- 您现在的位置：买卖IC网 > PDF目录19388 > ADSP-BF542KBCZ-6A (Analog Devices Inc)IC DSP 16BIT 600MHZ 400CSBGA PDF资料下载
参数资料
| 型号： | ADSP-BF542KBCZ-6A |
| 厂商： | Analog Devices Inc |
| 文件页数： | 7/100页 |
| 文件大小： | 0K |
| 描述： | IC DSP 16BIT 600MHZ 400CSBGA |
| 标准包装： | 1 |
| 系列： | Blackfin® |
| 类型： | 定点 |
| 接口： | CAN，SPI，SSP，TWI，UART，USB |
| 时钟速率： | 600MHz |
| 非易失内存： | 外部 |
| 芯片上RAM： | 132kB |
| 电压 - 输入/输出： | 2.50V，3.30V |
| 电压 - 核心： | 1.25V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 400-LFBGA，CSPBGA |
| 供应商设备封装： | 400-CSPBGA（17x17） |
| 包装： | 托盘 |
| 配用： | ADZS-BF548-EZLITE-ND - KIT EZLITE ADZS-BF548 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页
Rev. C
|
Page 14 of 100
|
February 2010
ADSP-BF542/ADSP-BF544/ADSP-BF547/ADSP-BF548/ADSP-BF549
The ADSP-BF54x Blackfin processors’ CAN controllers offer
the following features:
32 mailboxes (8 receive only, 8 transmit only, 16 config-
urable for receive or transmit).
Dedicated acceptance masks for each mailbox.
Additional data filtering on first two bytes.
Support for both the standard (11-bit) and extended (29-
bit) identifier (ID) message formats.
Support for remote frames.
Active or passive network support.
CAN wakeup from hibernation mode (lowest static power
consumption mode).
Interrupts, including: TX complete, RX complete, error
and global.
The electrical characteristics of each network connection are
very demanding, so the CAN interface is typically divided into
two parts: a controller and a transceiver. This allows a single
controller to support different drivers and CAN networks. The
ADSP-BF54x Blackfin processors’ CAN module represents only
the controller part of the interface. The controller interface sup-
ports connection to 3.3 V high speed, fault-tolerant, single-wire
transceivers.
An additional crystal is not required to supply the CAN clock, as
the CAN clock is derived from the processor system clock
(SCLK) through a programmable divider.
TWI CONTROLLER INTERFACE
The ADSP-BF54x Blackfin processors include up to two 2-wire
interface (TWI) modules for providing a simple exchange
method of control data between multiple devices. The modules
are compatible with the widely used I2C bus standard. The TWI
modules offer the capabilities of simultaneous master and slave
operation and support for both 7-bit addressing and multime-
dia data arbitration. Each TWI interface uses two pins for
transferring clock (SCLx) and data (SDAx), and supports the
protocol at speeds up to 400K bits/sec. The TWI interface pins
are compatible with 5 V logic levels.
Additionally, the ADSP-BF54x Blackfin processors’ TWI mod-
ules are fully compatible with serial camera control bus (SCCB)
functionality for easier control of various CMOS camera sensor
devices.
PORTS
Because of their rich set of peripherals, the ADSP-BF54x
Blackfin processors group the many peripheral signals to ten
ports—referred to as Port A to Port J. Most ports contain 16
pins, though some have fewer. Many of the associated pins are
shared by multiple signals. The ports function as multiplexer
controls. Every port has its own set of memory-mapped regis-
ters to control port muxing and GPIO functionality.
General-Purpose I/O (GPIO)
Every pin in Port A to Port J can function as a GPIO pin, result-
ing in a GPIO pin count up to 154. While it is unlikely that all
GPIO pins will be used in an application, as all pins have multi-
ple functions, the richness of GPIO functionality guarantees
unrestrictive pin usage. Every pin that is not used by any func-
tion can be configured in GPIO mode on an individual basis.
After reset, all pins are in GPIO mode by default. Since neither
GPIO output nor input drivers are active by default, unused
pins can be left unconnected. GPIO data and direction control
registers provide flexible write-one-to-set and write-one-to-
clear mechanisms so that independent software threads do not
need to protect against each other because of expensive read-
modify-write operations when accessing the same port.
