- 您现在的位置：买卖IC网 > PDF目录20610 > 71M6545-IGTR/F (Maxim Integrated)IC ENERGY METER 3PHASE 64LQFP PDF资料下载
参数资料
| 型号： | 71M6545-IGTR/F |
| 厂商： | Maxim Integrated |
| 文件页数： | 52/133页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METER 3PHASE 64LQFP |
| 标准包装： | 1,500 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页当前第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页
71M6545/71M6545H Data Sheet
The 8-bit NV RAM content pointed to by the address is added as a 2’s complement value to 0x40000,
the nominal value of 4* RTC_P[16:0] + RTC_Q[1:0] .
Refer to 2.5.4.3 RTC Rate Control for information on the rate adjustments performed by registers
RTC_P[16:0] and RTC_Q[1:0] . The 8-bit values loaded in to NV RAM must be scaled correctly to produce
rate adjustments that are consistent with the equations given in 2.5.4.3 RTC Rate Control for RTC_P[16:0]
and RTC_Q[1:0]. Note that the sum of the looked-up 8-bit 2’s complement value and 0x40000 form a 19-
bit value, which is equal to 4* RTC_P[16:0] + RTC_Q[1:0], as shown in Figure 13. The output of the
Temperature Compensation is automatically loaded into the RTC_P[16:0] and RTC_Q[1:0] locations after
each look-up and summation operation.
STEMP
10+S
>>2
8+S
LIMIT
-256
-64
63
-64
63
255
6+S
Look Up
RAM
ADDR
Q
7+S
Σ
19
4*RTC_P+RTC_Q
19
0x40000
Figure 13: Automatic Temperature Compensation
As mentioned above, the STEMP[10:0] digital temperature values are scaled such that the
corresponding NV RAM addresses are equal to STEMP[10:0] /4 (limited in the range of -64 to +63). See
2.5.5 71M6545/H Temperature Sensor on page 53 for the equations to calculate temperature in degrees °C
from the STEMP[10:0] reading.
For proper operation, the MPU has to load the lookup table with values that reflect the crystal properties
with respect to temperature, which is typically done once during initialization. Since the lookup table is
not directly addressable, the MPU uses the following procedure to load the NV RAM table:
1. Set the LKPAUTOI bit ( I/O RAM 0x2887[7] ) to enable address auto-increment.
2. Write zero into the I/O RAM register LKPADDR[6:0] ( I/O RAM 0x2887[6:0] ).
3. Write the 8-bit datum into I/O RAM register LKPDAT ( I/O RAM 0x2888 ).
4. Set the LKP_WR bit ( I/O RAM 0x2889[0 ] ) to write the 8-bit datum into NV_RAM
5.
Wait for LKP_WR to clear ( LKP_WR auto-clears when the data has been copied to NV RAM).
6. Repeat steps 3 through 5 until all data has been written to NV RAM.
The NV RAM table can also be read by writing a 1 into the LKP_RD bit ( I/O RAM 0x2889[1] ). The process
of reading from and writing to the NV RAM is accelerated by setting the LKPAUTOI bit ( I/O RAM 0x2887[7] ).
When LKPAUTOI is set, LKPADDR[6:0] ( I/O RAM 0x2887[6:0] ) auto-increments every time LKP_RD or
LKP_WR is pulsed. It is also possible to perform random access of the NV RAM by writing a 0 to the
LKPAUTOI bit and loading the desired address into LKPADDR[6:0] .
If the oscillator temperature compensation feature is not being used, it is possible to use the NV
RAM storage area as ordinary battery-backed NV storage space using the procedure described
above to read and write NV RAM data. In this case, the OSC_COMP bit ( I/O RAM 0x28A0[5] ) is
reset to disable the automatic oscillator temperature compensation feature.
2.5.4.5 RTC Interrupts
The RTC generates interrupts each second and each minute. These interrupts are called RTC_1SEC
and RTC_1MIN . In addition, the RTC functions as an alarm clock by generating an interrupt when the
minutes and hours registers both equal their respective target counts. The alarm clock interrupt is called
RTC_T. All three interrupts appear in the MPU’s external interrupt 6. See Table 31 in the interrupt section
for the enable bits and flags for these interrupts.
The minute and hour target registers are listed in Table 42 .
52
v2
相关PDF资料 |
PDF描述 |
|---|---|
| T95S224M035LZAL | CAP TANT 0.22UF 35V 20% 1507 |
| GBC12DCSN-S288 | CONN EDGECARD 24POS .100 EXTEND |
| 78M6612-M/F/P2 | IC PWR MEASUREMENT AC 68SQFN |
| V48C28H75BL2 | CONVERTER MOD DC/DC 28V 75W |
| ISL6613IRZ-T | IC MOSFET DRVR SYNC BUCK 10-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 71M6545T-IGT/F | 制造商:Maxim Integrated Products 功能描述:METROLOGY PROCESSORS - Rail/Tube |
| 71M6545T-IGTR/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE AFE, 32KB FLASH, PRES TEMP SENSOR - Tape and Reel |
| 71M6601 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:On-Chip Temperature Sensor Enables Localized Digital Temperature On-Chip Power Monitoring |
| 71M6601-IF | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:On-Chip Temperature Sensor Enables Localized Digital Temperature On-Chip Power Monitoring |
| 71M6601-IL | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:On-Chip Temperature Sensor Enables Localized Digital Temperature On-Chip Power Monitoring |
发布紧急采购，3分钟左右您将得到回复。