- 您现在的位置：买卖IC网 > PDF目录68811 > 71M6542G-IGT/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PQFP100 PDF资料下载
参数资料
| 型号： | 71M6542G-IGT/F |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 封装： | LEAD FREE, LQFP-100 |
| 文件页数： | 135/165页 |
| 文件大小： | 2208K |
| 代理商： | 71M6542G-IGT/F |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页当前第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页
v1.1
2008–2011 Teridian Semiconductor Corporation
71
Table 60: EECTRL Bits for 2-pin Interface
Status
Bit
Name
Read/
Write
Reset
State
Polarity
Description
7
ERROR
R
0
Positive
1 when an illegal command is received.
6
BUSY
R
0
Positive
1 when serial data bus is busy.
5
RX_ACK
R
1
Positive
1 indicates that the EEPROM sent an ACK bit.
4
TX_ACK
R
1
Positive
1 indicates that an ACK bit has been sent to the
EEPROM.
3:0
CMD[3:0]
W
0000
Positive
CMD[3:0]
Operation
0000
No-op command.
0010
Receive a byte from the EEPROM
and send ACK.
0011
Transmit a byte to the EEPROM.
0101
Issue a STOP sequence.
0110
Receive the last byte from the
EEPROM and do not send ACK.
1001
Issue a START sequence.
Others
No operation, set the ERROR bit.
The EEPROM interface can also be operated by controlling the DIO2 and DIO3 pins directly. The
direction of the DIO line can be changed from input to output and an output value can be written
with a single write operation, thus avoiding collisions (see Table 15 Port Registers (SEGDIO0-15)).
Therefore, no resistor is required in series SDATA to protect against collisions.
2.5.9.2 Three-wire (-Wire) EEPROM Interface with Single Data Pin
A 500 kHz three-wire interface, using SDATA, SDCK, and a DIO pin for CS is available. The interface is
selected by setting DIO_EEX[1:0] = 10. The EECTRL bits when the three-wire interface is selected are
shown in Table 61. When EECTRL is written, up to 8 bits from EEDATA are either written to the EEPROM
or read from the EEPROM, depending on the values of the EECTRL bits.
2.5.9.3 Three-wire (-Wire/SPI) EEPROM Interface with Separate Di/DO Pins
If DIO_EEX[1:0]=11, the three-wire interface is the same as above, except DI and DO are separate pins.
In this case, SEGDIO3 becomes DO and SEGDIO8 becomes DI. The timing diagrams are the same as
for DIO_EEX[1:0]=10 except that all output data appears on DO and all input data is expected on DI. In
this mode, DI is ignored while data is being received on DO. This mode is compatible with SPI modes 0,0
and 1,1 where data is shifted out on the falling edge of the clock and is strobed in on the rising edge of
the clock.
Table 61: EECTRL Bits for the 3-wire Interface
Control
Bit
Name
Read/
Write
Description
7
WFR
W
Wait for Ready. If this bit is set, the trailing edge of BUSY is delayed until
a rising edge is seen on the data line. This bit can be used during the
last byte of a Write command to cause the INT5 interrupt to occur when
the EEPROM has finished its internal write sequence. This bit is ignored
if Hi-Z=0.
6
BUSY
R
Asserted while the serial data bus is busy. When the BUSY bit falls, an
INT5 interrupt occurs.
5
HiZ
W
Indicates that the SD signal is to be floated to high impedance immediately
after the last SDCK rising edge.
相关PDF资料 |
PDF描述 |
|---|---|
| 71M6541G-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| 71M6541F-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP64 |
| 71M6543F-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543H-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543F-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 71M6542G-IGTR/F | 制造商:Maxim Integrated Products 功能描述:- Tape and Reel |
| 71M6542GT-IGT/F | 制造商:Maxim Integrated Products 功能描述:1-PHASE, 128KB, PRES TEMP SENSOR - Bulk |
| 71M6542GT-IGTR/F | 制造商:Maxim Integrated Products 功能描述:1-PHASE, 128KB, PRES TEMP SENSOR - Tape and Reel |
| 71M6543F | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Selectable Gain of 1 or 8 for One Current Energy Meter ICs Metrology Compensation |
| 71M6543F-DB | 功能描述:开发板和工具包 - 8051 71M6543 Eval Kit RoHS:否 制造商:Silicon Labs 产品:Development Kits 工具用于评估:C8051F960, Si7005 核心: 接口类型:USB 工作电源电压: |
发布紧急采购，3分钟左右您将得到回复。