- 您现在的位置：买卖IC网 > PDF目录68811 > 71M6542G-IGT/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PQFP100 PDF资料下载
参数资料
| 型号： | 71M6542G-IGT/F |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 封装： | LEAD FREE, LQFP-100 |
| 文件页数： | 118/165页 |
| 文件大小： | 2208K |
| 代理商： | 71M6542G-IGT/F |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页当前第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页
56
2008–2011 Teridian Semiconductor Corporation
v1.1
2.5.5
71M654x Temperature Sensor
The 71M654x includes an on-chip temperature sensor for determining the temperature of its bandgap
reference. The primary use of the temperature data is to determine the magnitude of compensation
required to offset the thermal drift in the system for the compensation of current, voltage and energy
RTC Temperature Compensation on page 53.
Unlike earlier generation Teridian SoCs, the 71M654x does not use the ADC to read the temperature
sensor. Instead, it uses a technique that is operational in SLP and LCD mode, as well as BRN and MSN
modes. This means that the temperature sensor can be used to compensate for the frequency variation
of the crystal, even in SLP mode while the MPU is halted. See 2.5.4.4 RTC Temperature Compensation
on page 53.
In MSN and BRN modes, the temperature sensor is awakened on command from the MPU by setting the
TEMP_START (I/O RAM 0x28B4[6]) control bit. The MPU must wait for the TEMP_START bit to clear before
reading STEMP[10:0] and before setting the TEMP_START bit once again. In SLP and LCD modes, it is
awakened at a regular rate set by TEMP_PER[2:0] (I/O RAM 0x28A0[2:0]).
The result of the temperature measurement can be read from the two I/O RAM locations STEMP[10:3]
(I/O RAM 0x2881) and STEMP[2:0] (I/O RAM 0x2882[7:5]). Note that both of these I/O RAM locations must
be read and properly combined to form the STEMP[10:0] 11-bit value (see STEMP in Table 46). The
resulting 11-bit value is in 2’s complement form and ranges from -1024 to +1023 (decimal). The equations
below are used to calculate the sensed temperature from the 11-bit STEMP[10:0] reading.
The equations below are used to calculate the sensed temperature. The first equation applies when the
71M654x is in MSN mode and TEMP_PWR = 1. The second equation applies when the 71M654x is in
BRN mode, and in this case, the TEMP_PWR and TEMP_BSEL bits must both be set to the same value, so
that the battery that supplies the temperature sensor is also the battery that is measured and reported in
BSENSE. Thus, the second equation requires reading STEMP and BSENSE. In the second equation,
BSENSE (the sensed battery voltage) is used to obtain a more accurate temperature reading when the IC
is in BRN mode.
For the 71M654x in MSN Mode (with TEMP_PWR = 1):
22
325
.
0
)
(
+
=
°
STEMP
C
Temp
For the 71M654x in BRN Mode, (with TEMP_PWR=TEMP_BSEL):
9
.
40
584
.
0
00208
.
0
325
.
0
)
(
2
+
+
=
BSENSE
STEMP
C
Temp
o
Table 46 shows the I/O RAM registers used for temperature and battery measurement.
If TEMP_PWR selects VBAT_RTC when the battery is nearly discharged, the temperature
measurement may not finish. In this case, firmware may complete the measurement by selecting
V3P3D (TEMP_PWR = 1).
Table 46: I/O RAM Registers for Temperature and Battery Measurement
Name
Location
Rst
Wk
Dir
Description
TBYTE_BUSY
28A0[3]
0
R
Indicates that hardware is still writing the 0x28A0
byte. Additional writes to this byte are locked out
while it is one. Write duration could be as long as 6 ms.
TEMP_PER[2:0]
28A0[2:0]
0
–
R/W
Sets the period between temperature measurements.
Automatic measurements can be enabled in any
mode (MSN, BRN, LCD, or SLP).
TEMP_PER
Time
0
Manual updates (see TEMP_START)
1-6
2 ^ (3+TEMP_PER) (seconds)
7
Continuous
相关PDF资料 |
PDF描述 |
|---|---|
| 71M6541G-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| 71M6541F-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| 71M6543F-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543H-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543F-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 71M6542G-IGTR/F | 制造商:Maxim Integrated Products 功能描述:- Tape and Reel |
| 71M6542GT-IGT/F | 制造商:Maxim Integrated Products 功能描述:1-PHASE, 128KB, PRES TEMP SENSOR - Bulk |
| 71M6542GT-IGTR/F | 制造商:Maxim Integrated Products 功能描述:1-PHASE, 128KB, PRES TEMP SENSOR - Tape and Reel |
| 71M6543F | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Selectable Gain of 1 or 8 for One Current Energy Meter ICs Metrology Compensation |
| 71M6543F-DB | 功能描述:开发板和工具包 - 8051 71M6543 Eval Kit RoHS:否 制造商:Silicon Labs 产品:Development Kits 工具用于评估:C8051F960, Si7005 核心: 接口类型:USB 工作电源电压: |
发布紧急采购，3分钟左右您将得到回复。