参数资料
型号: TSC87C51-L16IEB
厂商: ATMEL CORP
元件分类: 微控制器/微处理器
英文描述: 8-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PQFP44
封装: 1.40 MM HEIGHT, VQFP-44
文件页数: 13/176页
文件大小: 2962K
代理商: TSC87C51-L16IEB
11
2535J–AVR–08/10
ATtiny13
Figure 4-3.
The X-, Y-, and Z-registers
In the different addressing modes these address registers have functions as fixed displacement,
automatic increment, and automatic decrement (see the instruction set reference for details).
4.5
Stack Pointer
The Stack is mainly used for storing temporary data, for storing local variables and for storing
return addresses after interrupts and subroutine calls. The Stack Pointer Register always points
to the top of the Stack. Note that the Stack is implemented as growing from higher memory loca-
tions to lower memory locations. This implies that a Stack PUSH command decreases the Stack
Pointer.
The Stack Pointer points to the data SRAM Stack area where the Subroutine and Interrupt
Stacks are located. This Stack space in the data SRAM is automaticall defined to the last
address in SRAM during power on reset. The Stack Pointer must be set to point above 0x60.
The Stack Pointer is decremented by one when data is pushed onto the Stack with the PUSH
instruction, and it is decremented by two when the return address is pushed onto the Stack with
subroutine call or interrupt. The Stack Pointer is incremented by one when data is popped from
the Stack with the POP instruction, and it is incremented by two when data is popped from the
Stack with return from subroutine RET or return from interrupt RETI.
The AVR Stack Pointer is implemented as two 8-bit registers in the I/O space. The number of
bits actually used is implementation dependent. Note that the data space in some implementa-
tions of the AVR architecture is so small that only SPL is needed. In this case, the SPH Register
will not be present.
4.5.1
SPL - Stack Pointer Low.
15
XH
XL
0
X-register
70
7
0
R27 (0x1B)
R26 (0x1A)
15
YH
YL
0
Y-register
70
7
0
R29 (0x1D)
R28 (0x1C)
15
ZH
ZL
0
Z-register
7
070
R31 (0x1F)
R30 (0x1E)
Bit
151413121110
9
8
SP7
SP6
SP5
SP4
SP3
SP2
SP1
SP0
SPL
76543210
Read/Write
R/W
Initial Value
10011111
相关PDF资料
PDF描述
TSC87C51-20CBR 8-BIT, OTPROM, 20 MHz, MICROCONTROLLER, PQCC44
TSC87C51-25CIB 8-BIT, OTPROM, 25 MHz, MICROCONTROLLER, CQCC44
TSC87C51-33CBB 8-BIT, OTPROM, 33 MHz, MICROCONTROLLER, PQCC44
TSC87C52-33CDB 8-BIT, OTPROM, 33 MHz, MICROCONTROLLER, PQFP44
T89C51RD2-3CVCM 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PDIP40
相关代理商/技术参数
参数描述
TSC888AILT 功能描述:电流灵敏放大器 Sense Amplifier 20 Gain RoHS:否 制造商:Texas Instruments 通道数量: 共模抑制比(最小值):110 dB 输入补偿电压:80 uV 电源电压-最大:5.5 V 电源电压-最小:2.7 V 电源电流:350 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-16 封装:Reel
TSC888BILT 功能描述:电流灵敏放大器 Sense Amplifier 50 Gain RoHS:否 制造商:Texas Instruments 通道数量: 共模抑制比(最小值):110 dB 输入补偿电压:80 uV 电源电压-最大:5.5 V 电源电压-最小:2.7 V 电源电流:350 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-16 封装:Reel
TSC888CILT 功能描述:电流灵敏放大器 Sense Amplifier 100 Gain RoHS:否 制造商:Texas Instruments 通道数量: 共模抑制比(最小值):110 dB 输入补偿电压:80 uV 电源电压-最大:5.5 V 电源电压-最小:2.7 V 电源电流:350 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-16 封装:Reel
TSC9 制造商:未知厂家 制造商全称:未知厂家 功能描述:EURO TERMINAL BLOCKS
TSC903 制造商:Laird Technologies Inc 功能描述:CLIP TO-3P 制造商:Laird Technologies Inc 功能描述:CLIP, TO-3P 制造商:Laird Technologies Inc 功能描述:CLIP, TO-3P; External Width:6.5mm; SVHC:No SVHC (18-Jun-2012); Isolation Voltage:1kV; Length:30mm; Material:Steel; Package / Case:TO-3P, TO-218, TO-247; Packages Cooled:TO-3P, TO-218, TO-247; Pad Thickness Max:0.5mm; Panel Thickness ;RoHS Compliant: Yes 制造商:Laird Technologies Inc 功能描述:CLIP, TO-3P; External Width:6.5mm; SVHC:No SVHC (18-Jun-2012); Isolation Voltage:1kV; Length:30mm; Material:Steel; Package / Case:TO-3P, TO-218, TO-247; Packages Cooled:TO-218, TO-247, TO-3P; Pad Thickness Max:0.5mm; Panel Thickness ;RoHS Compliant: Yes