Pin Interrupts
Every port pin on ADSP-BF54x Blackfin processors can request
interrupts in either an edge-sensitive or a level-sensitive manner
with programmable polarity. Interrupt functionality is decou-
pled from GPIO operation. Four system-level interrupt
channels (PINT0, PINT1, PINT2 and PINT3) are reserved for
this purpose. Each of these interrupt channels can manage up to
32 interrupt pins. The assignment from pin to interrupt is not
performed on a pin-by-pin basis. Rather, groups of eight pins
(half ports) can be flexibly assigned to interrupt channels.
Every pin interrupt channel features a special set of 32-bit mem-
ory-mapped registers that enables half-port assignment and
interrupt management. This not only includes masking, identi-
fication, and clearing of requests, it also enables access to the
respective pin states and use of the interrupt latches regardless
of whether the interrupt is masked or not. Most control registers
feature multiple MMR address entries to write-one-to-set or
write-one-to-clear them individually.
PIXEL COMPOSITOR (PIXC)
The pixel compositor (PIXC) provides image overlays with
transparent-color support, alpha blending, and color space con-
version capabilities for output to TFT LCDs and NTSC/PAL
video encoders. It provides all of the control to allow two data
streams from two separate data buffers to be combined,
blended, and converted into appropriate forms for both LCD
panels and digital video outputs. The main image buffer pro-
vides the basic background image, which is presented in the
data stream. The overlay image buffer allows the user to add
multiple foreground text, graphics, or video objects on top of
the main image or video data stream.
ENHANCED PARALLEL PERIPHERAL INTERFACE
(EPPI)
The ADSP-BF54x Blackfin processors provide up to three
enhanced parallel peripheral interfaces (EPPIs), supporting data
widths up to 24 bits. The EPPI supports direct connection to
TFT LCD panels, parallel analog-to-digital and digital-to-ana-
log converters, video encoders and decoders, image sensor
modules and other general-purpose peripherals.
相关PDF资料 |
PDF描述 |
|---|---|
| TPSC686K016S0125 | CAP TANT 68UF 16V 10% 2312 |
| MC7805ACT | IC REG LDO 5V 1A TO220AB |
| VI-B1X-CV-F2 | CONVERTER MOD DC/DC 5.2V 150W |
| VE-B10-CV-F4 | CONVERTER MOD DC/DC 5V 150W |
| ADSP-BF533SBB500 | IC DSP CTLR 16BIT 500MHZ 169-BGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADSP-BF542MBBCZ-5M | 功能描述:IC DSP 16BIT 533MHZ MDDR 400CBGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:Blackfin® 标准包装:2 系列:StarCore 类型:SC140 内核 接口:DSI，以太网，RS-232 时钟速率:400MHz 非易失内存:外部 芯片上RAM:1.436MB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:431-BFBGA，FCBGA 供应商设备封装:431-FCPBGA（20x20） 包装:托盘 |
| ADSP-BF544BBCZ-4A | 功能描述:IC CCD SIGNAL PROCESSOR 400BGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:Blackfin® 标准包装:2 系列:StarCore 类型:SC140 内核 接口:DSI，以太网，RS-232 时钟速率:400MHz 非易失内存:外部 芯片上RAM:1.436MB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:431-BFBGA，FCBGA 供应商设备封装:431-FCPBGA（20x20） 包装:托盘 |
| ADSP-BF544BBCZ-5A | 功能描述:IC DSP 16BIT 533MHZ 400CSBGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:Blackfin® 标准包装:2 系列:StarCore 类型:SC140 内核 接口:DSI，以太网，RS-232 时钟速率:400MHz 非易失内存:外部 芯片上RAM:1.436MB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:431-BFBGA，FCBGA 供应商设备封装:431-FCPBGA（20x20） 包装:托盘 |
| ADSP-BF544BBCZ-5X | 制造商:Analog Devices 功能描述:HIGH PERFORMANCE CONVERGENT MULTIMEDIA BLACKFIN PROCESSOR - Trays |
| ADSP-BF544MBBCZ-5M | 功能描述:IC DSP 16BIT 533MHZ MDDR 400CBGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:Blackfin® 标准包装:2 系列:StarCore 类型:SC140 内核 接口:DSI，以太网，RS-232 时钟速率:400MHz 非易失内存:外部 芯片上RAM:1.436MB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:431-BFBGA，FCBGA 供应商设备封装:431-FCPBGA（20x20） 包装:托盘 |
发布紧急采购，3分钟左右您将得到回复。