参数资料
型号: TMP86CH47IUG
厂商: Toshiba Corporation
英文描述: Zener Diode; Application: General; Pd (mW): 500; Vz (V): 17.5 to 18.3; Condition Iz at Vz (mA): 5; C (pF) max: -; Condition VR at C (V):   ESD (kV) min: -; Package: DO-35
中文描述: 8位微控制器
文件页数: 19/160页
文件大小: 1627K
代理商: TMP86CH47IUG
Page 11
TMP86CH47IUG
Note 1: In single clock mode, do not set DV7CK to “1”.
Note 2: Do not set “1” on DV7CK while the low-frequency clock is not operated stably.
Note 3: fc: High-frequency clock [Hz], fs: Low-frequency clock [Hz], *: Don’t care
Note 4: In SLOW1/2 and SLEEP1/2 modes, the DV7CK setting is ineffective, and fs is input to the 7th stage of the divider.
Note 5: When STOP mode is entered from NORMAL1/2 mode, the DV7CK setting is ineffective during the warm-up period after
release of STOP mode, and the 6th stage of the divider is input to the 7th stage during this period.
2.2.2.2
Machine cycle
Instruction execution and peripheral hardware operation are synchronized with the main system clock.
The minimum instruction execution unit is called an “machine cycle”. There are a total of 10 different
types of instructions for the TLCS-870/C Series: Ranging from 1-cycle instructions which require one
machine cycle for execution to 10-cycle instructions which require 10 machine cycles for execution. A
machine cycle consists of 4 states (S0 to S3), and each state consists of one main system clock.
Figure 2-5 Machine Cycle
2.2.3
Operation Mode Control Circuit
The operation mode control circuit starts and stops the oscillation circuits for the high-frequency and low-
frequency clocks, and switches the main system clock. There are three operating modes: Single clock mode,
dual clock mode and STOP mode. These modes are controlled by the system control registers (SYSCR1 and
SYSCR2). Figure 2-6 shows the operating mode transition diagram.
2.2.3.1
Single-clock mode
Only the oscillation circuit for the high-frequency clock is used, and P21 (XTIN) and P22 (XTOUT)
pins are used as input/output ports. The main-system clock is obtained from the high-frequency clock. In
the single-clock mode, the machine cycle time is 4/fc [s].
(1)
NORMAL1 mode
In this mode, both the CPU core and on-chip peripherals operate using the high-frequency clock.
The TMP86CH47IUG is placed in this mode after reset.
Timing Generator Control Register
TBTCR
(0036H)
7
6
5
4
3
2
1
0
(DVOEN)
(DVOCK)
DV7CK
(TBTEN)
(TBTCK)
(Initial value: 0000 0000)
DV7CK
Selection of input to the 7th stage
of the divider
0: fc/2
8
[Hz]
1: fs
R/W
Main system clock
State
Machine cycle
S3
S2
S1
S0
S3
S2
S1
S0
1/fc or 1/fs [s]
相关PDF资料
PDF描述
TMP86CH47SUG Zener Diode; Application: General; Pd (mW): 500; Vz (V): 18.1 to 19.0; Condition Iz at Vz (mA): 5; C (pF) max: -; Condition VR at C (V):   ESD (kV) min: -; Package: DO-35
TMP86CH49FG Zener Diode; Application: General; Pd (mW): 500; Vz (V): 18.8 to 19.7; Condition Iz at Vz (mA): 2; C (pF) max: -; Condition VR at C (V):   ESD (kV) min: -; Package: DO-35
TMP86CH72FG Zener Diode; Application: General; Pd (mW): 500; Vz (V): 19.5 to 20.4; Condition Iz at Vz (mA): 2; C (pF) max: -; Condition VR at C (V):   ESD (kV) min: -; Package: DO-35
TMP86CK74AFG Zener Diode; Application: General; Pd (mW): 500; Vz (V): 20.2 to 21.1; Condition Iz at Vz (mA): 2; C (pF) max: -; Condition VR at C (V):   ESD (kV) min: -; Package: DO-35
TMP86CM23AUG Zener Diode; Application: General; Pd (mW): 500; Vz (V): 20.9 to 21.9; Condition Iz at Vz (mA): 2; C (pF) max: -; Condition VR at C (V):   ESD (kV) min: -; Package: DO-35
相关代理商/技术参数
参数描述
TMP86CH47SUG 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:8 Bit Microcontroller
TMP86CH47U 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:CMOS 8 BIT MICROCONTROLLER
TMP86CH47UG 制造商:Toshiba America Electronic Components 功能描述:MCU 8BIT TLCS-870 CISC 16KB ROM 5V 44PQFP - Rail/Tube
TMP86CH49FG 制造商:TOSHIBA 制造商全称:Toshiba Semiconductor 功能描述:8 Bit Microcontroller
TMP86CH72FG 制造商:Toshiba America Electronic Components 功能描述:TLCS870/C 16K ROM , VFT - Rail/Tube