- 您现在的位置：买卖IC网 > PDF目录16791 > SI5338-EVB (Silicon Laboratories Inc)BOARD EVALUATION SI5338 PDF资料下载
参数资料
| 型号： | SI5338-EVB |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 14/44页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION SI5338 |
| 标准包装： | 1 |
| 主要目的： | 计时，时钟发生器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | Si5338 |
| 主要属性： | LVPECL/LVDS：160 kHz 至 700 MHz，<1 ps RMS 标准抖动，零 ppm 频率错误 |
| 次要属性： | 基于 USB 的 GUI，用于编程，I2C/SMBus 兼容接口，1.8、2.5 或 3.3 V |
| 已供物品： | 板，线缆，CD，样品 |
| 产品目录页面： | 628 (CN2011-ZH PDF) |
| 相关产品： | 336-1555-5-ND - IC CLK GEN QUAD 200MHZ 24-QFN 336-1554-5-ND - IC CLK GEN QUAD 350MHZ 24-QFN 336-1553-5-ND - IC CLK GEN QUAD 700MHZ 24-QFN |
| 其它名称： | 336-1556 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
Si5338
Rev. 1.3
21
3.5.1. Ordering a Custom NVM Configuration
The Si5338 is orderable with a factory-programmed
custom NVM configuration. This is the simplest way of
using the Si5338 since it generates the desired output
frequencies at power-up or after a power-on reset
(POR). This default configuration can be reconfigured in
RAM through the I2C interface after power-up (see
Custom 7-bit I2C addresses may also be requested.
Note that for the A/B/C devices, the I2C LS bit address
is the logical “or” of the I2C address LS bit in Register 27
and the state of the I2C_LSB pin. If I2C_LSB pin
functionality is required, custom I2C addresses may
only be even numbers. For all other variants of the
device, custom I2C addresses may be even or odd
numbers.
See
the
Si5338
Reference
Manual:
Configuring the Si5338 without ClockBuilder Desktop
for more details.
The first step in ordering a custom device is generating
an NVM file which defines the input and output clock
frequencies and signal formats. This is easily done
using the ClockBuilder Desktop software (see "3.1.1.
GUI based software generates an NVM file, which is
used by the factory to manufacture custom parts. Each
custom part is marked with a unique part number
identifying the specific configuration (e.g., Si5338C-
A00100-GM). Consult your local sales representative
for more details on ordering a custom Si5338.
3.5.2. Creating a New Configuration for RAM
Any Si5338 device can be configured by writing to
registers in RAM through the I2C interface. A non-
factory programmed device must be configured in this
manner.
The first step is to determine all the register values for
the required configuration. This can be accomplished by
one of two methods.
1. Create a device configuration (register map) using
ClockBuilder Desktop (v3.0 or later; see "3.1.1.
a. Configure the frequency plan.
b. Configure the output driver format and supply
voltage.
c. Configure frequency and/or phase inc/dec (if
desired).
d. Configure spread spectrum (if desired).
e. Configure for zero-delay mode (if desired,
f.
If needed go to the Advanced tab and make
additional configurations.
g. Save the configuration using the Options >
Save Register Map File or Options > Save C
code Header.
2. Create a device configuration, register by register,
using the Si5338 Reference Manual.
3.5.3. Writing a Custom Configuration to RAM
Writing a new configuration (register map) to the RAM
consists of pausing the LOL state-machine, writing new
values to the IC accounting for the write-allowed mask
(see the Si5338 Reference Manual, “10. Si5338
Registers”), validating the input clock or crystal, locking
the PLL to the input with the new configuration,
restarting the LOL state-machine, and calibrating the
VCO for robust operation across temperature. The flow
chart in Figure 9 enumerates the details:
Note: The write-allowed mask specifies which bits must be
read and modified before writing the entire register
byte (a.k.a. read-modify-write). “AN428: Jump Start: In-
System, Flash-Based Programming for Silicon Labs’
Timing Products” illustrates the procedure defined in
Section 3.5.2 with ANSI C code.
相关PDF资料 |
PDF描述 |
|---|---|
| H3AAH-2606G | IDC CABLE - HSC26H/AE26G/HSC26H |
| 0982660138 | CBL 12POS 0.5MM JMPR TYPE D 1' |
| 0982661084 | CBL 37POS 0.5MM JMPR TYPE D 6" |
| HMC08DRTH | CONN EDGECARD 16POS DIP .100 SLD |
| EBC43DCSD-S288 | CONN EDGECARD 86POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| SI5338F-A01839-GM | 制造商:Silicon Laboratories Inc 功能描述:CLOCK - Bulk |
| SI5338F-A01839-GMR | 制造商:Silicon Laboratories Inc 功能描述:CLOCK - Tape and Reel |
| Si5338F-A-GM | 功能描述:时钟发生器及支持产品 I2C-PRGRMBL clock generatr 0.16-200MHz RoHS:否 制造商:Silicon Labs 类型:Clock Generators 最大输入频率:14.318 MHz 最大输出频率:166 MHz 输出端数量:16 占空比 - 最大:55 % 工作电源电压:3.3 V 工作电源电流:1 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-56 |
| SI5338F-A-GMR | 功能描述:时钟发生器及支持产品 I2C-Program Clk Gen 0.16-200MHz Pin-Ctrl RoHS:否 制造商:Silicon Labs 类型:Clock Generators 最大输入频率:14.318 MHz 最大输出频率:166 MHz 输出端数量:16 占空比 - 最大:55 % 工作电源电压:3.3 V 工作电源电流:1 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-56 |
| Si5338F-B-GM | 功能描述:时钟发生器及支持产品 I2C-PRGRMBL clock generatr 0.16-200MHz RoHS:否 制造商:Silicon Labs 类型:Clock Generators 最大输入频率:14.318 MHz 最大输出频率:166 MHz 输出端数量:16 占空比 - 最大:55 % 工作电源电压:3.3 V 工作电源电流:1 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-56 |
发布紧急采购，3分钟左右您将得到回复。