- 您现在的位置：买卖IC网 > PDF目录19388 > ADSP-BF542KBCZ-6A (Analog Devices Inc)IC DSP 16BIT 600MHZ 400CSBGA PDF资料下载
参数资料
| 型号： | ADSP-BF542KBCZ-6A |
| 厂商： | Analog Devices Inc |
| 文件页数： | 2/100页 |
| 文件大小： | 0K |
| 描述： | IC DSP 16BIT 600MHZ 400CSBGA |
| 标准包装： | 1 |
| 系列： | Blackfin® |
| 类型： | 定点 |
| 接口： | CAN，SPI，SSP，TWI，UART，USB |
| 时钟速率： | 600MHz |
| 非易失内存： | 外部 |
| 芯片上RAM： | 132kB |
| 电压 - 输入/输出： | 2.50V，3.30V |
| 电压 - 核心： | 1.25V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 400-LFBGA，CSPBGA |
| 供应商设备封装： | 400-CSPBGA（17x17） |
| 包装： | 托盘 |
| 配用： | ADZS-BF548-EZLITE-ND - KIT EZLITE ADZS-BF548 |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页
Rev. C
|
Page 10 of 100
|
February 2010
ADSP-BF542/ADSP-BF544/ADSP-BF547/ADSP-BF548/ADSP-BF549
Event Control
The ADSP-BF54x Blackfin processors provide the user with a
very flexible mechanism to control the processing of events. In
the CEC, three registers are used to coordinate and control
events. Each register is 16 bits wide:
CEC interrupt latch register (ILAT). The ILAT register
indicates when events have been latched. The appropriate
bit is set when the processor has latched the event and
cleared when the event has been accepted into the system.
This register is updated automatically by the controller, but
it may be written only when its corresponding IMASK bit
is cleared.
CEC interrupt mask register (IMASK). The IMASK regis-
ter controls the masking and unmasking of individual
events. When a bit is set in the IMASK register, that event is
unmasked and is processed by the CEC when asserted. A
cleared bit in the IMASK register masks the event, prevent-
ing the processor from servicing the event even though the
event may be latched in the ILAT register. This register
may be read or written while in supervisor mode. Note that
general-purpose interrupts can be globally enabled and dis-
abled with the STI and CLI instructions, respectively.
CEC interrupt pending register (IPEND). The IPEND reg-
ister keeps track of all nested events. A set bit in the IPEND
register indicates that the event is currently active or nested
at some level. This register is updated automatically by the
controller but may be read while in supervisor mode.
The SIC allows further control of event processing by providing
three 32-bit interrupt control and status registers. Each register
contains a bit corresponding to each of the peripheral interrupt
events shown in Table 4 on Page 8.
SIC interrupt mask registers (SIC_IMASKx). These regis-
ters control the masking and unmasking of each peripheral
interrupt event. When a bit is set in a register, that periph-
eral event is unmasked and is processed by the system
when asserted. A cleared bit in the register masks the
peripheral event, preventing the processor from servicing
the event.
SIC interrupt status registers (SIC_ISRx). As multiple
peripherals can be mapped to a single event, these registers
allow the software to determine which peripheral event
source triggered the interrupt. A set bit indicates the
peripheral is asserting the interrupt, and a cleared bit indi-
cates the peripheral is not asserting the event.
SIC interrupt wakeup enable registers (SIC_IWRx). By
enabling the corresponding bit in this register, a peripheral
can be configured to wake up the processor, should the
core be idled or in Sleep mode when the event is generated.
Because multiple interrupt sources can map to a single general-
purpose interrupt, multiple pulse assertions can occur simulta-
neously, before or during interrupt processing for an interrupt
event already detected on this interrupt input. The IPEND reg-
ister contents are monitored by the SIC as the interrupt
acknowledgement.
The appropriate ILAT register bit is set when an interrupt rising
edge is detected. (Detection requires two core clock cycles.) The
bit is cleared when the respective IPEND register bit is set. The
IPEND bit indicates that the event has entered into the proces-
sor pipeline. At this point the CEC recognizes and queues the
next rising edge event on the corresponding event input. The
minimum latency from the rising edge transition of the general-
purpose interrupt to the IPEND output asserted is three core
clock cycles; however, the latency can be much higher, depend-
ing on the activity within and the state of the processor.
DMA CONTROLLERS
ADSP-BF54x Blackfin processors have multiple, independent
DMA channels that support automated data transfers with min-
imal overhead for the processor core. DMA transfers can occur
between the ADSP-BF54x processors’ internal memories and
any of the DMA-capable peripherals. Additionally, DMA trans-
fers can be accomplished between any of the DMA-capable
peripherals and external devices connected to the external
memory interfaces, including DDR and asynchronous memory
controllers.
