收藏本站
参数资料
型号： TSC87C51-L16IEB
厂商： ATMEL CORP
元件分类： 微控制器/微处理器
英文描述： 8-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PQFP44
封装： 1.40 MM HEIGHT, VQFP-44
文件页数： 9/176页
文件大小： 2962K
代理商： TSC87C51-L16IEB
106
2535J–AVR–08/10
ATtiny13
17.6.1
Serial Programming Algorithm
When writing serial data to the ATtiny13, data is clocked on the rising edge of SCK.
When reading data from the ATtiny13, data is clocked on the falling edge of SCK. See Figure
18-5 on page 121 and Figure 18-4 on page 121 for timing details.
To program and verify the ATtiny13 in the Serial Programming mode, the following sequence is
recommended (see four byte instruction formats in Table 17-9 on page 107):
1. Power-up sequence:
Apply power between VCC and GND while RESET and SCK are set to “0”. In some sys-
tems, the programmer can not guarantee that SCK is held low during power-up. In this
case, RESET must be given a positive pulse after SCK has been set to “0”. The pulse
duration must be at least tRST (miniumum pulse widht of RESET pin, see Table 18-4 on
page 119) plus two CPU clock cycles.
2. Wait for at least 20 ms and enable serial programming by sending the Programming
Enable serial instruction to pin MOSI.
3. The serial programming instructions will not work if the communication is out of syn-
chronization. When in sync. the second byte (0x53), will echo back when issuing the
third byte of the Programming Enable instruction. Whether the echo is correct or not, all
four bytes of the instruction must be transmitted. If the 0x53 did not echo back, give
RESET a positive pulse and issue a new Programming Enable command.
4. The Flash is programmed one page at a time. The memory page is loaded one byte at
a time by supplying the 4 LSB of the address and data together with the Load Program
memory Page instruction. To ensure correct loading of the page, the data low byte must
be loaded before data high byte is applied for a given address. The Program memory
Page is stored by loading the Write Program memory Page instruction with the 5 MSB
of the address. If polling (RDY/BSY) is not used, the user must wait at least tWD_FLASH
before issuing the next page. (See Table 17-8 on page 107.) Accessing the serial pro-
gramming interface before the Flash write operation completes can result in incorrect
programming.
5. A: The EEPROM array is programmed one byte at a time by supplying the address and
data together with the appropriate Write instruction. An EEPROM memory location is
first automatically erased before new data is written. If polling (RDY/BSY) is not used,
the user must wait at least tWD_EEPROM before issuing the next byte. (See Table 17-8 on
page 107.) In a chip erased device, no 0xFFs in the data file(s) need to be pro-
grammed.
B: The EEPROM array is programmed one page at a time. The Memory page is loaded
one byte at a time by supplying the 2 LSB of the address and data together with the
Load EEPROM Memory Page instruction. The EEPROM Memory Page is stored by
loading the Write EEPROM Memory Page Instruction with the 4 MSB of the address.
When using EEPROM page access only byte locations loaded with the Load EEPROM
Memory Page instruction is altered. The remaining locations remain unchanged. If poll-
ing (RDY/BSY) is not used, the used must wait at least tWD_EEPROM before issuing the
next page (See Table 17-6 on page 104). In a chip erased device, no 0xFF in the data
file(s) need to be programmed.
6. Any memory location can be verified by using the Read instruction which returns the
content at the selected address at serial output MISO.
7. At the end of the programming session, RESET can be set high to commence normal
operation.
8. Power-off sequence (if needed):
Set RESET to “1”.
Turn VCC power off.
相关PDF资料
PDF描述
TSC87C51-20CBR 8-BIT, OTPROM, 20 MHz, MICROCONTROLLER, PQCC44
TSC87C51-25CIB 8-BIT, OTPROM, 25 MHz, MICROCONTROLLER, CQCC44
TSC87C51-33CBB 8-BIT, OTPROM, 33 MHz, MICROCONTROLLER, PQCC44
TSC87C52-33CDB 8-BIT, OTPROM, 33 MHz, MICROCONTROLLER, PQFP44
T89C51RD2-3CVCM 8-BIT, FLASH, 40 MHz, MICROCONTROLLER, PDIP40
相关代理商/技术参数
参数描述
TSC888AILT 功能描述:电流灵敏放大器 Sense Amplifier 20 Gain RoHS:否 制造商:Texas Instruments 通道数量: 共模抑制比（最小值）:110 dB 输入补偿电压:80 uV 电源电压-最大:5.5 V 电源电压-最小:2.7 V 电源电流:350 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-16 封装:Reel
TSC888BILT 功能描述:电流灵敏放大器 Sense Amplifier 50 Gain RoHS:否 制造商:Texas Instruments 通道数量: 共模抑制比（最小值）:110 dB 输入补偿电压:80 uV 电源电压-最大:5.5 V 电源电压-最小:2.7 V 电源电流:350 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-16 封装:Reel
TSC888CILT 功能描述:电流灵敏放大器 Sense Amplifier 100 Gain RoHS:否 制造商:Texas Instruments 通道数量: 共模抑制比（最小值）:110 dB 输入补偿电压:80 uV 电源电压-最大:5.5 V 电源电压-最小:2.7 V 电源电流:350 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-16 封装:Reel
TSC9 制造商:未知厂家 制造商全称:未知厂家 功能描述:EURO TERMINAL BLOCKS
TSC903 制造商:Laird Technologies Inc 功能描述:CLIP TO-3P 制造商:Laird Technologies Inc 功能描述:CLIP, TO-3P 制造商:Laird Technologies Inc 功能描述:CLIP, TO-3P; External Width:6.5mm; SVHC:No SVHC (18-Jun-2012); Isolation Voltage:1kV; Length:30mm; Material:Steel; Package / Case:TO-3P, TO-218, TO-247; Packages Cooled:TO-3P, TO-218, TO-247; Pad Thickness Max:0.5mm; Panel Thickness ;RoHS Compliant: Yes 制造商:Laird Technologies Inc 功能描述:CLIP, TO-3P; External Width:6.5mm; SVHC:No SVHC (18-Jun-2012); Isolation Voltage:1kV; Length:30mm; Material:Steel; Package / Case:TO-3P, TO-218, TO-247; Packages Cooled:TO-218, TO-247, TO-3P; Pad Thickness Max:0.5mm; Panel Thickness ;RoHS Compliant: Yes
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*