- 您现在的位置：买卖IC网 > PDF目录1986 > AD9258BCPZ-125 (Analog Devices Inc)IC ADC 14BIT 125MSPS DL 64LFCSP PDF资料下载
参数资料
| 型号： | AD9258BCPZ-125 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 30/44页 |
| 文件大小： | 0K |
| 描述： | IC ADC 14BIT 125MSPS DL 64LFCSP |
| 设计资源： | High Performance, Dual Channel IF Sampling Receiver (CN0140) |
| 标准包装： | 1 |
| 位数： | 14 |
| 采样率（每秒）： | 125M |
| 数据接口： | 串行 |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 788mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 64-LFCSP-VQ（9x9） |
| 包装： | 托盘 |
| 输入数目和类型： | 2 个差分，单极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页当前第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
AD9258
Rev. A | Page 36 of 44
HARDWARE INTERFACE
The pins described in Table 14 comprise the physical interface
between the user programming device and the serial port of the
AD9258. The SCLK pin and the CSB pin function as inputs
when using the SPI. The SDIO pin is bidirectional, functioning
as an input during write phases and as an output during
readback.
The SPI is flexible enough to be controlled by either FPGAs or
microcontrollers. One method for SPI configuration is
described in detail in the AN-812 Application Note, Micro-
controller-Based Serial Port Interface (SPI) Boot Circuit.
The SPI port should not be active during periods when the full
dynamic performance of the converter is required. Because the
SCLK signal, the CSB signal, and the SDIO signal are typically
asynchronous to the ADC clock, noise from these signals can
degrade converter performance. If the on-board SPI bus is used for
other devices, it may be necessary to provide buffers between
this bus and the AD9258 to prevent these signals from transi-
tioning at the converter inputs during critical sampling periods.
Some pins serve a dual function when the SPI is not being used.
When the pins are strapped to AVDD or ground during device
power-on, they are associated with a specific function. The
Digital Outputs section describes the strappable functions
supported on the AD9258.
CONFIGURATION WITHOUT THE SPI
In applications that do not interface to the SPI control registers,
the SDIO/DCS pin, the SCLK/DFS pin, the OEB pin, and the
PDWN pin serve as standalone CMOS-compatible control pins.
When the device is powered up, it is assumed that the user intends
to use the pins as static control lines for the duty cycle stabilizer,
output data format, output enable, and power-down feature
control. In this mode, the CSB chip select bar should be con-
nected to AVDD, which disables the serial port interface.
When the device is in SPI mode, the PDWN and OEB pins
remain active. For SPI control of output enable and power-down,
the OEB and PDWN pins should be set to their default states.
Table 15. Mode Selection
Pin
External
Voltage
Configuration
SDIO/DCS
AVDD (default)
Duty cycle stabilizer enabled
AGND
Duty cycle stabilizer disabled
SCLK/DFS
AVDD
Twos complement enabled
AGND (default)
Offset binary enabled
OEB
AVDD
Outputs in high impedance
AGND (default)
Outputs enabled
PDWN
AVDD
Chip in power-down or
standby
AGND (default)
Normal operation
SPI ACCESSIBLE FEATURES
Table 16 provides a brief description of the general features that
are accessible via the SPI. These features are described in detail
in the AN-877 Application Note, Interfacing to High Speed ADCs
via SPI. The AD9258 part-specific features are described in detail
following Table 17, the external memory map register table.
Table 16. Features Accessible Using the SPI
Feature Name
Description
Mode
Allows the user to set either power-down mode
or standby mode
Clock
Allows the user to access the DCS, set the
clock divider, set the clock divider phase, and
enable the sync
Offset
Allows the user to digitally adjust the
converter offset
Test I/O
Allows the user to set test modes to have
known data on output bits
Output Mode
Allows the user to set the output mode
including LVDS
Output Phase
Allows the user to set the output clock polarity
Output Delay
Allows the user to vary the DCO delay
VREF
Allows the user to set the reference voltage
相关PDF资料 |
PDF描述 |
|---|---|
| AD9259ABCPZRL7-50 | IC ADC 14BIT SRL 50MSPS 48LFCSP |
| AD9260ASZRL | IC ADC 16BIT 2.5MHZ 44MQFP |
| AD9262BCPZ-10 | IC ADC 16BIT 10MHZ 64LFCSP |
| AD9266BCPZRL7-20 | IC ADC 16BIT 20MSPS 32LFCSP |
| AD9269BCPZRL7-20 | IC ADC 16BIT 20MSPS DL 64LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9258BCPZ-1251 | 制造商:AD 制造商全称:Analog Devices 功能描述:14-Bit, 80 MSPS/105 MSPS/125 MSPS, 1.8 V Dual Analog-to-Digital Converter (ADC) |
| AD9258BCPZ-80 | 功能描述:模数转换器 - ADC Dual 14 bit 80 high SNR ADC RoHS:否 制造商:Analog Devices 通道数量: 结构: 转换速率: 分辨率: 输入类型: 信噪比: 接口类型: 工作电源电压: 最大工作温度: 安装风格: 封装 / 箱体: |
| AD9258BCPZ-801 | 制造商:AD 制造商全称:Analog Devices 功能描述:14-Bit, 80 MSPS/105 MSPS/125 MSPS, 1.8 V Dual Analog-to-Digital Converter (ADC) |
| AD9258BCPZRL7-105 | 功能描述:模数转换器 - ADC Dual 14 bit 105 highSNR ADC RoHS:否 制造商:Analog Devices 通道数量: 结构: 转换速率: 分辨率: 输入类型: 信噪比: 接口类型: 工作电源电压: 最大工作温度: 安装风格: 封装 / 箱体: |
| AD9258BCPZRL7-1051 | 制造商:AD 制造商全称:Analog Devices 功能描述:14-Bit, 80 MSPS/105 MSPS/125 MSPS, 1.8 V Dual Analog-to-Digital Converter (ADC) |
发布紧急采购，3分钟左右您将得到回复。