- 您现在的位置：买卖IC网 > PDF目录4596 > ADE7518ASTZF16 (Analog Devices Inc)IC ENERGY METER MCU 16K 64LQFP PDF资料下载
参数资料
| 型号： | ADE7518ASTZF16 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 54/128页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METER MCU 16K 64LQFP |
| 产品变化通告： | Product Discontinuance 27/Oct/2011 |
| 特色产品： | ADE7518: Single-phase Energy-Measurement IC |
| 标准包装： | 160 |
| 输入阻抗： | * |
| 测量误差： | * |
| 电压 - 高输入/输出： | * |
| 电压 - 低输入/输出： | * |
| 电流 - 电源： | * |
| 电源电压： | * |
| 测量仪表类型： | * |
| 工作温度： | * |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-LQFP（10x10） |
| 包装： | 托盘 |
| 产品目录页面： | 797 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页当前第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页
ADE7518
? Reactive Power × ? 1 +
? ?
?
? ?
2 12
Reactive Power Gain Calibration
Figure 58 shows the signal processing chain for the ADE7518
reactive power calculation. As explained in the Reactive Power
Calculation section, the reactive power is calculated by applying a
low-pass filter to the instantaneous reactive power signal. Note
that, when reading the waveform samples from the output of
LPF2, the gain of the reactive energy can be adjusted by using
the multiplier and by writing a twos complement, 12-bit word
to the VAR gain register (VARGAIN[11:0]). Equation 23 shows
how the gain adjustment is related to the contents of the watt
gain register.
Output VARGAIN =
? ? VARGAIN ? ?
(23)
?
The resolution of the VARGAIN register is the same as the
WGAIN register (see the Active Power Gain Calibration
section). VARGAIN can be used to calibrate the reactive
power (or energy) calculation in the ADE7518.
Reactive Power Offset Calibration
The ADE7518 also incorporates a reactive power offset register
(VAROS[15:0]). This is a signed, twos complement, 16-bit register
that can be used to remove offsets in the reactive power calculation
(see Figure 58). An offset may exist in the reactive power calcula-
tion due to crosstalk between channels on the PCB or in the IC
itself. The offset calibration allows the contents of the reactive
power register to be maintained at 0 when no power is being
consumed.
The 256 LSBs (VAROS = 0x100) written to the reactive power
offset register are equivalent to 1 LSB in the WAVMODE register.
Sign of Reactive Power Calculation
Note that the average reactive power is a signed calculation.
The phase-shift filter has ?90° phase shift when the integrator
is enabled, and +90° phase shift when the integrator is disabled.
Table 43 summarizes how the relationship of the phase difference
between the voltage and the current affects the sign of the resulting
VAR calculation.
Table 43. Sign of Reactive Power Calculation
interrupt stays active until the VARSIGN status bit is cleared
(see the Energy Measurement Interrupts section).
When VARSIGN in the ACCMODE register (0x0F) is cleared
(default), the VARSIGN flag in the Interrupt Status 1 SFR
(MIRQSTL, 0xDC) is set when a transition from positive to
negative reactive power occurs.
If VARSIGN in the ACCMODE register (0x0F) is set, the
VARSIGN flag in the Interrupt Status 1 SFR (MIRQSTL,
0xDC) is set when a transition from negative to positive
reactive power occurs.
Reactive Power No Load Detection
The ADE7518 includes a no load threshold feature on the reactive
energy that eliminates any creep effects in the meter. The ADE7518
accomplishes this by not accumulating reactive energy when
the multiplier output is below the no load threshold. When the
reactive power is below the no load threshold, the RNOLOAD
flag in the Interrupt Status 1 SFR (MIRQSTL, 0xDC) is set. If the
RNOLOAD bit is set in the Interrupt Enable 1 SFR (MIRQENL,
0xD9), the 8052 core has a pending ADE interrupt. The ADE
interrupt stays active until the RNOLOAD status bit is cleared
(see the Energy Measurement Interrupts section).
The no load threshold level is selectable by setting the
VARNOLOAD bits in the NLMODE register (0x0E). Setting
these bits to 0b00 disables the no load detection, and setting
them to 0b01, 0b10, or 0b11 sets the no load detection threshold
to 0.015%, 0.0075%, and 0.0037% of the full-scale output
frequency of the multiplier, respectively.
REACTIVE ENERGY CALCULATION
As for reactive energy, the ADE7518 achieves the integration of
the reactive power signal by continuously accumulating the
reactive power signal in an internal, nonreadable, 49-bit energy
register. The reactive energy register (VARHR[23:0]) represents
the upper 24 bits of this internal register.
The discrete time sample period (T) for the accumulation register
in the ADE7518 is 1.22 μs (5/MCLK). As well as calculating the
energy, this integration removes any sinusoidal components
that may be in the active power signal. Figure 58 shows this
discrete time integration or accumulation. The reactive power
Angle
Between 0 ° to +90 °
Between –90 ° to 0 °
Between 0 ° to +90 °
Between –90 ° to 0 °
Integrator
Off
Off
On
On
Sign
Positive
Negative
Positive
Negative
signal in the waveform register is continuously added to the
internal reactive energy register.
The reactive energy accumulation depends on the setting of the
SAVARM and ABSVARM bits in the ACCMODE register (0x0F).
When both bits are cleared, the addition is signed and, therefore,
Reactive Power Sign Detection
The ADE7518 detects a change of sign in the reactive power.
The VARSIGN flag in the Interrupt Status 1 SFR (MIRQSTL,
negative energy is subtracted from the reactive energy contents.
When both bits are set, the ADE7518 is set to be in the more
restrictive mode, the absolute accumulation mode.
0xDC) records when a change of sign has occurred according
to the VARSIGN bit in the ACCMODE register (0x0F). If the
VARSIGN bit is set in the Interrupt Enable 1 SFR (MIRQENL,
0xD9), the 8052 core has a pending ADE interrupt. The ADE
Rev. 0 | Page 54 of 128
相关PDF资料 |
PDF描述 |
|---|---|
| ADE7156ASTZF8 | IC ENERGY METER 64-LQFP |
| ADE7156ASTZF16-RL | IC ENERGY METER 64-LQFP |
| ADE7116ASTZF8-RL | IC ENERGY METER 64-LQFP |
| ADE7116ASTZF8 | IC ENERGY METER 64-LQFP |
| ADE5166ASTZF62-RL | IC METER/8052/RTC/LCD DRV 64LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADE7518ASTZF16-RL | 功能描述:IC ENERGY METER MCU 16K 64LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7518ASTZF8 | 功能描述:IC ENERGY METER MCU 8K 64LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7518ASTZF8-RL | 功能描述:IC ENERGY METER MCU 8K 64LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7566 | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC, and LCD Driver |
| ADE7566ACPZF16 | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC, and LCD Driver |
发布紧急采购，3分钟左右您将得到回复。