参数资料
型号: ADE7518ASTZF16
厂商: Analog Devices Inc
文件页数: 66/128页
文件大小: 0K
描述: IC ENERGY METER MCU 16K 64LQFP
产品变化通告: Product Discontinuance 27/Oct/2011
特色产品: ADE7518: Single-phase Energy-Measurement IC
标准包装: 160
输入阻抗: *
测量误差: *
电压 - 高输入/输出: *
电压 - 低输入/输出: *
电流 - 电源: *
电源电压: *
测量仪表类型: *
工作温度: *
安装类型: 表面贴装
封装/外壳: 64-LQFP
供应商设备封装: 64-LQFP(10x10)
包装: 托盘
产品目录页面: 797 (CN2011-ZH PDF)
ADE7518
STANDARD 8052 SFRS
The standard 8052 special function registers include the ACC,
B, PSW, DPTR, and SP SFRs described in the Basic 8052 Registers
section. The standard 8052 SFRs also define the timers, the
serial port interface, the interrupts, the I/O ports, and the
power-down modes.
Timer SFRs
The 8052 contains three 16-bit timers: the identical Timer0 and
Timer1, as well as a Timer2. These timers can also function as
event counters. Timer2 has a capture feature where the value of
Program Control Register (PCON, 0x87)
The 8052 core defines two power-down modes: power-down
and idle. The ADE7518 enhances the power control capability
of the traditional 8052 MCU with additional power management
functions. The Power Control SFR (POWCON, 0xC5) is used
to define power control-specific functionality for the ADE7518.
The Program Control SFR (PCON, 0x87) is not bit addressable
(see the Power Management section).
The ADE7518 has many other peripherals not standard to the
8052 core, including
the timer can be captured in two 8-bit registers upon the asser-
tion of an external input signal (see Table 91 and the Timers
section).
Serial Port SFRs
The full-duplex serial port peripheral requires two registers:
one for setting up the baud rate and other communication
parameters, and another for the transmit/receive buffer. The
?
?
?
?
?
?
?
ADE energy measurement DSP
RTC
LCD driver
Battery switchover/power management
SPI/I 2 C communication
Flash memory controller
Watchdog timer
ADE7518 also has enhanced serial port functionality with a
dedicated timer for baud rate generation with a fractional
divisor and additional error detection. See Table 120 and the
MEMORY OVERVIEW
The ADE7518 contains the following memory blocks:
UART Serial Interface section.
Interrupt SFRs
There is a two-tiered interrupt system standard in the 8052 core.
?
?
?
16 kB of on-chip Flash/EE program and data memory
256 bytes of general-purpose RAM
256 bytes of internal extended RAM (XRAM)
The priority level for each interrupt source is individually selecta-
ble as high or low. The ADE7518 enhances this interrupt system
by creating, in essence, a third interrupt tier for the highest
priority, the power supply management (PSM) interrupt (see
the Interrupt System section).
I/O Port SFRs
The 8052 core supports four I/O ports, Port 0 through Port 3,
The 256 bytes of general-purpose RAM share the upper 128 bytes
of its address space with special function registers. All of the
memory spaces are shown in Figure 69. The addressing mode
specifies which memory space to access.
General-Purpose RAM
General-purpose RAM resides in the 0x00 through 0xFF
memory locations and contains the register banks.
where Port 0 and Port 2 are typically used to access external
code and data spaces. The ADE7518, unlike standard 8052
products, provides internal nonvolatile flash memory so that an
external code space is unnecessary. The on-chip LCD driver
requires many pins, some of which are dedicated for LCD
0x30
0x7F
0x2F
GENERAL-PURPOSE
AREA
functionality, and others that can be configured as LCD or
general-purpose inputs/outputs. Due to the limited number of
I/O pins, the ADE7518 does not allow access to external code
and data spaces.
BANKS
SELECTED
VIA
BITS IN PSW
11
0x20
0x18
0x1F
BIT-ADDRESSABLE
(BIT ADDRESSES)
The ADE7518 provides 20 pins that can be used for general-
0x17
purpose I/O. These pins are mapped to Port 0, Port 1, and Port 2.
They are accessed through three bit-addressable 8052 SFRs, P0,
10
0x10
0x0F
FOUR BANKS OF EIGHT
REGISTERS R0 TO R7
STACK POINTER
P1, and P2. Another enhanced feature of the ADE7518 is that
the weak pull-ups that are standard on 8052 Port 1, Port 2, and
Port 3 can be disabled to make open-drain outputs, as is standard
on Port 0. The weak pull-ups can be enabled on a pin-by-pin
basis (see the I/O Ports section).
01
0x08
RESET VALUE OF
0x07
00
0x00
Figure 69. Lower 128 Bytes of Internal Data Memory
Address 0x80 through Address 0xFF of general-purpose RAM
are shared with the special function registers. The mode of
addressing determines which memory space is accessed, as
shown in Figure 70.
Rev. 0 | Page 66 of 128
相关PDF资料
PDF描述
ADE7156ASTZF8 IC ENERGY METER 64-LQFP
ADE7156ASTZF16-RL IC ENERGY METER 64-LQFP
ADE7116ASTZF8-RL IC ENERGY METER 64-LQFP
ADE7116ASTZF8 IC ENERGY METER 64-LQFP
ADE5166ASTZF62-RL IC METER/8052/RTC/LCD DRV 64LQFP
相关代理商/技术参数
参数描述
ADE7518ASTZF16-RL 功能描述:IC ENERGY METER MCU 16K 64LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:*
ADE7518ASTZF8 功能描述:IC ENERGY METER MCU 8K 64LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:*
ADE7518ASTZF8-RL 功能描述:IC ENERGY METER MCU 8K 64LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:*
ADE7566 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC, and LCD Driver
ADE7566ACPZF16 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC, and LCD Driver