- 您现在的位置：买卖IC网 > PDF目录19388 > ADSP-BF542KBCZ-6A (Analog Devices Inc)IC DSP 16BIT 600MHZ 400CSBGA PDF资料下载
参数资料
| 型号： | ADSP-BF542KBCZ-6A |
| 厂商： | Analog Devices Inc |
| 文件页数： | 5/100页 |
| 文件大小： | 0K |
| 描述： | IC DSP 16BIT 600MHZ 400CSBGA |
| 标准包装： | 1 |
| 系列： | Blackfin® |
| 类型： | 定点 |
| 接口： | CAN，SPI，SSP，TWI，UART，USB |
| 时钟速率： | 600MHz |
| 非易失内存： | 外部 |
| 芯片上RAM： | 132kB |
| 电压 - 输入/输出： | 2.50V，3.30V |
| 电压 - 核心： | 1.25V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 400-LFBGA，CSPBGA |
| 供应商设备封装： | 400-CSPBGA（17x17） |
| 包装： | 托盘 |
| 配用： | ADZS-BF548-EZLITE-ND - KIT EZLITE ADZS-BF548 |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页
Rev. C
|
Page 12 of 100
|
February 2010
ADSP-BF542/ADSP-BF544/ADSP-BF547/ADSP-BF548/ADSP-BF549
Connect RTC pins RTXI and RTXO with external components
as shown in Figure 4.
WATCHDOG TIMER
The ADSP-BF54x processors include a 32-bit timer that can be
used to implement a software watchdog function. A software
watchdog can improve system reliability by forcing the proces-
sor to a known state through generation of a hardware reset,
non-maskable interrupt (NMI), or general-purpose interrupt if
the timer expires before being reset by software. The program-
mer initializes the count value of the timer, enables the
appropriate interrupt, and then enables the timer. Thereafter,
the software must reload the counter before it counts to zero
from the programmed value. This protects the system from
remaining in an unknown state where software, which would
normally reset the timer, has stopped running due to an external
noise condition or software error.
If configured to generate a hardware reset, the watchdog timer
resets both the core and the ADSP-BF54x processors’ peripher-
als. After a reset, software can determine if the watchdog was the
source of the hardware reset by interrogating a status bit in the
watchdog timer control register.
The timer is clocked by the system clock (SCLK) at a maximum
frequency of fSCLK.
TIMERS
There are up to two timer units in the ADSP-BF54x Blackfin
processors. One unit provides eight general-purpose program-
mable timers, and the other unit provides three. Each timer has
an external pin that can be configured either as a pulse width
modulator (PWM) or timer output, as an input to clock the
timer, or as a mechanism for measuring pulse widths and peri-
ods of external events. These timers can be synchronized to an
external clock input on the TMRx pins, an external clock
TMRCLK input pin, or to the internal SCLK.
The timer units can be used in conjunction with the four
UARTs and the CAN controllers to measure the width of the
pulses in the data stream to provide a software auto-baud detect
function for the respective serial channels.
The timers can generate interrupts to the processor core, pro-
viding periodic events for synchronization to either the system
clock or to a count of external signals.
In addition to the general-purpose programmable timers,
another timer is also provided by the processor core. This extra
timer is clocked by the internal processor clock and is typically
used as a system tick clock for generation of periodic operating
system interrupts.
UP/DOWN COUNTER AND THUMBWHEEL
INTERFACE
A 32-bit up/down counter is provided that can sense the 2-bit
quadrature or binary codes typically emitted by industrial drives
or manual thumb wheels. The counter can also operate in
general-purpose up/down count modes. Then count direction is
either controlled by a level-sensitive input pin or by two edge
detectors.
A third input can provide flexible zero marker support and can
alternatively be used to input the push-button signal of thumb
wheels. All three pins have a programmable debouncing circuit.
An internal signal forwarded to the timer unit enables one timer
to measure the intervals between count events. Boundary regis-
ters enable auto-zero operation or simple system warning by
interrupts when programmable count values are exceeded.
SERIAL PORTS (SPORTS)
The ADSP-BF54x Blackfin processors incorporate up to four
dual-channel synchronous serial ports (SPORT0, SPORT1,
SPORT2, and SPORT3) for serial and multiprocessor commu-
nications. The SPORTs support the following features:
I2S capable operation.