While the USB controller and MXVR have their own dedicated
DMA controllers, the other on-chip peripherals are managed by
two centralized DMA controllers, called DMAC1 (32-bit) and
DMAC0 (16-bit). Both operate in the SCLK domain. Each DMA
controller manages 12 independent peripheral DMA channels,
as well as two independent memory DMA streams. The
DMAC1 controller masters high-bandwidth peripherals over a
dedicated 32-bit DMA access bus (DAB32). Similarly, the
DMAC0 controller masters most serial interfaces over the 16-bit
DAB16 bus. Individual DMA channels have fixed access prior-
ity on the DAB buses. DMA priority of peripherals is managed
by a flexible peripheral-to-DMA channel assignment scheme.
All four DMA controllers use the same 32-bit DCB bus to
exchange data with L1 memory. This includes L1 ROM, but
excludes scratchpad memory. Fine granulation of L1 memory
and special DMA buffers minimize potential memory conflicts
when the L1 memory is accessed simultaneously by the core.
Similarly, there are dedicated DMA buses between the external
bus interface unit (EBIU) and the three DMA controllers
(DMAC1, DMAC0, and USB) that arbitrate DMA accesses to
external memories and the boot ROM.
Timer 3 IRQ
89
IVG11
4
Timer 4 IRQ
90
IVG11
4
Timer 5 IRQ
91
IVG11
4
Timer 6 IRQ
92
IVG11
4
Timer 7 IRQ
93
IVG11
4
Pin IRQ 2 (PINT2)
94
IVG12
5
Pin IRQ 3 (PINT3)
95
IVG12
5
Table 4. System Interrupt Controller (SIC) (Continued)
Peripheral IRQ
Source
IRQ
ID
GP IRQ
(at Reset)
Core
IRQ ID
相关PDF资料 |
PDF描述 |
|---|---|
| TPSC686K016S0125 | CAP TANT 68UF 16V 10% 2312 |
| MC7805ACT | IC REG LDO 5V 1A TO220AB |
| VI-B1X-CV-F2 | CONVERTER MOD DC/DC 5.2V 150W |
| VE-B10-CV-F4 | CONVERTER MOD DC/DC 5V 150W |
| ADSP-BF533SBB500 | IC DSP CTLR 16BIT 500MHZ 169-BGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADSP-BF542MBBCZ-5M | 功能描述:IC DSP 16BIT 533MHZ MDDR 400CBGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:Blackfin® 标准包装:2 系列:StarCore 类型:SC140 内核 接口:DSI，以太网，RS-232 时钟速率:400MHz 非易失内存:外部 芯片上RAM:1.436MB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:431-BFBGA，FCBGA 供应商设备封装:431-FCPBGA（20x20） 包装:托盘 |
| ADSP-BF544BBCZ-4A | 功能描述:IC CCD SIGNAL PROCESSOR 400BGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:Blackfin® 标准包装:2 系列:StarCore 类型:SC140 内核 接口:DSI，以太网，RS-232 时钟速率:400MHz 非易失内存:外部 芯片上RAM:1.436MB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:431-BFBGA，FCBGA 供应商设备封装:431-FCPBGA（20x20） 包装:托盘 |
| ADSP-BF544BBCZ-5A | 功能描述:IC DSP 16BIT 533MHZ 400CSBGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:Blackfin® 标准包装:2 系列:StarCore 类型:SC140 内核 接口:DSI，以太网，RS-232 时钟速率:400MHz 非易失内存:外部 芯片上RAM:1.436MB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:431-BFBGA，FCBGA 供应商设备封装:431-FCPBGA（20x20） 包装:托盘 |
| ADSP-BF544BBCZ-5X | 制造商:Analog Devices 功能描述:HIGH PERFORMANCE CONVERGENT MULTIMEDIA BLACKFIN PROCESSOR - Trays |
| ADSP-BF544MBBCZ-5M | 功能描述:IC DSP 16BIT 533MHZ MDDR 400CBGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:Blackfin® 标准包装:2 系列:StarCore 类型:SC140 内核 接口:DSI，以太网，RS-232 时钟速率:400MHz 非易失内存:外部 芯片上RAM:1.436MB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:431-BFBGA，FCBGA 供应商设备封装:431-FCPBGA（20x20） 包装:托盘 |
发布紧急采购，3分钟左右您将得到回复。