参数资料
| 型号： | XR16M698IQ100-F |
| 厂商： | Exar Corporation |
| 文件页数： | 36/58页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO 32B OCTAL 100QFP |
| 标准包装： | 66 |
| 特点： | * |
| 通道数： | 8 |
| FIFO's： | 32 字节 |
| 规程： | RS485 |
| 电源电压： | 1.62 V ~ 3.63 V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 100-BQFP |
| 供应商设备封装： | 100-QFP（14x20） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页当前第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页
XR16M698
41
REV. 1.0.0
1.62V TO 3.63V HIGH PERFORMANCE OCTAL UART WITH 32-BYTE FIFO
LSR[6]: Transmitter Empty Flag
This bit is the Transmitter Empty indicator. This bit is set to a logic 1 whenever both the transmit FIFO (or THR,
in non-FIFO mode) and the transmit shift register (TSR) are both empty. It is set to logic 0 whenever either the
TX FIFO or TSR contains a data character.
LSR[5]: Transmit FIFO Empty Flag
This bit is the Transmit FIFO Empty indicator. This bit indicates that the transmitter is ready to accept a new
character for transmission. This bit is set to a logic 1 when the last data byte is transferred from the transmit
FIFO to the transmit shift register. The bit is reset to logic 0 as soon as a data byte is loaded into the transmit
FIFO. In the non-FIFO mode this bit is set when the transmit holding register (THR) is empty; it is cleared when
at a byte is written to the THR.
LSR[4]: Receive Break Flag
Logic 0 = No break condition (default).
Logic 1 = The receiver received a break signal (RX was a logic 0 for one character frame time). In the FIFO
mode, only one break character is loaded into the FIFO. The break indication remains until the RX input
returns to the idle condition, “mark” or logic 1.
LSR[3]: Receive Data Framing Error Flag
Logic 0 = No framing error (default).
Logic 1 = Framing error. The receive character did not have a valid stop bit(s). This error is associated with
the character available for reading in RHR.
LSR[2]: Receive Data Parity Error Flag
Logic 0 = No parity error (default).
Logic 1 = Parity error. The receive character in RHR (top of the FIFO) does not have correct parity
information and is suspect. This error is associated with the character available for reading in RHR.
LSR[1]: Receiver Overrun Flag
Logic 0 = No overrun error (default).
Logic 1 = Overrun error. A data overrun error condition occurred in the receive shift register. This happens
when additional data arrives while the FIFO is full. In this case the previous data in the receive shift register
is overwritten. Note that under this condition the data byte in the receive shift register is not transferred into
the FIFO, therefore the data in the FIFO is not corrupted by the error.
LSR[0]: Receive Data Ready Indicator
Logic 0 = No data in receive holding register or FIFO (default).
Logic 1 = Data has been received and is saved in the receive holding register or FIFO.
4.9
Modem Status Register (MSR) - Read Only
This register provides the current state of the modem interface signals, or other peripheral device that the
UART is connected. Lower four bits of this register are used to indicate the changed information. These bits
are set to a logic 1 whenever a signal from the modem changes state. These bits may be used as general
purpose inputs/outputs when they are not used with modem signals.
MSR[7]: CD Input Status
Normally this bit is the complement of the CD# input. In the loopback mode this bit is equivalent to bit-3 in the
MCR register. The CD# input may be used as a general purpose input when the modem interface is not used.
相关PDF资料 |
PDF描述 |
|---|---|
| XR16M770IL32-F | IC UART FIFO 64B 32QFN |
| XR16M780IM48-F | IC UART FIFO 64B 48TQFP |
| XR16M781IL32-F | IC UART FIFO 64B 32QFN |
| XR16M890IM48TR-F | IC UART TXRX 128 BYTE 48TQFP |
| XR16V2550IL-F | IC UART FIFO 16B DUAL 32QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR16M698IQ100TR-F | 制造商:Exar Corporation 功能描述:UART 8-CH 32Byte FIFO 1.8V/2.5V/3.3V 100-Pin PQFP T/R 制造商:Exar Corporation 功能描述:XR16M698IQ100TR-F |
| XR16M752 | 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO |
| XR16M752_09 | 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO |
| XR16M752IL-0B-EB | 功能描述:UART 接口集成电路 Supports 16M752 32L QFN, PCI Interface RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR16M752IL32 | 制造商:EXAR 制造商全称:EXAR 功能描述:HIGH PERFORMANCE DUART WITH 64-BYTE FIFO |
发布紧急采购，3分钟左右您将得到回复。