- 您现在的位置：买卖IC网 > PDF目录20640 > ADE7763ARSZ (Analog Devices Inc)IC ENERGY METERING 1PHASE 20SSOP PDF资料下载
参数资料
| 型号： | ADE7763ARSZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 28/56页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METERING 1PHASE 20SSOP |
| 标准包装： | 66 |
| 输入阻抗： | 390 千欧 |
| 测量误差： | 0.1% |
| 电压 - 高输入/输出： | 2.4V |
| 电压 - 低输入/输出： | 0.8V |
| 电流 - 电源： | 3mA |
| 电源电压： | 4.75 V ~ 5.25 V |
| 测量仪表类型： | 单相 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 20-SSOP |
| 包装： | 管件 |
| 产品目录页面： | 797 (CN2011-ZH PDF) |
| 配用： | EVAL-ADE7763ZEB-ND - BOARD EVALUATION FOR ADE7763 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页
ADE7763
Data Sheet
HPF
APOS[15:0]
24
FOR WAVEF0RM
SAMPLING
I
sgn 2 6 2 5
2 -6 2 -7 2 -8
0x1 9999
CURRENT SIGNAL – i(t)
MULTIPLIER
24
LPF2
+
+
32
FOR WAVEFORM
ACCUMULATION
V
1
INSTANTANEOUS
POWER SIGNAL – p(t)
WGAIN[11:0]
0xC CCCD
VOLTAGE SIGNAL – v(t)
0x19 999A
0x00 0000
Figure 57. Active Power Signal Processing
The ADE7763 achieves the integration of the active power
signal by continuously accumulating the active power signal in
an internal unreadable 49-bit energy register. The active energy
register (AENERGY[23:0]) represents the upper 24 bits of this
internal register. This discrete time accumulation or summation
is equivalent to integration in continuous time. Equation 14
expresses this relationship.
waveform register by setting MODE[14:13] = 0, 0 and setting
the WSMP bit (Bit 3) in the interrupt enable register to 1. Like
Channel 1 and Channel 2 waveform sampling modes, the
waveform data is available at sample rates of 27.9 kSPS, 14 kSPS,
7 kSPS, or 3.5 kSPS—see Figure 44. The active power waveform
sampling signal has a settling time of approximately 2 ms.
? ?
E ? ? p ( t ) dt ? Lim ? ? p ( nT ) ? T ?
? n ? 1 ?
?
t ? 0
where:
n is the discrete time sample number.
T is the sample period.
The discrete time sample period ( T ) for the accumulation
(14)
(sinusoidal) on the analog inputs. The three curves illustrate the
minimum time for the energy register to roll over when the active
power gain register contents are 0x7FF, 0x000, and 0x800. The
watt gain register is used to carry out power calibration. As
shown, the fastest integration time occurs when the watt gain
register is set to maximum full scale, i.e., 0x7FF.
AENERGY[23:0]
register is 1.1 μs (4/CLKIN). In addition to calculating the
0x7F FFFF
WGAIN = 0x7FF
energy, this integration removes any sinusoidal components
that might be in the active power signal.
0x3F FFFF
WGAIN = 0x000
WGAIN = 0x800
The active power signal in the waveform register is continuously
added to the internal active energy register. This addition is a
0x00 0000
4 6.2
8
12.5
TIME (minutes)
signed addition; therefore, negative energy is subtracted from
the active energy contents. The exception to this is when POAM
is selected in the MODE[15:0] register, in which case only
positive energy contributes to the active energy accumulation—
see the Positive-Only Accumulation Mode section.
The output of the multiplier is divided by WDIV. If the value in
the WDIV register is equal to 0, then the internal active energy
register is divided by 1. WDIV is an 8-bit, unsigned register.
After dividing by WDIV, the active energy is accumulated in a
49-bit internal energy accumulation register. The upper 24 bits
of this register are accessible through a read to the active energy
register (AENERGY[23:0]). A read to the RAENERGY register
returns the content of the AENERGY register, and the upper
the active power signal is accumulated in an internal 49-bit,
signed register. The active power signal can be read from the
0x40 0000
0x80 0000
Figure 58. Energy Register Rollover Time for Full-Scale Power
(Minimum and Maximum Power Gain)
Note that the energy register contents roll over to full-scale
negative (0x80 0000) and continue increasing in value when the
power or energy flow is positive—see Figure 58. Conversely, if
the power was negative, the energy register would underflow to
full-scale positive (0x7F FFFF) and continue decreasing in
value.
By using the interrupt enable register, the ADE7763 can be
configured to issue an interrupt (IRQ) when the active energy
register is more than half full (positive or negative), or when an
overflow or underflow occurs.
Rev. C | Page 28 of 56
相关PDF资料 |
PDF描述 |
|---|---|
| ISL6605IRZ | IC MOSFET DRVR SYNC BUCK 8-QFN |
| CS5463-ISZ | IC ENERGY METERING 1PHASE 24SSOP |
| RGM40DTAD-S189 | CONN EDGECARD 80POS R/A .156 SLD |
| TTN0.38SV100 | THERMASHIELD TUBE 3/8" SLV 100' |
| ADE7751ARSZ | IC ENERGY METERING 1PHASE 24SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADE7763ARSZ | 制造商:Analog Devices 功能描述:IC, SINGLE PHASE ENERGY METER, SSOP-20 |
| ADE7763ARSZRL | 功能描述:IC ENERGY METERING 1PHASE 20SSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7763ARSZRL | 制造商:Analog Devices 功能描述:IC, SINGLE PHASE ENERGY METER, SSOP-20 |
| ADE7768 | 制造商:AD 制造商全称:Analog Devices 功能描述:Energy Metering IC with Integrated Oscillator and Positive Power Accumulation |
| ADE7768AR | 制造商:AD 制造商全称:Analog Devices 功能描述:Energy Metering IC with Integrated Oscillator and Positive Power Accumulation |
发布紧急采购，3分钟左右您将得到回复。