data
Terminal
Equipment—DTE)
interface
is
set
by
default
to
2400 bps with the 8-bit, no parity, and one stop bit (8N1)
format described below. The PCM codec serial interface
is
disabled
by
default
and
CLKOUT
is
set
to
9.8304 MHz after power-up or reset.
The serial interface DTE rate can be modified by writing
SE0[2:0] (SD) with the value corresponding to the
desired DTE rate. (See Table 11.) This is accomplished
with
the
command
ATSE0=xx
where
xx
is
the
hexadecimal value of the SE0 register.
Immediately after the ATSE0=xx string is sent, the host
UART must be reprogrammed to the new DTE rate in
order to communicate with the Si2400.
The three highest DTE rates (228613, 245760, 307200)
are required for transferring PCM data from the host to
the Si2400 PCM interface for the transmission of voice
over the phone line or through the voice codec.
5.2. Configurations and Data Rates
The Si2400 can be configured to any of the Bell and
CCITT operation modes in Table 12. The modem, when
configured for V.22bis, will connect at 1200 bps if the far
end modem is configured for V.22. This device also
supports SIA and other protocols for the security
industry. Table 10 provides the modulation method,
carrier frequencies, data rate, baud rate and notes on
standard compliance for each modem configuration of
the Si2400. Table 12 shows example register settings
(S07) for some of the modem configurations.
As shown in Figure 6, 8-bit and 9-bit data modes refer to
the DTE format over the UART. Line data formats are
configured through registers S07 (MF1) and S15 (MLC).
If the number of bits specified by the DTE format differs
from the number of bits specified by the DCE (Data
Communications Equipment or Line) format, the MSBs
will either be dropped or bit-stuffed, as appropriate. For
example, if the DTE format is 9 data bits (9N1), and the
line data format is 8 data bits (8N1), then the MSB from
the DTE will be dropped as the 9-bit word is passed
from the DTE side to the DCE (line) side. In this case,
the dropped ninth bit can then be used as an escape
mechanism. However, if the DTE format is 8N1and the
line data format is 9N1, an MSB equal to 0 will be added
to the 8-bit word as it is passed from the DTE side to the
DCE side.
The Si2400 UART does not continuously check for stop
bits on the incoming digital data. Therefore, if the TXD
pin is not high, the RXD pin may echo meaningless
characters to the host UART. This requires the host
UART to flush its receiver FIFO upon initialization.
Figure 6. Link and Line Data Formats
5.2.1. Command/Data Mode
Upon reset, the modem will be in command mode and
will accept AT-style commands. An outgoing modem
call can be made using the “ATDT#” (tone dial) or
“ATDP#” (pulse dial) command after the device is
configured. If the handshake is successful, the modem
will respond with the “c”, “d”, or “v” string and enter data
mode. (The byte following the “c”, “d”, or “v” will be the
first data byte.) At this point, AT-style commands are not
accepted. There are three methods which may be used
to return the Si2400 to command mode:
Table 11. DTE Rates
DTE Rate (bps)
SE0[2:0] (SD)
300
000
1200
001
2400
010
9600
011
19200
100
228613
101
245760
110
307200
111
Table 12. Modem Configuration Examples
(S07[7] (HDEN) = 0, S07[6] (BD) = 0)
Modem Protocol
Register S07 Values
V.22bis
0x06
V.22
0x02
V.21
0x03
Bell 212A
0x00
Bell 103
0x01
V.23 (1200 tx, 75 rx)
0x16
V.23 (75 tx, 1200 rx)
0x24
V.23 (600 tx, 75 rx)
0x12
V.23 (75 tx, 600 rx)
0x20
DTE Interface
Data Rate: SE0[2:0] (SD)
Data Form at: SE0[3] (ND)
DCE (Line) Interface
Data Rate: S07 (MF1)
Data Form at: S15 (MLC)
Si3015
Si2400
RJ11
TXD
RXD
相关PDF资料 |
PDF描述 |
|---|---|
| SI3050-E1-FM | IC VOICE DAA SYSTEM SIDE 24QFN |
| JBXEA2G07FSSDS | CONN RCPT 7POS DOUBLE NUT SOLDER |
| VE-J6V-IY-B1 | CONVERTER MOD DC/DC 5.8V 50W |
| VE-J6T-IY-B1 | CONVERTER MOD DC/DC 6.5V 50W |
| VE-2NX-IX-F1 | CONVERTER MOD DC/DC 5.2V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI3015-F-FSR | 制造商:Silicon Laboratories Inc 功能描述:Modem Chip Chipset 2.4Kbps 16-Pin SOIC T/R 制造商:Silicon Laboratories Inc 功能描述:MODEM CHIP CHIPSET ISOMODEM 2.4KBPS 16SOIC - Tape and Reel 制造商:Silicon Laboratories 功能描述:Modem Chip Chipset 2.4Kbps 16-Pin SOIC T/R |
| SI3015-FS | 功能描述:IC ISOMODEM LINE-SIDE DAA 16SOIC RoHS:是 类别:集成电路 (IC) >> 接口 - 调制解调器 - IC 和模块 系列:ISOmodem® 标准包装:25 系列:- 数据格式:V.21，V.22，V.23，V.29，V.32，V.34，V.90，V.92，Bell 103，Bell 212A 波特率:33.6k 电源电压:3.3V 安装类型:- 封装/外壳:- 供应商设备封装:- 包装:托盘 配用:591-1013-ND - KIT DEV SOCKETMODEM PARALLEL591-1009-ND - KIT DEV SRL SOCKETMODEM UNIVERSL 其它名称:MT5656SMI-P-V-34.R2-SPMT5656SMI-P-V-34.R2-SP-NDQ4711574 |
| SI3015-FSR | 制造商:Silicon Laboratories Inc 功能描述:SI2403 ISOMODEM LINE-SIDE LEAD-FREE SOIC 0 TO 70 DEG. C - Tape and Reel |
| SI3015-KS | 功能描述:电信线路管理 IC SI2400 Line Side RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
| SI3015-KSR | 功能描述:电信线路管理 IC SI2400 Line Side RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。