- 您现在的位置：买卖IC网 > PDF目录20614 > USB-EA-CONVZ (Analog Devices Inc)SUPPORT BOARD ADUC8XX PDF资料下载
参数资料
| 型号： | USB-EA-CONVZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 55/68页 |
| 文件大小： | 0K |
| 描述： | SUPPORT BOARD ADUC8XX |
| 标准包装： | 1 |
| 类型： | 仿真器 |
| 适用于相关产品： | ADuC8xx |
| 所含物品： | 模块 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页当前第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页
REV. B
ADuC824
–59–
Timer 1 Generated Baud Rates
When Timer 1 is used as the baud rate generator, the baud rates
in Modes 1 and 3 are determined by the Timer 1 overflow rate and
the value of SMOD as follows:
Modes 1 and 3 Baud Rate = (2
SMOD/32)
× (Timer 1 Overflow Rate)
The Timer 1 interrupt should be disabled in this application. The
Timer itself can be configured for either timer or counter opera-
tion, and in any of its three running modes. In the most typical
application, it is configured for timer operation, in the autoreload
mode (high nibble of TMOD = 0100Binary). In that case, the baud
rate is given by the formula:
Modes 1 and 3 Baud Rate =
(2
SMOD/32)
× (Core Clock/(12 × [256-TH1]))
A very low baud rate can also be achieved with Timer 1 by leaving
the Timer 1 interrupt enabled, and configuring the timer to run
as a 16-bit timer (high nibble of TMOD = 0100Binary), and using
the Timer 1 interrupt to do a 16-bit software reload. Table XXVIII
below, shows some commonly-used baud rates and how they
might be calculated from a core clock frequency of 1.5728 MHz
and 12.58 MHz. Generally speaking, a 5% error is tolerable
using asynchronous (start/stop) communications.
Table XXVIII. Commonly Used Baud Rates, Timer 1
Ideal
Core
SMOD
TH1-Reload
Actual
%
Baud
CLK
Value
Baud
Error
9600
12.58
1
–7 (F9h)
9362
2.5
2400
12.58
1
–27 (E5h)
2427
1.1
1200
12.58
1
–55 (C9h)
1192
0.7
1200
1.57
1
–7 (F9h)
1170
2.5
Timer 2 Generated Baud Rates
Baud rates can also be generated using Timer 2. Using Timer 2 is
similar to using Timer 1 in that the timer must overflow 16 times
before a bit is transmitted/received. Because Timer 2 has a 16-bit
autoreload mode a wider range of baud rates is possible using
Timer 2.
Modes 1 and 3 Baud Rate = (1/16)
× (Timer 2 Overflow Rate)
Therefore, when Timer 2 is used to generate baud rates, the timer
increments every two clock cycles and not every core machine cycle
as before. Hence, it increments six times faster than Timer 1, and
therefore baud rates six times faster are possible. Because Timer 2
has 16-bit autoreload capability, very low baud rates are still possible.
Timer 2 is selected as the baud rate generator by setting the TCLK
and/or RCLK in T2CON. The baud rates for transmit and receive
can be simultaneously different. Setting RCLK and/or TCLK puts
Timer 2 into its baud rate generator mode as shown in Figure 42.
In this case, the baud rate is given by the formula:
Modes 1 and 3 Baud Rate
= (Core Clk)/(32
× [65536 – (RCAP2H, RCAP2L)])
Table XXIX shows some commonly used baud rates and how they
might be calculated from a core clock frequency of 1.5728 MHz
and 12.5829 MHz.
Table XXIX. Commonly Used Baud Rates, Timer 2
Ideal
Core
RCAP2H
RCAP2L
Actual
%
Baud
CLK
Value
Baud
Error
19200
12.58
–1 (FFh)
–20 (ECh)
19661
2.4
9600
12.58
–1 (FFh)
–41 (D7h)
9591
0.1
2400
12.58
–1 (FFh)
–164 (5Ch)
2398
0.1
1200
12.58
–2 (FEh)
–72 (B8h)
1199
0.1
9600
1.57
–1 (FFh)
–5 (FBh)
9830
2.4
2400
1.57
–1 (FFh)
–20 (ECh)
2458
2.4
1200
1.57
–1 (FFh)
–41 (D7h)
1199
0.1
CORE
CLK*
2
T2
PIN
TR2
CONTROL
TL2
(8-BITS)
TH2
(8-BITS)
RELOAD
EXEN2
CONTROL
T2EX
PIN
RCAP2L
RCAP2H
NOTE: OSC. FREQ. IS DIVIDED BY 2, NOT 12.
TIMER 2
OVERFLOW
2
16
RCLK
TCLK
RX
CLOCK
TX
CLOCK
0
1
0
SMOD
TIMER 1
OVERFLOW
TRANSITION
DETECTOR
EXF
2
TIMER 2
INTERRUPT
NOTE AVAILABILITY OF ADDITIONAL
EXTERNAL INTERRUPT
C/
T2 = 0
C/
T2 = 1
*THE CORE CLOCK IS THE OUTPUT OF THE PLL AS DESCRIBED ON PAGE 42.
Figure 42. Timer 2, UART Baud Rates
相关PDF资料 |
PDF描述 |
|---|---|
| RGP10KE-E3/54 | DIODE GPP 1A 800V 500NS DO-41 |
| A7NXB-1506G | CABLE D-SUB - AMN15B/AE15G/X |
| C1005C0G1H470J | CAP CER 47PF 50V 5% NP0 0402 |
| SLF6045T-220M1R1-3PF | INDUCTOR POWER 22UH 1.1A SMD |
| GBM12DRTI-S13 | CONN EDGECARD 24POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| USB-ETH ADAPTER | 制造商:DANAHER - FLUKE 功能描述:USB TO 10/100MBPS ETHERNET ADAPTER |
| USB-ETHERNET-AX88772B | 制造商:Olimex 功能描述:USB ETH ADAPTOR OLINUXINO |
| USB-EVAL | 功能描述:界面开发工具 USB products evalua- tion board unpopultd RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| USBEX02 | 制造商:Distributed By MCM 功能描述:15' USB 2.0 Active Extension Cable |
| USBEXT-150 | 制造商:DigitHead Inc 功能描述:USB EXTENDER 150' |
发布紧急采购，3分钟左右您将得到回复。