- 您现在的位置：买卖IC网 > PDF目录297788 > W9464G2IB-4 (WINBOND ELECTRONICS CORP) 512K X 32 DDR DRAM, 0.6 ns, PBGA144 PDF资料下载
参数资料
| 型号： | W9464G2IB-4 |
| 厂商： | WINBOND ELECTRONICS CORP |
| 元件分类： | DRAM |
| 英文描述： | 512K X 32 DDR DRAM, 0.6 ns, PBGA144 |
| 封装： | 12 X 12 MM, 1.40 MM HEIGHT, ROHS COMPLIANT, LFBGA-144 |
| 文件页数： | 4/49页 |
| 文件大小： | 886K |
| 代理商： | W9464G2IB-4 |
第1页第2页第3页当前第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页
W9464G2IB
Publication Release Date: Aug. 06, 2009
- 12 -
Revision A01
1) READA
≥ tRAS (min) – (BL/2) x tCK
Internal precharge operation begins after BL/2 cycle from Read with Auto-precharge command.
2) tRCD(min)
≤ READA < tRAS(min) – (BL/2) x tCK
Data can be read with shortest latency, but the internal Precharge operation does not begin until
after tRAS (min) has completed.
This command must not be interrupted by any other command.
7.2.8
Mode Register Set Command
( RAS = “L”, CAS = “L”, WE = “L”, BA0 = “L”, BA1 = “L”, A0 to A10 = Register Data)
The Mode Register Set command programs the values of CAS Latency, Addressing Mode, Burst
Length and DLL reset in the Mode Register. The default values in the Mode Register after power-
up are undefined, therefore this command must be issued during the power-up sequence. Also,
this command can be issued while all banks are in the idle state. Refer to the table for specific
codes.
7.2.9
Extended Mode Register Set Command
( RAS = “L”, CAS = “L”, WE = “L”, BA0 = “H”, BA1 = “L”, A0 to A10 = Register data)
The Extended Mode Register Set command can be implemented as needed for function
extensions to the standard (SDR-SDRAM). Currently the only available mode in EMRS is DLL
enable/disable, decoded by A0. The default value of the extended mode register is not defined;
therefore this command must be issued during the power-up sequence for enabling DLL. Refer to
the table for specific codes.
7.2.10 No-Operation Command
( RAS = “H”, CAS = “H”, WE = “H”)
The No-Operation command simply performs no operation (same command as Device Deselect).
7.2.11
Burst Read Stop Command
( RAS = “H”, CAS = “H”, WE = “L”)
The Burst stop command is used to stop the burst operation. This command is only valid during a
Burst Read operation.
7.2.12 Device Deselect Command
( CS = “H”)
The Device Deselect command disables the command decoder so that the RAS , CAS ,
WE
and Address inputs are ignored. This command is similar to the No-Operation command.
7.2.13
Auto Refresh Command
( RAS = “L”, CAS = “L”, WE = “H”, CKE = “H”, BA0, BA1, A0 to A10 = Don’t Care)
AUTO REFRESH is used during normal operation of the DDR SDRAM and is analogous to CAS–
BEFORE–RAS (CBR) refresh in previous DRAM types. This command is non-persistent, so it
must be issued each time a refresh is required.
The refresh addressing is generated by the internal refresh controller. This makes the address
bits ”Don’t Care” during an AUTO REFRESH command. The DDR SDRAM requires AUTO RE-
相关PDF资料 |
PDF描述 |
|---|---|
| WCMA2016U4X | 128K x 16 STATIC RAM |
| WCMA2016U4X-FF70 | 128K x 16 STATIC RAM |
| WDPI-3425J3525J-12 | 3425 MHz(Tx), 3525 MHz(Rx), DUPLEXER |
| WE-256K8-150CM | 256K X 8 EEPROM 5V, 150 ns, CDIP32 |
| WED3DG6418V10D1I | 16M X 64 SYNCHRONOUS DRAM MODULE, DMA144 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| W9464G6IB | 制造商:WINBOND 制造商全称:Winbond 功能描述:1M × 4 BANKS × 16 BITS DDR SDRAM |
| W9464G6IH | 制造商:WINBOND 制造商全称:Winbond 功能描述:1M ?? 4 BANKS ?? 16 BITS DDR SDRAM |
| W9464G6JH | 制造商:WINBOND 制造商全称:Winbond 功能描述:1M ? 4 BANKS ? 16 BITS DDR SDRAM |
| W9464G6JH-4 | 制造商:Winbond Electronics Corp 功能描述:IC DDR SDRAM 64M 200MHZ 66TSOP |
| W9464G6JH-5 | 制造商:Winbond Electronics Corp 功能描述:64MBIT DDRI 制造商:Winbond Electronics Corp 功能描述:IC DDR SDRAM 64M 200MHZ 66TSOP |
发布紧急采购，3分钟左右您将得到回复。