- 您现在的位置：买卖IC网 > PDF目录20640 > ADE7763ARSZ (Analog Devices Inc)IC ENERGY METERING 1PHASE 20SSOP PDF资料下载
参数资料
| 型号： | ADE7763ARSZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 19/56页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METERING 1PHASE 20SSOP |
| 标准包装： | 66 |
| 输入阻抗： | 390 千欧 |
| 测量误差： | 0.1% |
| 电压 - 高输入/输出： | 2.4V |
| 电压 - 低输入/输出： | 0.8V |
| 电流 - 电源： | 3mA |
| 电源电压： | 4.75 V ~ 5.25 V |
| 测量仪表类型： | 单相 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 20-SSOP |
| 包装： | 管件 |
| 产品目录页面： | 797 (CN2011-ZH PDF) |
| 配用： | EVAL-ADE7763ZEB-ND - BOARD EVALUATION FOR ADE7763 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页
Data Sheet
input. Reading the RSTVPEAK and RSTIPEAK registers clears
their respective contents after the read operation.
INTERRUPTS
Interrupts are managed through the interrupt status register
(STATUS[15:0]) and the interrupt enable register
(IRQEN[15:0]). When an interrupt event occurs, the
corresponding flag in the status register is set to Logic 1—see
the Interrupt Status Register section. If the enable bit for this
interrupt in the interrupt enable register is Logic 1, the IRQ
logic output will go active low. The flag bits in the status register
are set irrespective of the state of the enable bits.
To determine the source of the interrupt, the system master
(MCU) should perform a read from the status register with
reset (RSTSTATUS[15:0]). This is achieved by carrying out a
read from Address 0Ch. The IRQ output goes logic high after
the completion of the interrupt status register read command—
see the Interrupt Timing section. When carrying out a read
with reset, the ADE7763 is designed to ensure that no interrupt
events are missed. If an interrupt event occurs as the status
register is being read, the event will not be lost and the IRQ
logic output will be guaranteed to go high for the duration of
the interrupt status register data transfer before going logic low
again to indicate the pending interrupt. See the next section for
a more detailed description.
ADE7763
Using Interrupts with an MCU
mentation of ADE7763 interrupt management using an MCU.
At time t 1 , the IRQ line goes active low, indicating that one or
more interrupt events have occurred. Tie the IRQ logic output to
a negative edge-triggered external interrupt on the MCU.
Configure the MCU to start executing its interrupt service
routine (ISR) when a negative edge is detected on the IRQ line.
After entering the ISR, disable all interrupts by using the global
interrupt enable bit. At this point, the MCU IRQ external
interrupt flag can be cleared to capture interrupt events that
occur during the current ISR. When the MCU interrupt flag is
cleared, a read f rom the status register with reset is carried out.
This causes the IRQ line to reset to logic high (t 2 )—see the
to determine the source of the interrupt(s) and, therefore, the
appropriate action to be taken. If a subsequent interrupt event
occurs during the ISR, that event will be recorded by the MCU
external interrupt flag being set again (t 3 ). Upon the completion
of the ISR, the global interrupt mask is cleared (same
instruction cycle) and the external interrupt flag causes the
MCU to jump to its ISR again. This ensures that the MCU does
not miss any external interrupts.
t 1
t 2
t 3
MCU
INTERRUPT
FLAG SET
IRQ
MCU
PROGRAM
SEQUENCE
JUMP
TO
ISR
GLOBAL
INTERRUPT
MASK SET
CLEAR MCU
INTERRUPT
FLAG
READ
STATUS WITH
RESET (0x0C)
ISR ACTION
(BASED ON STATUS CONTENTS)
ISR RETURN
GLOBAL INTERRUPT
MASK RESET
JUMP
TO
ISR
Figure 37. Interrupt Management
CS
t 1
SCLK
t 9
DIN
0
0
0
0
0
1
0
1
t 11
t 11
DOUT
DB7
DB0 DB7
DB 0
READ STATUS REGISTER COMMAND
STATUS REGISTER CONTENTS
IRQ
Figure 38. Interrupt Timing
Rev. C | Page 19 of 56
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6605IRZ | IC MOSFET DRVR SYNC BUCK 8-QFN |
| CS5463-ISZ | IC ENERGY METERING 1PHASE 24SSOP |
| RGM40DTAD-S189 | CONN EDGECARD 80POS R/A .156 SLD |
| TTN0.38SV100 | THERMASHIELD TUBE 3/8" SLV 100' |
| ADE7751ARSZ | IC ENERGY METERING 1PHASE 24SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADE7763ARSZ | 制造商:Analog Devices 功能描述:IC, SINGLE PHASE ENERGY METER, SSOP-20 |
| ADE7763ARSZRL | 功能描述:IC ENERGY METERING 1PHASE 20SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7763ARSZRL | 制造商:Analog Devices 功能描述:IC, SINGLE PHASE ENERGY METER, SSOP-20 |
| ADE7768 | 制造商:AD 制造商全称:Analog Devices 功能描述:Energy Metering IC with Integrated Oscillator and Positive Power Accumulation |
| ADE7768AR | 制造商:AD 制造商全称:Analog Devices 功能描述:Energy Metering IC with Integrated Oscillator and Positive Power Accumulation |
发布紧急采购，3分钟左右您将得到回复。