- 您现在的位置：买卖IC网 > PDF目录4596 > ADE7518ASTZF16 (Analog Devices Inc)IC ENERGY METER MCU 16K 64LQFP PDF资料下载
参数资料
| 型号： | ADE7518ASTZF16 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 79/128页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METER MCU 16K 64LQFP |
| 产品变化通告： | Product Discontinuance 27/Oct/2011 |
| 特色产品： | ADE7518: Single-phase Energy-Measurement IC |
| 标准包装： | 160 |
| 输入阻抗： | * |
| 测量误差： | * |
| 电压 - 高输入/输出： | * |
| 电压 - 低输入/输出： | * |
| 电流 - 电源： | * |
| 电源电压： | * |
| 测量仪表类型： | * |
| 工作温度： | * |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-LQFP（10x10） |
| 包装： | 托盘 |
| 产品目录页面： | 797 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页当前第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页
ADE7518
WATCHDOG TIMER
The watchdog timer generates a device reset or interrupt within
a reasonable amount of time if the ADE7518 enters an erroneous
state, possibly due to a programming error or electrical noise. The
watchdog is enabled by default with a timeout of two seconds and
creates a system reset if not cleared within two seconds. The
watchdog function can be disabled by clearing the watchdog
enable bit (WDE) in the Watchdog Timer SFR (WDCON, 0xC0).
The watchdog circuit generates a system reset or interrupt (WDS)
if the user program fails to set the WDE bit within a predeter-
mined amount of time (set by PRE[3:0]). The watchdog timer is
clocked from the 32.768 kHz external crystal connected between
the XTAL1 and XTAL2 pins.
The WDCON SFR can be written only by user software if the
double write sequence described in the Writing to the Watchdog
Timer SFR (WDCON, 0xC0) section is initiated on every write
access to the WDCON SFR.
To prevent any code from inadvertently disabling the watchdog,
a watchdog protection can be activated. This watchdog protection
locks in the watchdog enable and event settings so that they cannot
be changed by user code. The protection is activated by clearing
a watchdog protection bit in the flash memory. The watchdog
protection bit is the most significant bit at Address 0x3FFA of
the flash memory. When this bit is cleared, the WDIR bit is forced
to 0, and the WDE bit is forced to 1. Note that the sequence for
configuring the flash protection bits must be followed to modify
the watchdog protection bit at Address 0x3FFA (see the Protecting
the Flash Memory section).
Table 65. Watchdog Timer SFR (WDCON, 0xC0)
Bit
7 to 4
Address
0xC7 to
Mnemonic
PRE[3:0]
Default
7
Description
Watchdog Prescaler. In normal mode, the 16-bit watchdog timer is clocked by the input
0xC4
clock (32.768 kHz). The PREx bits set which of the upper bits of the counter are used as the
watchdog output, as follows:
t WATCHDOG = 2 PRE ×
2 9
XTAL 1
PRE[3:0] Result (Watchdog Timeout)
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010 to 1111
15.6 ms
31.2 ms
62.5 ms
125 ms
250 ms
500 ms
1 sec
2 sec
0 sec, automatic reset
0 sec, serial download reset
Not a valid selection
3
0xC3
WDIR
0
Watchdog Interrupt Response Bit. When cleared, the watchdog generates a system reset
when the watchdog timeout period has expired. When set, the watchdog generates an
interrupt when the watchdog timeout period has expired.
2
0xC2
WDS
0
Watchdog Status Bit. This bit is set to indicate that a watchdog timeout has occurred. It is
cleared by writing a 0 or by an external hardware reset. A watchdog reset does not clear
WDS; therefore, it can be used to distinguish between a watchdog reset and a hardware
reset from the RESET pin.
1
0xC1
WDE
1
Watchdog Enable Bit. When set, this bit enables the watchdog and clears its counter. The
watchdog counter is subsequently cleared again whenever WDE is set. If the watchdog is
not cleared within its selected timeout period, it generates a system reset or watchdog
interrupt, depending on the WDIR bit.
0
0xC0
WDWR
0
Watchdog Write Enable Bit. See the Writing to the Watchdog Timer SFR (WDCON, 0xC0)
section.
Rev. 0 | Page 79 of 128
相关PDF资料 |
PDF描述 |
|---|---|
| ADE7156ASTZF8 | IC ENERGY METER 64-LQFP |
| ADE7156ASTZF16-RL | IC ENERGY METER 64-LQFP |
| ADE7116ASTZF8-RL | IC ENERGY METER 64-LQFP |
| ADE7116ASTZF8 | IC ENERGY METER 64-LQFP |
| ADE5166ASTZF62-RL | IC METER/8052/RTC/LCD DRV 64LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADE7518ASTZF16-RL | 功能描述:IC ENERGY METER MCU 16K 64LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7518ASTZF8 | 功能描述:IC ENERGY METER MCU 8K 64LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7518ASTZF8-RL | 功能描述:IC ENERGY METER MCU 8K 64LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7566 | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC, and LCD Driver |
| ADE7566ACPZF16 | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC, and LCD Driver |
发布紧急采购，3分钟左右您将得到回复。