- 您现在的位置：买卖IC网 > PDF目录4596 > ADE7518ASTZF16 (Analog Devices Inc)IC ENERGY METER MCU 16K 64LQFP PDF资料下载
参数资料
| 型号： | ADE7518ASTZF16 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 45/128页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METER MCU 16K 64LQFP |
| 产品变化通告： | Product Discontinuance 27/Oct/2011 |
| 特色产品： | ADE7518: Single-phase Energy-Measurement IC |
| 标准包装： | 160 |
| 输入阻抗： | * |
| 测量误差： | * |
| 电压 - 高输入/输出： | * |
| 电压 - 低输入/输出： | * |
| 电流 - 电源： | * |
| 电源电压： | * |
| 测量仪表类型： | * |
| 工作温度： | * |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-LQFP（10x10） |
| 包装： | 托盘 |
| 产品目录页面： | 797 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页当前第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页
ADE7518
Line Voltage SAG Detection
In addition to detection of the loss of the line voltage signal
(zero crossing), the ADE7518 can also be programmed to detect
when the absolute value of the line voltage drops below a certain
peak value for a number of line cycles. This condition is illu-
V 2
VPKLVL[15:0]
strated in Figure 44.
FULL SCALE
SAGLVL[15:0]
VOLTAGE CHANNEL
PKV INTERRUPT
FLAG
RESET BIT PKV
IN MIRQSTH SFR
PKV RESET
LOW WHEN
MIRQSTH SFR
IS READ
SAG FLAG
SAGCYC[7:0] = 0x04
3 LINE CYCLES
SAG RESET LOW
WHEN VOLTAGE
CHANNEL EXCEEDS
SAGLVL[15:0] AND
SAG FLAG RESET
Figure 45. Peak Level Detection
Figure 45 shows a line voltage exceeding a threshold that is set in
the voltage peak register (VPKLVL[15:0]). The voltage peak event
is recorded by setting the PKV flag in the Interrupt Status 3 SFR
Figure 44. SAG Detection
Figure 44 shows the line voltage falling below a threshold that
is set in the SAG level register (SAGLVL[15:0]) for three line
cycles. The quantities 0 and 1 are not valid for the SAGCYC
register, and the contents represent one more than the desired
number of full line cycles. For example, when the SAG cycle
(SAGCYC[7:0]) contains 0x04, FSAG in the Power Management
Interrupt Flag SFR (IPSMF, 0xF8) is set at the end of the third
line cycle after the line voltage falls below the threshold. If the SAG
enable bit (ESAG) in the Power Management Interrupt Enable SFR
(IPSME, 0xEC) is set, the 8052 core has a pending power supply
management interrupt. The PSM interrupt stays active until the
ESAG bit is cleared (see the Power Supply Management (PSM)
Interrupt section).
In Figure 44, the SAG flag (FSAG) is set on the fifth line cycle
after the signal on the voltage channel first drops below the
threshold level.
SAG Level Set
The 2-byte contents of the SAG level register (SAGLVL, 0x14)
are compared to the absolute value of the output from LPF1.
Therefore, when LPF1 is enabled, writing 0x2038 to the SAG
level register puts the SAG detection level at full scale (see
Figure 44). Writing 0x00 or 0x01 puts the SAG detection level
at 0. The SAG level register is compared to the input of the ZX
detection, and detection is made when the contents of the SAG
level register are greater.
Peak Detection
The ADE7518 can also be programmed to detect when the
absolute value of the voltage or current channel exceeds a
specified peak value. Figure 45 illustrates the behavior of the
peak detection for the voltage channel. Both voltage and current
channels are monitored at the same time.
(MIRQSTH, 0xDE). If the PKV enable bit is set in the Interrupt
Enable 3 SFR (MIRQENH, 0xDB), the 8052 core has a pending
ADE interrupt. Similarly, the current peak event is recorded by
setting the PKI flag in Interrupt Status 3 SFR (MIRQSTH, 0xDE).
The ADE interrupt stays active until the PKV or PKI status bit
is cleared (see the Energy Measurement Interrupts section).
Peak Level Set
The contents of the VPKLVL and IPKLVL registers are compared
to the absolute value of the voltage and the 2 MSBs of the current
channel, respectively. Thus, for example, the nominal maximum
code from the current channel ADC with a full-scale signal is
0x28F5C2 (see the Current Channel ADC section). Therefore,
writing 0x28F5 to the IPKLVL register puts the peak detection
level of the current channel at full scale and sets the current
peak detection to its least sensitive value. Writing 0x00 puts the
current channel detection level at 0. The detection is done by
comparing the contents of the IPKLVL register to the incoming
current channel sample. The PKI flag indicates that the peak
level is exceeded. If the PKI or PKV bit is set in the Interrupt
Enable 3 SFR (MIRQENH, 0xDB), the 8052 core has a pending
ADE interrupt.
Peak Level Record
Each ADE7518 records the maximum absolute value reached by
the voltage and current channels in two different registers,
IPEAK and VPEAK, respectively. Each register is a 24-bit
unsigned register that is updated each time the absolute value of
the waveform sample from the corresponding channel is above
the value stored in the VPEAK or IPEAK register. The contents
of the VPEAK register correspond to the maximum absolute
value observed on the voltage channel input. The contents of
IPEAK and VPEAK represent the maximum absolute value
observed on the current and voltage input, respectively. Reading
the RSTVPEAK and RSTIPEAK registers clears their respective
contents after the read operation.
Rev. 0 | Page 45 of 128
相关PDF资料 |
PDF描述 |
|---|---|
| ADE7156ASTZF8 | IC ENERGY METER 64-LQFP |
| ADE7156ASTZF16-RL | IC ENERGY METER 64-LQFP |
| ADE7116ASTZF8-RL | IC ENERGY METER 64-LQFP |
| ADE7116ASTZF8 | IC ENERGY METER 64-LQFP |
| ADE5166ASTZF62-RL | IC METER/8052/RTC/LCD DRV 64LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADE7518ASTZF16-RL | 功能描述:IC ENERGY METER MCU 16K 64LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7518ASTZF8 | 功能描述:IC ENERGY METER MCU 8K 64LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7518ASTZF8-RL | 功能描述:IC ENERGY METER MCU 8K 64LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7566 | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC, and LCD Driver |
| ADE7566ACPZF16 | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC, and LCD Driver |
发布紧急采购，3分钟左右您将得到回复。