收藏本站
参数资料
型号： ADE5166ASTZF62
厂商： Analog Devices Inc
文件页数： 31/156页
文件大小： 0K
描述： IC METER/8052/RTC/LCD DRV 64LQFP
产品变化通告： Product Discontinuance 27/Oct/2011
标准包装： 1
输入阻抗： *
测量误差： *
电压 - 高输入/输出： *
电压 - 低输入/输出： *
电流 - 电源： *
电源电压： *
测量仪表类型： *
工作温度： *
安装类型： 表面贴装
封装/外壳： 64-LQFP
供应商设备封装： 64-LQFP（10x10）
包装： 托盘
Data Sheet
POWER SUPPLY ARCHITECTURE
The ADE5166/ADE5169/ADE5566/ADE5569 have two power
supply inputs, V DD and V BAT . They require only a single 3.3 V power
supply at V DD for full operation. A battery backup, or secondary
power supply, with a maximum of 3.7 V can be connected to the
V BAT input. Internally, the ADE5166/ADE5169/ADE5566/
ADE5569 connect V DD or V BAT to V SWOUT , which is used to derive
power for the ADE5166/ADE5169/ADE5566/ADE5569 circuitry.
The V SWOUT output pin reflects the voltage at the internal power
supply (V SWOUT ) and has a maximum output current of 6 mA. This
pin can also be used to power a limited number of peripheral com-
ponents. The 2.5 V analog supply (V INTA ) and the 2.5 V supply for
the core logic (V INTD ) are derived by on-chip linear regulators from
V SWOUT . Figure 32 shows the ADE5166/ADE5169/ADE5566/
ADE5569 power supply architecture.
V DCIN V DD V BAT V SWOUT
ADE5166/ADE5169/ADE5566/ADE5569
stable power supply to the ADE5166/ADE5169/ADE5566/
ADE5569, as long as the external battery voltage is above 2.75 V.
It allows continuous code execution even while the internal power
supply is switching from V DD to V BAT and back. Note that the energy
metering ADCs are not available when V BAT is used for V SWOUT .
Power supply management (PSM) interrupts can be enabled to
indicate when battery switchover occurs and when the V DD power
supply is restored (see the Power Supply Management (PSM)
Interrupt section).
Switching from V DD to V BAT
The following three events switch the internal power supply
(V SWOUT ) from V DD to V BAT :
? V DCIN < 1.2 V. When V DCIN falls below 1.2 V, V SWOUT switches
from V DD to V BAT . This event is enabled when the BATPRG
bits (Bits[1:0]) in the battery switchover configuration SFR
(BATPR, Address 0xF5) are set to 0b01.
ADC
LDO
V INTD
MCU
?
V DD < 2.75 V. When V DD falls below 2.75 V, V SWOUT switches
from V DD to V BAT . This event is enabled when the BATPRG
BCTRL
POWER SUPPLY
MANAGEMENT
V SW
LDO
V INTA
ADE
?
bits in the BATPR SFR are cleared.
Falling edge on BCTRL. When the battery control pin,
ADC
SPI/I 2 C
BCTRL, goes low, V SWOUT switches from V DD to V BAT . This
external switchover signal can trigger a switchover to V BAT
SCRATCH PAD LCD
TEMPERATURE ADC
RTC
3.3V
UART
2.5V
at any time. Setting the INT1PRG bits (Bits[3:1]) to 0bX01 in
the interrupt pins configuration SFR (INTPR, Address 0xFF)
enables the BCTRL pin (see Table 17).
Figure 32. Power Supply Architecture
The ADE5166/ADE5169/ADE5566/ADE5569 provide automatic
battery switchover between V DD and V BAT based on the voltage
level detected at V DD or V DCIN . In addition, the BCTRL input can be
used to trigger a battery switchover. The conditions for switching
V SWOUT from V DD to V BAT and back to V DD are described in the
Battery Switchover section. V DCIN is an input pin that can be con-
nected to a dc signal of 0 V to 3.3 V. This input is intended for
power supply supervisory purposes and does not provide power
to the ADE5166/ADE5169/ADE5566/ADE5569 circuitry (see
the Battery Switchover section).
BATTERY SWITCHOVER
The ADE5166/ADE5169/ADE5566/ADE5569 monitor V DD ,
V BAT , and V DCIN . Automatic battery switchover from V DD to V BAT
can be configured based on the status of the V DD , V DCIN , or BCTRL
pin. Battery switchover is enabled by default. Setting Bit 1 in the
battery switchover configuration SFR (BATPR, Address 0xF5)
disables battery switchover so that V DD is always connected to
V SWOUT (see Table 19). The source of V SWOUT is indicated by Bit 6
in the peripheral configuration SFR (PERIPH, Address 0xF4),
which is described in Table 20. Bit 6 is set when V SWOUT is con-
nected to V DD and cleared when V SWOUT is connected to V BAT .
The battery switchover functionality provided by the ADE5166/
ADE5169/ADE5566/ADE5569 allows a seamless transition from
V DD to V BAT . An automatic battery switchover option ensures a
Switching from V BAT to V DD
To switch V SWOUT from V BAT to V DD , all of the following events
must be true:
? V DD > 2.75 V. V SWOUT switches back to V DD after V DD remains
above 2.75 V.
? V DCIN > 1.2 V and V DD > 2.75 V. If the low V DCIN condition
is enabled, V SWOUT switches to V DD after V DCIN remains
above 1.2 V and V DD remains above 2.75 V.
? Rising edge on BCTRL. If the battery control pin is enabled,
V SWOUT switches back to V DD after BCTRL is high, and the
first or second bullet point is satisfied.
POWER SUPPLY MANAGEMENT (PSM) INTERRUPT
The power supply management (PSM) interrupt alerts the 8052
core of power supply events. The PSM interrupt is disabled by
default. Setting Bit 1 (EPSM) in the Interrupt Enable and Priority 2
SFR (IEIP2, Address 0xA9) enables the PSM interrupt (see
Table 83).
The power management interrupt enable SFR (IPSME,
Address 0xEC) controls the events that result in a PSM interrupt
(see Table 21).
Figure 33 illustrates how the PSM interrupt vector is shared among
the PSM interrupt sources. The PSM interrupt flags are latched
and must be cleared by writing to the power management interrupt
flag SFR (IPSMF, Address 0xF8), as described in Table 18.
Rev. D | Page 31 of 156
相关PDF资料
PDF描述
NCP699SN28T1G IC REG LDO 2.8V 240MA 5TSOP
RSC50DRYN-S13 CONN EDGECARD 100POS .100 EXTEND
LFEC3E-4QN208I IC FPGA 3.1KLUTS 208PQFP
KSZ8995MAI IC SWITCH 5-PORT 10/100 128PQFP
MIC5281-3.3YMME TR IC REG LDO 3.3V 25MA 8MSOP-EP
相关代理商/技术参数
参数描述
ADE5166ASTZF62-RL 功能描述:IC METER/8052/RTC/LCD DRV 64LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:*
ADE5169 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC, and LCD Driver
ADE5169ASTZF62 功能描述:IC METER/8052/RTC/LCD DR 64LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:*
ADE5169ASTZF62-RL 功能描述:IC METER/8052/RTC/LCD DRV 64LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:*
ADE5566 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC, and LCD Driver
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*