参数资料
| 型号： | XR16M698IQ100-F |
| 厂商： | Exar Corporation |
| 文件页数： | 10/58页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 32B OCTAL 100QFP |
| 标准包装： | 66 |
| 特点： | * |
| 通道数： | 8 |
| FIFO's： | 32 字节 |
| 规程： | RS485 |
| 电源电压： | 1.62 V ~ 3.63 V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 100-BQFP |
| 供应商设备封装： | 100-QFP（14x20） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页
XR16M698
18
1.62V TO 3.63V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO
REV. 1.0.0
2.11
Auto Xon/Xoff (Software) Flow Control
When software flow control is enabled (See Table 18), the 698 compares one or two sequential receive data
characters with the programmed Xon-1,2 or Xoff-1,2 character value(s). If receive character(s) (RX) match the
programmed Xoff-1,2 value(s), the 698 will halt transmission (TX) as soon as the current character has
completed transmission. When a match occurs, the Xoff (if enabled via IER bit-5) flag will be set and the
interrupt output pin will be activated. Following a suspension due to a match of the Xoff character(s), the 698
will monitor the receive data stream for a match to the Xon-1,2 character(s). If a match is found, the 698 will
resume operation and clear the flags (ISR bit-4).
Reset initially sets the contents of the Xon1, Xon2, Xoff1 and Xoff2 flow control registers to ’0’. Following reset,
any desired Xon/Xoff value can be used for software flow control. Different conditions can be set to detect Xon/
Xoff characters (See Table 18) and suspend/resume transmissions. When double 8-bit Xon/Xoff characters
are selected, the 698 compares two consecutive receive characters with two software flow control 8-bit values
(Xon1, Xon2, Xoff1, Xoff2) and controls TX transmissions accordingly. Under the above described flow control
mechanisms, flow control characters are not placed (stacked) in the user accessible RX data buffer or FIFO.
In the event that the receive buffer is overfilling and flow control needs to be executed, the 698 automatically
sends an Xoff message (when enabled) via the serial TX output to the remote modem. The 698 sends the Xoff-
1,2 characters two character times (= time taken to send two characters at the programmed baud rate) after
the receive FIFO crosses the programmed trigger level. To clear this condition, the 698 will transmit the
programmed Xon-1,2 characters as soon as receive FIFO is less than one trigger level below the programmed
trigger level. Table 7 below explains this.
TABLE 7: AUTO XON/XOFF (SOFTWARE) FLOW CONTROL
RX TRIGGER LEVEL
INT PIN ACTIVATION
XOFF CHARACTER(S) SENT
(CHARACTERS IN RX FIFO)
XON CHARACTER(S) SENT
(CHARACTERS IN RX FIFO)
8
8*
0
16
16*
8
24
24*
16
28
28*
24
* After the trigger level is reached, an xoff character is sent after a short span of time (= time required to send 2 characters);
for example, after 2.083ms has elapsed for 9600 baud and 10-bit word length setting.
2.12
Special Character Detect
A special character detect feature is provided to detect an 8-bit character when bit-5 is set in the Enhanced
Feature Register (EFR). When this character (Xoff2) is detected, it will be placed in the FIFO along with normal
incoming RX data. The 698 compares each incoming receive character with Xoff-2 data. If a match exists, the
received data will be transferred to FIFO and ISR bit-4 will be set to indicate detection of special character.
Although the Internal Register Table shows Xon, Xoff Registers with 8 bits of character information, the actual
number of bits is dependent on the programmed word length. Line Control Register (LCR) bits 0-1 defines the
number of character bits, i.e., either 5 bits, 6 bits, 7 bits, or 8 bits. The word length selected by LCR bits 0-1
also determines the number of bits that will be used for the special character comparison. Bit-0 in the Xon, Xoff
Registers corresponds to the LSB bit for the receive character.
相关PDF资料 |
PDF描述 |
|---|---|
| XR16M770IL32-F | IC UART FIFO 64B 32QFN |
| XR16M780IM48-F | IC UART FIFO 64B 48TQFP |
| XR16M781IL32-F | IC UART FIFO 64B 32QFN |
| XR16M890IM48TR-F | IC UART TXRX 128 BYTE 48TQFP |
| XR16V2550IL-F | IC UART FIFO 16B DUAL 32QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR16M698IQ100TR-F | 制造商:Exar Corporation 功能描述:UART 8-CH 32Byte FIFO 1.8V/2.5V/3.3V 100-Pin PQFP T/R 制造商:Exar Corporation 功能描述:XR16M698IQ100TR-F |
| XR16M752 | 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO |
| XR16M752_09 | 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO |
| XR16M752IL-0B-EB | 功能描述:UART 接口集成电路 Supports 16M752 32L QFN, PCI Interface RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16M752IL32 | 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO |
发布紧急采购，3分钟左右您将得到回复。