参数资料
型号: TPS65073TRSLRQ1
厂商: TEXAS INSTRUMENTS INC
元件分类: 电源管理
英文描述: POWER SUPPLY SUPPORT CKT, PQCC48
封装: 6 X 6 MM, 0.4 MM PITCH, PLASTIC, QFN-48
文件页数: 60/90页
文件大小: 1375K
代理商: TPS65073TRSLRQ1
L
Vout
1
Vin
I
= Vout
L
-
D
L
Lmax
outmax
I
= I
+
2
D
www.ti.com
SLVSAP7 – JANUARY 2011
APPLICATION INFORMATION
STEP-DOWN CONVERTERS
OUTPUT FILTER DESIGN (INDUCTOR AND OUTPUT CAPACITOR)
Inductor Selection
The step-down converters operate typically with 2.2mH output inductor. Larger or smaller inductor values can be
used to optimize the performance of the device for specific operation conditions. The selected inductor has to be
rated for its DC resistance and saturation current. The DC resistance of the inductance will influence directly the
efficiency of the converter. Therefore an inductor with lowest DC resistance should be selected for highest
efficiency.
Equation 4 can be used to calculate the maximum inductor current under static load conditions. The saturation
current of the inductor should be rated higher than the maximum inductor current as calculated with Equation 4.
This is recommended because during heavy load transient the inductor current will rise above the calculated
value.
(4)
(5)
With
f = Switching Frequency (2.25MHz typical)
L = Inductor Value
ΔIL= Peak to Peak inductor ripple current
ILmax = Maximum Inductor current
The highest inductor current will occur at maximum Vin.
Open core inductors have a soft saturation characteristic and they can usually handle higher inductor currents
versus a comparable shielded inductor.
A more conservative approach is to select the inductor current rating just for the maximum switch current of the
corresponding converter. It must be considered, that the core material from inductor to inductor differs and will
have an impact on the efficiency especially at high switching frequencies.
Refer to Table 4 and the typical applications for possible inductors.
Table 4. Tested Inductors
INDUCTOR TYPE
RECOMMENDED
INDUCTOR VALUE
SUPPLIER
MAXIMUM DC
CURRENT
LPS3010
0.6 A
2.2 mH
Coilcraft
LPS3015
1.2 A
2.2 mH
Coilcraft
LPS4018
1.5 A
2.2 mH
Coilcraft
VLCF4020
1.5 A
2.2 mH
TDK
Output Capacitor Selection
The advanced Fast Response voltage mode control scheme of the two converters allow the use of small ceramic
capacitors with a typical value of 10mF, without having large output voltage under and overshoots during heavy
load transients. Ceramic capacitors having low ESR values result in lowest output voltage ripple and are
therefore recommended. Please refer to for recommended components.
If ceramic output capacitors are used, the capacitor RMS ripple current rating will always meet the application
requirements. Just for completeness the RMS ripple current is calculated as:
Copyright 2011, Texas Instruments Incorporated
63
相关PDF资料
PDF描述
TC151A4924EOA713 0.25 A SWITCHING REGULATOR, 50 kHz SWITCHING FREQ-MAX, PDSO8
TC161B3514EOA723 0.25 A SWITCHING REGULATOR, 100 kHz SWITCHING FREQ-MAX, PDSO8
TC161B1717EOA713 0.25 A SWITCHING REGULATOR, 100 kHz SWITCHING FREQ-MAX, PDSO8
TC161A5520EOA713 0.25 A SWITCHING REGULATOR, 100 kHz SWITCHING FREQ-MAX, PDSO8
TC161A5825EOA713 0.25 A SWITCHING REGULATOR, 100 kHz SWITCHING FREQ-MAX, PDSO8
相关代理商/技术参数
参数描述
TPS650830EVM-095 功能描述:TPS650830 - Power Management, Special Purpose: Mobiles Evaluation Board 制造商:texas instruments 系列:- 零件状态:有效 主要用途:电源管理,专用型: 手机 嵌入式:- 使用的 IC/零件:TPS650830 主要属性:- 辅助属性:图形用户接口,I2C 接口 所含物品:板 标准包装:1
TPS650830ZAJT 功能描述:- Converter, Mobile PCs Voltage Regulator IC 8 Output 168-NFBGA (7x7) 制造商:texas instruments 系列:- 包装:剪切带(CT) 零件状态:有效 应用:转换器,移动式个人电脑 电压 - 输入:5.4 V ~ 24 V 输出数:8 电压 - 输出:多重 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:168-TFBGA 供应商器件封装:168-NFBGA(7x7) 标准包装:1
TPS650830ZCGT 功能描述:- Converter, Mobile PCs Voltage Regulator IC 8 Output 159-NFBGA (9x9) 制造商:texas instruments 系列:- 包装:剪切带(CT) 零件状态:有效 应用:转换器,移动式个人电脑 电压 - 输入:5.4 V ~ 24 V 输出数:8 电压 - 输出:多重 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:159-TFBGA 供应商器件封装:159-NFBGA(9x9) 标准包装:1
TPS650860A0RSKT 功能描述:D-CAP2? Controller, Multicore, CPU, FPGA, SOC’s Voltage Regulator IC 8 Output 64-QFN (8x8) 制造商:texas instruments 系列:D-CAP2?? 包装:剪切带(CT) 零件状态:有效 应用:控制器,多核,CPU,FPGA,SOC 应用 电压 - 输入:4.5 V ~ 21 V 输出数:8 电压 - 输出:多重 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:64-VFQFN 裸露焊盘 供应商器件封装:64-QFN(8x8) 标准包装:1
TPS650860EVM-116 功能描述:EVALUATION MODULE 制造商:texas instruments 系列:* 零件状态:在售 标准包装:1