Bidirectional operation. Each SPORT has two sets of inde-
pendent transmit and receive pins, enabling up to eight
channels of I2S stereo audio.
Buffered (8-deep) transmit and receive ports. Each port has
a data register for transferring data words to and from
other processor components and shift registers for shifting
data in and out of the data registers.
Clocking. Each transmit and receive port can either use an
external serial clock or generate its own, in frequencies
ranging from (fSCLK/131,070) Hz to (fSCLK/2) Hz.
Word length. Each SPORT supports serial data words from
3 to 32 bits in length, transferred most-significant-bit first
or least-significant-bit first.
Framing. Each transmit and receive port can run with or
without frame sync signals for each data word. Frame sync
signals can be generated internally or externally, active high
or low, and with either of two pulse widths and early or late
frame sync.
Figure 4. External Components for RTC
RTXO
C1
C2
X1
SUGGESTED COMPONENTS:
ECLIPTEK EC38J (THROUGH-HOLE PACKAGE)
EPSON MC405 12 pF LOAD (SURFACE-MOUNT PACKAGE)
C1 = 22 pF
C2 = 22 pF
R1 = 10 M
NOTE: C1 AND C2 ARE SPECIFIC TO CRYSTAL SPECIFIED FOR X1.
CONTACT CRYSTAL MANUFACTURER FOR DETAILS. C1 AND C2
SPECIFICATIONS ASSUME BOARD TRACE CAPACITANCE OF 3 pF.
RTXI
R1
相关PDF资料 |
PDF描述 |
|---|---|
| TPSC686K016S0125 | CAP TANT 68UF 16V 10% 2312 |
| MC7805ACT | IC REG LDO 5V 1A TO220AB |
| VI-B1X-CV-F2 | CONVERTER MOD DC/DC 5.2V 150W |
| VE-B10-CV-F4 | CONVERTER MOD DC/DC 5V 150W |
| ADSP-BF533SBB500 | IC DSP CTLR 16BIT 500MHZ 169-BGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADSP-BF542MBBCZ-5M | 功能描述:IC DSP 16BIT 533MHZ MDDR 400CBGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:Blackfin® 标准包装:2 系列:StarCore 类型:SC140 内核 接口:DSI，以太网，RS-232 时钟速率:400MHz 非易失内存:外部 芯片上RAM:1.436MB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:431-BFBGA，FCBGA 供应商设备封装:431-FCPBGA（20x20） 包装:托盘 |
| ADSP-BF544BBCZ-4A | 功能描述:IC CCD SIGNAL PROCESSOR 400BGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:Blackfin® 标准包装:2 系列:StarCore 类型:SC140 内核 接口:DSI，以太网，RS-232 时钟速率:400MHz 非易失内存:外部 芯片上RAM:1.436MB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:431-BFBGA，FCBGA 供应商设备封装:431-FCPBGA（20x20） 包装:托盘 |
| ADSP-BF544BBCZ-5A | 功能描述:IC DSP 16BIT 533MHZ 400CSBGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:Blackfin® 标准包装:2 系列:StarCore 类型:SC140 内核 接口:DSI，以太网，RS-232 时钟速率:400MHz 非易失内存:外部 芯片上RAM:1.436MB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:431-BFBGA，FCBGA 供应商设备封装:431-FCPBGA（20x20） 包装:托盘 |
| ADSP-BF544BBCZ-5X | 制造商:Analog Devices 功能描述:HIGH PERFORMANCE CONVERGENT MULTIMEDIA BLACKFIN PROCESSOR - Trays |
| ADSP-BF544MBBCZ-5M | 功能描述:IC DSP 16BIT 533MHZ MDDR 400CBGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:Blackfin® 标准包装:2 系列:StarCore 类型:SC140 内核 接口:DSI，以太网，RS-232 时钟速率:400MHz 非易失内存:外部 芯片上RAM:1.436MB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:431-BFBGA，FCBGA 供应商设备封装:431-FCPBGA（20x20） 包装:托盘 |
发布紧急采购，3分钟左右您将得到回复。