参数资料
| 型号： | XR16M698IQ100-F |
| 厂商： | Exar Corporation |
| 文件页数： | 14/58页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 32B OCTAL 100QFP |
| 标准包装： | 66 |
| 特点： | * |
| 通道数： | 8 |
| FIFO's： | 32 字节 |
| 规程： | RS485 |
| 电源电压： | 1.62 V ~ 3.63 V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 100-BQFP |
| 供应商设备封装： | 100-QFP（14x20） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页
XR16M698
21
REV. 1.0.0
1.62V TO 3.63V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO
2.15
Sleep Mode with Auto Wake-Up
The 698 supports low voltage system designs, hence, a sleep mode is included to reduce its power
consumption when the chip is not actively used.
All of these conditions must be satisfied for the 698 to enter sleep mode:
■ no interrupts pending for all 8 channels of the 698 (ISR bit-0 = 1)
■ SLEEP register = 0xFF
■ modem inputs are not toggling (MSR bits 0-3 = 0)
■ RX input pin of all 8 channels are idling HIGH
The 698 stops its crystal oscillator to conserve power in the sleep mode. User can check the XTAL2 pin for no
clock output as an indication that the device has entered the sleep mode.
The 698 resumes normal operation by any of the following:
■ a receive data start bit transition (HIGH to LOW)
■ a data byte is loaded to the transmitter, THR or FIFO
■ a change of logic state on any of the modem or general purpose serial inputs: CTS#, DSR#, CD#, RI#
If the 698 is awakened by any one of the above conditions, it will generate an interrupt. If the interrupt for the
event that woke up the 698 is not enabled, then a special wake-up interrupt occurs where reading the interrupt
status register will return a "no interrupt" indication. For example, there is a change of state on the CTS# input
that wakes up the 698, but the MSR interrupt is not enabled. Reading the interrupt status register will return a
value indicating that there are no pending interrupts and will clear the wake-up interrupt.
The 698 will return to the sleep mode automatically after all interrupting conditions have been serviced and
cleared. If the 698 is awakened by the modem inputs, a read to the MSR is required to reset the modem inputs.
In any case, the sleep mode will not be entered while an interrupt is pending in any channel. The 698 will stay
in the sleep mode of operation until it is disabled by setting SLEEP = 0x00.
A word of caution: owing to the starting up delay of the crystal oscillator after waking up from sleep mode, the
first few receive characters may be lost. The number of characters lost during the restart also depends on your
operating data rate. More characters are lost when operating at higher data rate.
相关PDF资料 |
PDF描述 |
|---|---|
| XR16M770IL32-F | IC UART FIFO 64B 32QFN |
| XR16M780IM48-F | IC UART FIFO 64B 48TQFP |
| XR16M781IL32-F | IC UART FIFO 64B 32QFN |
| XR16M890IM48TR-F | IC UART TXRX 128 BYTE 48TQFP |
| XR16V2550IL-F | IC UART FIFO 16B DUAL 32QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR16M698IQ100TR-F | 制造商:Exar Corporation 功能描述:UART 8-CH 32Byte FIFO 1.8V/2.5V/3.3V 100-Pin PQFP T/R 制造商:Exar Corporation 功能描述:XR16M698IQ100TR-F |
| XR16M752 | 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO |
| XR16M752_09 | 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO |
| XR16M752IL-0B-EB | 功能描述:UART 接口集成电路 Supports 16M752 32L QFN, PCI Interface RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16M752IL32 | 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO |
发布紧急采购，3分钟左右您将得到回复。