- 您现在的位置：买卖IC网 > PDF目录1986 > AD9287BCPZRL7-100 (Analog Devices Inc)IC ADC 8BIT QUAD 100MSPS 48LFCSP PDF资料下载
参数资料
| 型号： | AD9287BCPZRL7-100 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 30/52页 |
| 文件大小： | 0K |
| 描述： | IC ADC 8BIT QUAD 100MSPS 48LFCSP |
| 产品变化通告： | Product Discontinuation 12/Mar/2010 |
| 标准包装： | 1 |
| 位数： | 8 |
| 采样率（每秒）： | 100M |
| 数据接口： | 串行，SPI? |
| 转换器数目： | 4 |
| 功率耗散（最大）： | 562mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 48-LFCSP-VQ（7x7） |
| 包装： | 标准包装 |
| 输入数目和类型： | 8 个单端，单极；4 个差分，单极 |
| 配用： | AD9287-100EBZ-ND - BOARD EVALUATION AD9287 |
| 其它名称： | AD9287BCPZRL7-100DKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页当前第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
AD9287
Data Sheet
Rev. E | Page 36 of 52
DEFAULT OPERATION AND JUMPER SELECTION
SETTINGS
The following is a list of the default and optional settings or
modes allowed on the AD9287 Rev. A evaluation board.
POWER: Connect the switching power supply that is
provided with the evaluation kit between a rated 100 V ac
to 240 V ac wall outlet at 47 Hz to 63 Hz and P503.
AIN: The evaluation board is set up for a transformer-
coupled analog input with an optimum 50 impedance
match of 190 MHz of bandwidth (see Figure 61). For more
bandwidth response, the differential capacitor across the
analog inputs can be changed or removed. The common
mode of the analog inputs is developed from the center tap
of the transformer or AVDD_DUT/2.
0
A
MPL
IT
U
D
E
(d
B
F
S)
FREQUENCY (MHz)
05966-
088
0
–16
–14
–12
–10
–8
–6
–4
–2
50
100
150
200
250
300
350
400
450
500
–3dB CUTOFF = 190MHz
Figure 61. Evaluation Board Full-Power Bandwidth
VREF: VREF is set to 1.0 V by tying the SENSE pin to ground,
R237. This causes the ADC to operate in 2.0 V p-p full-scale
range. A separate external reference option using the ADR510
is also included on the evaluation board. Populate R231 and
R235 and remove C214. Proper use of the VREF options is
noted in the Voltage Reference section.
RBIAS: RBIAS has a default setting of 10 k (R201) to
ground and is used to set the ADC core bias current.
CLOCK: The default clock input circuitry is derived from a
simple transformer-coupled circuit using a high bandwidth
1:1 impedance ratio transformer (T201) that adds a very
low amount of jitter to the clock path. The clock input is
50 terminated and ac-coupled to handle single-ended
sine wave types of inputs. The transformer converts the
single-ended input to a differential signal that is clipped
before entering the ADC clock inputs.
A differential LVPECL clock can also be used to clock the
ADC input using the AD9515 (U202). Populate R225 and
R227 with 0 resistors and remove R217 and R218 to
disconnect the default clock path inputs. In addition, populate
C207 and C208 with a 0.1 μF capacitor and remove C210 and
C211 to disconnect the default clock path outputs. The
AD9515 has many pin-strappable options that are set to a
default mode of operation. Consult the AD9515 data sheet
for more information about these and other options.
In addition, an on-board oscillator is available on the OSC201
and can act as the primary clock source. The setup is quick
and involves installing R212 with a 0 resistor and setting
the enable jumper (J205) to the on position. If the user wishes
to employ a different oscillator, two oscillator footprint options
are available (OSC201) to check the ADC performance.
PDWN: To enable the power-down feature, short J201 to
AVDD on the PDWN pin.
SCLK/DTP: To enable the digital test patterns on the digital
outputs of the ADC, use J204. If J204 is tied to AVDD during
device power-up, Test Pattern 1000 0000 is enabled. See the
SCLK/DTP Pin section for details.
SDIO/ODM: To enable the low power, reduced signal option
(similar to the IEEE 1595.3 reduced range link LVDS output
standard), use J203. If J203 is tied to AVDD during device
power-up, it enables the LVDS outputs in a low power,
reduced signal option from the default ANSI-644 standard.
This option changes the signal swing from 350 mV p-p to
200 mV p-p, reducing the power of the DRVDD supply. See
the SDIO/ODM Pin section for more details.
CSB: To enable processing of the SPI information on the SDIO
and SCLK pins, tie J202 low in the always enable mode. To
ignore the SDIO and SCLK information, tie J202 to AVDD.
Non-SPI Mode: For users who wish to operate the DUT
without using SPI, remove Jumpers J202, J203, and J204.
This disconnects the CSB, SCLK/DTP, and SDIO/ODM pins
from the control bus, allowing the DUT to operate in its
simplest mode. Each of these pins has internal termination
and will float to its respective level.
D + x, D x: If an alternative data capture method to the setup
shown in Figure 60 is used, optional receiver terminations,
R206 to R211, can be installed next to the high speed back-
plane connector.
相关PDF资料 |
PDF描述 |
|---|---|
| AD9288BSTZ-100 | IC ADC 8BIT DUAL 100MSPS 48-LQFP |
| AD9289BBC | IC ADC 8BIT QUAD 65MSPS 64CSPBGA |
| AD9410BSVZ | IC ADC 10BIT 210MSPS 80-TQFP |
| AD9411BSVZ-170 | IC ADC 10BIT 170MSPS 100TQFP |
| AD9430BSVZ-170 | IC ADC 12BIT 170MSPS 3.3V100TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9288 | 制造商:AD 制造商全称:Analog Devices 功能描述:8-Bit, 40/80/100 MSPS Dual A/D Converter |
| AD9288/PCB | 制造商:Analog Devices 功能描述:8 BIT 40/80/100 MSPS DUAL ADC EVAL BOARD - Bulk |
| AD9288BST-100 | 制造商:Analog Devices 功能描述:ADC Dual Pipelined 100Msps 8-bit Parallel 48-Pin LQFP 制造商:Analog Devices 功能描述:IC 8-BIT ADC |
| AD9288BST-100 | 制造商:Analog Devices 功能描述:A/D CONVERTER (A-D) IC |
| AD9288BST-40 | 制造商:Analog Devices 功能描述:ADC Dual Pipelined 40Msps 8-bit Parallel 48-Pin LQFP 制造商:Analog Devices 功能描述:AD CONVERTOR ((NW)) |
发布紧急采购，3分钟左右您将得到回复。