- 您现在的位置：买卖IC网 > PDF目录300164 > ZL50112GAG2 (ZARLINK SEMICONDUCTOR INC) SPECIALTY TELECOM CIRCUIT, PBGA552 PDF资料下载
参数资料
| 型号： | ZL50112GAG2 |
| 厂商： | ZARLINK SEMICONDUCTOR INC |
| 元件分类： | 通信及网络 |
| 英文描述： | SPECIALTY TELECOM CIRCUIT, PBGA552 |
| 封装： | 35 X 35 MM, 1.27 MM, LEAD FREE, PLASTIC, BGA-552 |
| 文件页数： | 89/113页 |
| 文件大小： | 1923K |
| 代理商： | ZL50112GAG2 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页当前第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页
ZL50110/11/12/14
Data Sheet
77
Zarlink Semiconductor Inc.
8.3
Locking Mode Reference Switching
When the reference source the DPLL is currently locking to becomes invalid, the DPLL’s response depends on
which one of the failure detect modes has been chosen: autodetect, forced primary, or forced secondary. One of
these failure detect modes must be chosen via the FDM1:0 bits of the DOM register. After a device reset via the
SYSTEM_RESET pin, the autodetect mode is selected.
In autodetect mode (automatic reference switching) if both references are valid the DPLL will synchronise to the
preferred reference. If the preferred reference becomes unreliable, the DPLL continues driving its output clock in a
stable holdover state until it makes a switch to the backup reference. If the preferred reference recovers, the DPLL
makes a switch back to the preferred reference. If necessary, the switch back can be prevented by changing the
preferred reference using the REFSEL bit in the DOM register, after the switch to the backup reference has
occurred.
If both references are unreliable, the DPLL will drive its output clock using the stable holdover values until one of
the references becomes valid.
In forced primary mode, the DPLL will synchronise to the primary reference only. The DPLL will not switch to the
secondary reference under any circumstances including the loss of the primary reference. In this condition, the
DPLL remains in holdover mode until the primary reference recovers. Similarly in forced secondary mode, the
DPLL will synchronise to the secondary reference only, and will not switch to the primary reference. Again, a failure
of the secondary reference will cause the DPLL to enter holdover mode, until such time as the secondary reference
recovers. The choice of preferred reference has no effect in these modes.
When a conventional PLL is locked to its reference, there is no phase difference between the input reference and
the PLL output. For the DPLL, the input references can have any phase relationship between them. During a
reference switch, if the DPLL output follows the phase of the new reference, a large phase jump could occur. The
phase jump would be transferred to the TDM outputs. The DPLL’s MTIE (Maximum Time Interval Error) feature
preserves the continuity of the DPLL output so that it appears no reference switch had occurred. The MTIE circuit is
not perfect however, and a small Time Interval Error is still incurred per reference switch. To align the DPLL output
clock to the nearest edge of the selected input reference, the MTIE reset bit (MRST bit in the DOM register) can be
used.
Unlike some designs, switching between references which are at different nominal frequencies do not require
intervention such as a system reset.
8.4
Locking Range
The locking range is the input frequency range over which the DPLL must be able to pull into synchronization and to
maintain the synchronization. The locking range is programmable up to ±372 ppm.
Note that the locking range relates to the system clock frequency. If the external oscillator has a tolerance of
-100 ppm, and the locking range is programmed to ±200 ppm, the actual locking range is the programmed value
shifted by the system clock tolerance to become -300 ppm to +100 ppm.
8.5
Locking Time
The Locking Time is the time it takes the synchroniser to phase lock to the input signal. Phase lock occurs when the
input and output signals are not changing in phase with respect to each other (not including jitter).
Locking time is very difficult to determine because it is affected by many factors including:
initial input to output phase difference
initial input to output frequency difference
DPLL Loop Filter
DPLL Limiter (phase slope)
相关PDF资料 |
PDF描述 |
|---|---|
| ZL50112GAG | SPECIALTY TELECOM CIRCUIT, PBGA552 |
| ZL50114GAG2 | SPECIALTY TELECOM CIRCUIT, PBGA552 |
| ZL50114GAG | SPECIALTY TELECOM CIRCUIT, PBGA552 |
| ZL50232GD | DATACOM, ISDN ECHO CANCELLER, PBGA208 |
| ZL50233/GDG | DATACOM, ISDN ECHO CANCELLER, PBGA208 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ZL50114 | 制造商:ZARLINK 制造商全称:Zarlink Semiconductor Inc 功能描述:128, 256, 512 and 1024 Channel CESoP Processors |
| ZL50114GAG | 制造商:Microsemi Corporation 功能描述:CESOP PROCESSOR 552BGA - Trays 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC CESOP PROCESSOR 128CH 552PBGA 制造商:Microsemi Corporation 功能描述:IC CESOP PROCESSOR 128CH 552PBGA |
| ZL50114GAG2 | 制造商:Microsemi Corporation 功能描述:CESOP PROCESSOR 552BGA - Trays 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC CESOP PROCESSOR 128CH 552PBGA 制造商:Microsemi Corporation 功能描述:IC CESOP PROCESSOR 128CH 552PBGA |
| ZL50115 | 制造商:ZARLINK 制造商全称:Zarlink Semiconductor Inc 功能描述:32, 64 and 128 Channel CESoP Processors |
| ZL50115GAG | 制造商:Microsemi Corporation 功能描述:SWIT FABRIC 1K X 1K 1.8V/3.3V 324BGA - Trays 制造商:Microsemi Corporation 功能描述:IC CESOP PROCESSOR 32CH 324PBGA |
发布紧急采购，3分钟左右您将得到回复。