- 您现在的位置：买卖IC网 > PDF目录4596 > ADE7518ASTZF16 (Analog Devices Inc)IC ENERGY METER MCU 16K 64LQFP PDF资料下载
参数资料
| 型号： | ADE7518ASTZF16 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 104/128页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METER MCU 16K 64LQFP |
| 产品变化通告： | Product Discontinuance 27/Oct/2011 |
| 特色产品： | ADE7518: Single-phase Energy-Measurement IC |
| 标准包装： | 160 |
| 输入阻抗： | * |
| 测量误差： | * |
| 电压 - 高输入/输出： | * |
| 电压 - 低输入/输出： | * |
| 电流 - 电源： | * |
| 电源电压： | * |
| 测量仪表类型： | * |
| 工作温度： | * |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-LQFP（10x10） |
| 包装： | 托盘 |
| 产品目录页面： | 797 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页当前第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页
ADE7518
Take care when changing the interval timer time base. The
recommended procedure is as follows:
with FSEL[1:0] = 00 and 512 Hz with FSEL[1:0] = 01 in the
Interrupt Pins Configuration SFR (INTPR, 0xFF).
1.
2.
3.
If the Alarm Interval SFR (INTVAL, 0xA6) is going to
be modified, write to this register first. Then, wait for
one 128 Hz clock cycle to synchronize with the RTC,
64,000 cycles at a 4.096 MHz instruction cycle clock.
Disable the interval timer by clearing the ITEN bit in the
RTC Configuration SFR (TIMECON, 0xA1). Then, wait
for one 128 Hz clock cycle to synchronize with the RTC,
64,000 cycles at a 4.096 MHz instruction cycle clock.
Read the TIMECON SFR to ensure that the ITEN bit is
A shorter window of 0.244 sec is offered for fast calibration
during PSM0 or PSM1. Two output frequencies are offered for
this RTC calibration output mode: 500 Hz with FSEL[1:0] = 10
and 16.384 kHz with FSEL[1:0] = 11 in the INTPR SFR. Note
that for the 0.244 sec calibration window, the RTC is clocked
125 times faster than in normal mode, resulting in timekeeping
registers that represent seconds/125, minutes/125, and hours/125
instead of seconds, minutes, and hours. Therefore, this mode
should be used for calibration only.
4.
clear. If it is not, wait for another 128 Hz clock cycle.
Set the time base bits (ITS[1:0]) in the TIMECON SFR to
configure the interval. Wait for a 128 Hz clock cycle for this
change to take effect.
Table 119. RTC Calibration Options
Calibration
Option FSEL[1:0] Window (Sec)
Normal Mode 0 00 30.5
f RTCCAL (Hz)
1
The RTC alarm event wakes the 8052 MCU core if the MCU is
in PSM2 when the alarm event occurs.
RTC CALIBRATION
Normal Mode 1
Calibration Mode 0
Calibration Mode 1
01
10
11
30.5
0.244
0.244
512
500
16,384
The RTC provides registers to calibrate the nominal external
crystal frequency and its variation over temperature. A frequency
error up to ±248 ppm can be calibrated by the RTC circuitry,
which adds or subtracts pulses from the external crystal signal.
The nominal crystal frequency should be calibrated with the
RTC nominal compensation register so that the clock going into
the RTC is precisely 32.768 kHz at 25°C. The RTC Temperature
Compensation SFR (TEMPCAL, 0xF7) is used to compensate
for the external crystal drift over temperature by adding or
subtracting additional pulses based on temperature.
The LSB of each RTC compensation register represents a
±2 ppm frequency error. The RTC compensation circuitry adds
the RTC Temperature Compensation SFR (TEMPCAL, 0xF7)
and the RTC Nominal Compensation SFR (RTCCOMP, 0xF6)
to determine how much compensation is required. Note that
When no RTC compensation is applied, that is, when RTC
Nominal Compensation SFR (RTCCOMP, 0xF6) and RTC
Temperature Compensation SFR (TEMPCAL, 0xF7) are equal
to 0, the nominal compensation required to account for the
error in the external crystal can be determined. In this case, it is
not necessary to wait for an entire calibration window to determine
the error in the pulse output. Calculating the error in frequency
between two consecutive pulses on the P0.2/CF1/RTCCAL pin
is sufficient.
The value to write to the RTC Nominal Compensation SFR
(RTCCOMP, 0xF6) is calculated from the % error or seconds per
day error on the frequency output. Each LSB of the RTCCOMP
SFR represents 2 ppm of correction where 1 sec/day error is
equal to 11.57 ppm.
RTCCOMP = 5000 × (% Error )
the sum of these two registers is limited to ±248 ppm.
Calibration Flow
RTCCOMP =
1
2 × 11 . 57
× ( sec/day Error )
An RTC calibration pulse output is provided on the P0.2/CF1/
RTCCAL pin. Enable the RTC output by setting the RTCCAL
bit in the Interrupt Pins Configuration SFR (INTPR, 0xFF).
The RTC calibration is accurate to within ±2 ppm over a 30.5 sec
During calibration, user software writes the RTC with the
current time. Refer to the Read and Write Operations section
for more information on how to read and write the RTC
timekeeping registers.
window in all operational modes: PSM0, PSM1, and PSM2. Two
output frequencies are offered for the normal RTC mode: 1 Hz
Rev. 0 | Page 104 of 128
相关PDF资料 |
PDF描述 |
|---|---|
| ADE7156ASTZF8 | IC ENERGY METER 64-LQFP |
| ADE7156ASTZF16-RL | IC ENERGY METER 64-LQFP |
| ADE7116ASTZF8-RL | IC ENERGY METER 64-LQFP |
| ADE7116ASTZF8 | IC ENERGY METER 64-LQFP |
| ADE5166ASTZF62-RL | IC METER/8052/RTC/LCD DRV 64LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADE7518ASTZF16-RL | 功能描述:IC ENERGY METER MCU 16K 64LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7518ASTZF8 | 功能描述:IC ENERGY METER MCU 8K 64LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7518ASTZF8-RL | 功能描述:IC ENERGY METER MCU 8K 64LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7566 | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC, and LCD Driver |
| ADE7566ACPZF16 | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC, and LCD Driver |
发布紧急采购，3分钟左右您将得到回复。