参数资料
型号: 71M6545-IGTR/F
厂商: Maxim Integrated
文件页数: 54/133页
文件大小: 0K
描述: IC ENERGY METER 3PHASE 64LQFP
标准包装: 1,500
系列: *
71M6545/71M6545H Data Sheet
Table 43: I/O RAM Registers for Temperature and Battery Measurement
Name
TBYTE_BUSY
TEMP_PER[2:0]
Location
28A0[3]
28A0[2:0]
Rst
0
0
Wk
0
Dir
R
R/W
Description
Indicates that hardware is still writing the 0x28A0
byte. Additional writes to this byte are locked out
while it is one. Write duration could be as long as 6 ms.
Sets the period between temperature measurements.
Automatic measurements can be enabled in any
mode (MSN and during ac power outages if the
VBAT_RTC voltage is within specification, as
supplied by a battery).
TEMP_PER Time
0 Manual updates (see TEMP_START )
1-6
7
2 ^ (3+ TEMP_PER ) (seconds)
Continuous
TEMP_BAT
TEMP_START
TEMP_PWR
28A0[4]
28B4[6]
28A0[6]
0
0
0
R/W
R/W
R/W
Causes the VBAT_RTC pin to be measured
whenever a temperature measurement is performed.
TEMP_PER[2:0] must be zero in order for TEMP_START
to function. If TEMP_PER[2:0] = 0, then setting
TEMP_START starts a temperature measurement.
This bit is ignored in SLP mode. Hardware clears
TEMP_START when the temperature measurement is
complete.
Selects the power source for the temperature sensor:
1 = V3P3D, 0 = VBAT_RTC. This bit is ignored in
SLP mode, where the temperature sensor is always
powered by VBAT_RTC.
Reserved
28A0[7]
0
R/W Must always be zero.
TEMP_TEST[1:0] 2500[1:0]
0
R/W
Test bits for the temperature monitor VCO.
TEMP_TEST must be 00 in regular operation. Any
other value causes the VCO to run continuously with
the control voltage described below.
TEMP_TEST Function
00
01
1X
Normal operation
Reserved for factory test
Reserved for factory test
STEMP[10:3]
STEMP[2:0]
2881[7:0]
2882[7:5]
R
R
The result of the temperature measurement.
The STEMP[10:0] value may be obtained in C with a
single 16-bit read and divide by 32 operation as
follows:
volatile int16_t xdata STEMP _at_0x2881;
fa = (float)(STEMP/32);
BSENSE[7:0]
BCURR
2885[7:0]
2704[3]
0
0
R
R/W
The result of the battery measurement.
Connects a 100 μA load to the battery (VBAT_RTC
pin).
2.5.6
71M6xx3 Temperature Sensor
The 71M6xx3 includes an on-chip temperature sensor for determining the temperature of its bandgap
reference. The primary use of the temperature data is to determine the magnitude of compensation
required to offset the thermal drift in the system for the compensation of the current measurement
performed by the71M6xx3. See the 71M6xxx Data Sheet for the equation to calculate temperature from the
71M6xx3 STEMP[10:0] reading. Also, see 4.5 Metrology Temperature Compensation on page 74 .
54
v2
相关PDF资料
PDF描述
T95S224M035LZAL CAP TANT 0.22UF 35V 20% 1507
GBC12DCSN-S288 CONN EDGECARD 24POS .100 EXTEND
78M6612-M/F/P2 IC PWR MEASUREMENT AC 68SQFN
V48C28H75BL2 CONVERTER MOD DC/DC 28V 75W
ISL6613IRZ-T IC MOSFET DRVR SYNC BUCK 10-DFN
相关代理商/技术参数
参数描述
71M6545T-IGT/F 制造商:Maxim Integrated Products 功能描述:METROLOGY PROCESSORS - Rail/Tube
71M6545T-IGTR/F 制造商:Maxim Integrated Products 功能描述:3-PHASE AFE, 32KB FLASH, PRES TEMP SENSOR - Tape and Reel
71M6601 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:On-Chip Temperature Sensor Enables Localized Digital Temperature On-Chip Power Monitoring
71M6601-IF 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:On-Chip Temperature Sensor Enables Localized Digital Temperature On-Chip Power Monitoring
71M6601-IL 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:On-Chip Temperature Sensor Enables Localized Digital Temperature On-Chip Power Monitoring