- 您现在的位置：买卖IC网 > PDF目录16854 > AD9522-0/PCBZ (Analog Devices Inc)BOARD EVAL FOR AD9522-0 CLK GEN PDF资料下载
参数资料
| 型号： | AD9522-0/PCBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 68/84页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL FOR AD9522-0 CLK GEN |
| 设计资源： | AD9522 Eval Board Schematic AD9522 BOM |
| 标准包装： | 1 |
| 主要目的： | 计时，时钟发生器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | AD9522-0 |
| 主要属性： | 12 LVDS/24 CMOS 输出，2.8 GHz VCO |
| 次要属性： | I²C & SPI 接口 |
| 已供物品： | 板 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页当前第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页
AD9522-0
Rev. 0 | Page 70 of 84
Reg.
Addr
(Hex) Bit(s) Name
Description
018
[0]
VCO calibration
now
Bit used to initiate the VCO calibration. This bit must be toggled from 0 to 1 in the active registers. The
sequence to initiate a calibration follows: program to 0, followed by an IO_UPDATE bit (Register 0x232[0]);
then program to 1, followed by another IO_UPDATE bit (Register 0x232[0]). This sequence gives complete
control over when the VCO calibration occurs relative to the programming of other registers that can impact
the calibration (default = 0). Note that the VCO divider (Register 0x1E0[2:0]) must not be static during VCO
calibration.
019
[7:6]
R, A, B counters
SYNC pin reset
[7]
[6]
Action
0
Do nothing on SYNC (default).
0
1
Asynchronous reset.
1
0
Synchronous reset.
1
Do nothing on SYNC.
019
[5:3]
R path delay
R path delay, see Table 2 (default: 0x0).
019
[2:0]
N path delay
N path delay, see Table 2 (default: 0x0).
01A
[7]
Enable STATUS
pin divider
Enables a divide-by-4 on the STATUS pin. This makes it easier to look at low duty-cycle signals out of the
R and N dividers.
[7] = 0; divide-by-4 disabled on the STATUS pin (default).
[7] = 1; divide-by-4 enabled on the STATUS pin.
01A
[6]
Ref freq monitor
threshold
Sets the reference (REF1/REF2) frequency monitor’s detection threshold frequency. This does not affect the VCO
frequency monitor’s detection threshold (see Table 17, REF1, REF2, and VCO frequency status monitor parameter).
[6] = 0; frequency valid if the frequency is above 1.02 MHz (default).
[6] = 1; frequency valid if the frequency is above 6 kHz.
01A
[5:0]
LD pin
control
Selects the signal that is connected to the LD pin.
[5]
[4]
[3]
[2]
[1]
[0]
Level or
Dynamic
Signal
Signal at LD Pin
0
LVL
Digital lock detect (high = lock; low = unlock, default).
0
1
DYN
P-channel, open-drain lock detect (analog lock detect).
0
1
0
DYN
N-channel, open-drain lock detect (analog lock detect).
0
1
HIZ
Tristate (high-Z) LD pin.
0
1
0
CUR
Current source lock detect (110 μA when DLD is true).
0
X
LVL
Ground (dc); for all other cases of 0XXXXX not specified.
The selections that follow are the same as for REFMON.
1
0
LVL
Ground (dc).
1
0
1
DYN
REF1 clock (differential reference when in differential mode).
1
0
1
0
DYN
REF2 clock (N/A in differential mode).
1
0
1
DYN
Selected reference to PLL (differential reference when in
differential mode).
1
0
1
0
DYN
Unselected reference to PLL (not available in differential mode).
1
0
1
0
1
LVL
Status of selected reference (status of differential reference);
active high.
1
0
1
0
LVL
Status of unselected reference (not available in differential
mode); active high.
1
0
1
LVL
Status REF1 frequency (active high).
1
0
1
0
LVL
Status REF2 frequency (active high).
1
0
1
0
1
LVL
(Status REF1 frequency) AND (status REF2 frequency).
1
0
1
0
1
0
LVL
(DLD) AND (status of selected reference) AND (status of VCO).
1
0
1
0
1
LVL
Status of VCO frequency (active high).
1
0
1
0
LVL
Selected reference (low = REF1, high = REF2).
1
0
1
0
1
LVL
DLD; active high.
1
0
1
0
LVL
Holdover active (active high).
1
0
1
LVL
N/A, do not use.
1
0
LVL
VS (PLL supply).
1
0
1
DYN
REF1 clock (differential reference when in differential mode).
相关PDF资料 |
PDF描述 |
|---|---|
| EBM22DCMT-S288 | CONN EDGECARD 44POS .156 EXTEND |
| RNF-100-MINI-SPL-3/64-BK | HEATSHRINK RNF-100 3/64"X100'BLK |
| V110B36E150B3 | CONVERTER MOD DC/DC 36V 150W |
| RNF-100-MINI-SPL-1/16-BK | HEATSHRINK RNF-100 1/16"X75'BLK |
| H4PXS-2036G | DIP CABLE - HDP20S/AE20G/X |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9522-1 | 制造商:AD 制造商全称:Analog Devices 功能描述:12 LVDS/24 CMOS Output Clock Generator with Integrated 2.4 GHz VCO |
| AD9522-1/PCBZ | 功能描述:BOARD EVAL FOR AD9522-1 CLK GEN RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:- 主要目的:电信，线路接口单元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要属性:T1/J1/E1 LIU 次要属性:- 已供物品:板，电源，线缆，CD 其它名称:82EBV2081 |
| AD9522-1BCPZ | 功能描述:IC CLOCK GEN 2.5GHZ VCO 64LFCSP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:- 标准包装:1,000 系列:Precision Edge® 类型:时钟/频率合成器 PLL:无 输入:CML，PECL 输出:CML 电路数:1 比率 - 输入:输出:2:1 差分 - 输入:输出:是/是 频率 - 最大:10.7GHz 除法器/乘法器:无/无 电源电压:2.375 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-VFQFN 裸露焊盘，16-MLF? 供应商设备封装:16-MLF?（3x3） 包装:带卷 (TR) 其它名称:SY58052UMGTRSY58052UMGTR-ND |
| AD9522-1BCPZ-REEL7 | 功能描述:IC CLOCK GEN 2.5GHZ VCO 64LFCSP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 时钟发生器，PLL，频率合成器 系列:- 标准包装:2,000 系列:- 类型:PLL 时钟发生器 PLL:带旁路 输入:LVCMOS，LVPECL 输出:LVCMOS 电路数:1 比率 - 输入:输出:2:11 差分 - 输入:输出:是/无 频率 - 最大:240MHz 除法器/乘法器:是/无 电源电压:3.135 V ~ 3.465 V 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:32-LQFP 供应商设备封装:32-TQFP（7x7） 包装:带卷 (TR) |
| AD9522-2 | 制造商:AD 制造商全称:Analog Devices 功能描述:12 LVDS/24 CMOS Output Clock Generator with Integrated 2.2 GHz VCO |
发布紧急采购，3分钟左右您将得到回复。