参数资料
型号: ST7PLU05MAE
厂商: STMICROELECTRONICS
元件分类: 微控制器/微处理器
英文描述: 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO8
封装: 0.150 INCH, ROHS COMPLIANT, PLASTIC, SOP-8
文件页数: 77/124页
文件大小: 1995K
代理商: ST7PLU05MAE
I/O ports
ST7LUS5, ST7LU05, ST7LU09
9
I/O ports
9.1
Introduction
The I/O port offers different functional modes:
transfer of data through digital inputs and outputs
and for specific pins:
external interrupt generation
alternate signal input/output for the on-chip peripherals.
An I/O port contains up to six pins. Each pin (except PA3/RESET) can be programmed
independently as digital input (with or without interrupt generation) or digital output.
9.2
Functional description
Each port has two main registers:
Data Register (DR)
Data Direction Register (DDR)
and one optional register:
Option Register (OR)
Each I/O pin may be programmed using the corresponding register bits in the DDR and OR
registers, with bit X corresponding to pin X of the port. The same correspondence is used for
the DR register.
The following description takes into account the OR register (for specific ports which do not
provide this register refer to Section 9.6: I/O port implementation). The generic I/O block
diagram is shown in Figure 26.
9.2.1
Input modes
The input configuration is selected by clearing the corresponding DDR register bit.
In this case, reading the DR register returns the digital value applied to the external I/O pin.
Different input modes can be selected by software through the OR register.
Note:
1
Writing the DR register modifies the latch value but does not affect the pin status.
2
PA3 cannot be configured as input.
External interrupt function
When an I/O is configured as Input with Interrupt, an event on this I/O can generate an
external interrupt request to the CPU.
Each pin can independently generate an interrupt request. The interrupt sensitivity is
independently programmable using the sensitivity bits in the EICR register.
External interrupts are hardware interrupts. Fetching the corresponding interrupt vector
automatically clears the request latch. Changing the sensitivity of a particular external
interrupt clears this pending interrupt. This can be used to clear unwanted pending
interrupts.
相关PDF资料
PDF描述
ST7PLU09MAE 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO8
ST90135M5T6 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP80
ST90T158M9Q6 16-BIT, OTPROM, 24 MHz, MICROCONTROLLER, PQFP80
ST90158M9Q6 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP80
ST9020B6/XX 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PDIP40
相关代理商/技术参数
参数描述
ST7PMC1K2B3 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-bit MCU with nested interrupts, Flash, 10-bit ADC, brushless motor control, five timers, SPI, LINSCI?
ST7PMC1K2B6 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT MCU WITH NESTED INTERRUPTS, FLASH, 10-BIT ADC, BRUSHLESS MOTOR CONTROL, FIVE TIMERS, SPI, LINSCI
ST7PMC1K2T3 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-bit MCU with nested interrupts, Flash, 10-bit ADC, brushless motor control, five timers, SPI, LINSCI?
ST7PMC1K2T6 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT MCU WITH NESTED INTERRUPTS, FLASH, 10-BIT ADC, BRUSHLESS MOTOR CONTROL, FIVE TIMERS, SPI, LINSCI
ST7PMC1K2T6/ST7PMC1K2 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:8-BIT MCU WITH NESTED INTERRUPTS, FLASH, 10-BIT ADC, BRUSHLESS MOTOR CONTROL, FIVE TIMERS, SPI, LINSCI