- 您现在的位置：买卖IC网 > PDF目录19369 > ADSP-TS201SABP-060 (Analog Devices Inc)IC PROCESSOR 600MHZ 576BGA PDF资料下载
参数资料
| 型号： | ADSP-TS201SABP-060 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/48页 |
| 文件大小： | 0K |
| 描述： | IC PROCESSOR 600MHZ 576BGA |
| 标准包装： | 1 |
| 系列： | TigerSHARC® |
| 类型： | 定点/浮点 |
| 接口： | 主机接口，连接端口，多处理器 |
| 时钟速率： | 600MHz |
| 非易失内存： | 外部 |
| 芯片上RAM： | 3MB |
| 电压 - 输入/输出： | 2.50V |
| 电压 - 核心： | 1.20V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 576-BBGA 裸露焊盘 |
| 供应商设备封装： | 576-BGA-ED（25x25） |
| 包装： | 托盘 |
| 配用： | ADZS-TS201S-EZLITE-ND - KIT LITE EVAL FOR ADSP-TS201S |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
Rev. C
|
Page 18 of 48
|
December 2006
ADSP-TS201S
Table 11. Pin Definitions—Link Ports
Signal
Type
Term
Description
LxDATO3–0P
O
nc
Link Ports 3–0 Data 3–0 Transmit LVDS P
LxDATO3–0N
O
nc
Link Ports 3–0 Data 3–0 Transmit LVDS N
LxCLKOUTP
O
nc
Link Ports 3–0 Transmit Clock LVDS P
LxCLKOUTN
O
nc
Link Ports 3–0 Transmit Clock LVDS N
LxACKI
I (pd)
nc
Link Ports 3–0 Receive Acknowledge. Using this signal, the receiver indicates to the
transmitter that it may continue the transmission.
LxBCMPO
O (pu)
nc
Link Ports 3–0 Block Completion. When the transmission is executed using DMA, this
signal indicates to the receiver that the transmitted block is completed. The pull-up
resistor is present on L0BCMPO only. At reset, the L1BCMPO, L2BCMPO, and L3BCMPO
pins are strap pins. For more information, see Table 16 on Page 20.
LxDATI3–0P
I
VDD_IO
Link Ports 3–0 Data 3–0 Receive LVDS P
LxDATI3–0N
I
VDD_IO
Link Ports 3–0 Data 3–0 Receive LVDS N
LxCLKINP
I/A
VDD_IO
Link Ports 3–0 Receive Clock LVDS P
LxCLKINN
I/A
VDD_IO
Link Ports 3–0 Receive Clock LVDS N
LxACKO
O
nc
Link Ports 3–0 Transmit Acknowledge. Using this signal, the receiver indicates to the
transmitter that it may continue the transmission.
LxBCMPI
I (pd_l)
VSS
Link Ports 3–0 Block Completion. When the reception is executed using DMA, this
signal indicates to the receiver that the transmitted block is completed.
I = input; A = asynchronous; O = output; OD = open-drain output; T = three-state; P = power supply; G = ground; pd = internal pull-down
5k
Ω; pu = internal pull-up 5 kΩ; pd_0 = internal pull-down 5 kΩ on DSP ID = 0; pu_0 = internal pull-up 5 kΩ on DSP ID = 0; pu_od_0 = internal
pull-up 500
Ω on DSP ID = 0; pd_m = internal pull-down 5 kΩ on DSP bus master; pu_m = internal pull-up 5 kΩ on DSP bus master; pu_ad
= internal pull-up 40 k
Ω; pd_l = internal pull-down 50 kΩ. For more pull-down and pull-up information, see Electrical Characteristics on
Term (termination of unused pins) column symbols: epd = external pull-down approximately 5 k
Ω to VSS; epu = external pull-up approx-
imately 5 k
Ω to VDD_IO, nc = not connected; na = not applicable (always used); VDD_IO = connect directly to VDD_IO; VSS = connect directly to VSS
Table 12. Pin Definitions—Impedance Control, Drive Strength Control, and Regulator Enable
Signal
Type
Term
Description
CONTROLIMP0
CONTROLIMP1
I (pd)
I (pu)
na
Impedance Control. As shown in Table 13, the CONTROLIMP1–0 pins select between
normal driver mode and A/D driver mode. When using normal mode (recommended),
the output drive strength is set relative to maximum drive strength according to
Table 14. When using A/D mode, the resistance control operates in the analog mode,
where drive strength is continuously controlled to match a specific line impedance as
shown in Table 14.
DS2, 0
DS1
I (pu)
I (pd)
na
Digital Drive Strength Selection. Selected as shown in Table 14. For drive strength calcu-
lation, see Output Drive Currents on Page 36. The drive strength for some pins is preset,
not controlled by the DS2–0 pins. The pins that are always at drive strength 7 (100%)
include: CPA, DPA, TDO, EMU, and RST_OUT. The drive strength for the ACK pin is always
x2 drive strength 7 (100%).
ENEDREG
I (pu)
VSS
Connect the ENEDREG pin to VSS. Connect the VDD_DRAM pins to a properly decoupled
DRAM power supply.
I = input; A = asynchronous; O = output; OD = open-drain output; T = three-state; P = power supply; G = ground; pd = internal pull-down
5k
Ω; pu = internal pull-up 5 kΩ; pd_0 = internal pull-down 5 kΩ on DSP ID = 0; pu_0 = internal pull-up 5 kΩ on DSP ID = 0; pu_od_0 = internal
pull-up 500
Ω on DSP ID = 0; pd_m = internal pull-down 5 kΩ on DSP bus master; pu_m = internal pull-up 5 kΩ on DSP bus master; pu_ad
= internal pull-up 40 k
Ω. For more pull-down and pull-up information, see Electrical Characteristics on Page 22.
Term (termination of unused pins) column symbols: epd = external pull-down approximately 5 k
Ω to VSS; epu = external pull-up approx-
imately 5 k
Ω to VDD_IO, nc = not connected; na = not applicable (always used); VDD_IO = connect directly to VDD_IO; VSS = connect directly to VSS
相关PDF资料 |
PDF描述 |
|---|---|
| VE-B3H-CY-S | CONVERTER MOD DC/DC 52V 50W |
| ADSP-21060KSZ-133 | IC DSP CONTROLLER 32BIT 240-MQFP |
| EBC25DRTS | CONN EDGECARD 50POS DIP .100 SLD |
| VE-B3D-CY-S | CONVERTER MOD DC/DC 85V 50W |
| TPSD686K020R0200 | CAP TANT 68UF 20V 10% 2917 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADSP-TS201SABP-10X | 制造商:Analog Devices 功能描述: |
| ADSP-TS201SABP-15X | 制造商:Analog Devices 功能描述: |
| ADSP-TS201SABP-ENG | 制造商:Analog Devices 功能描述: |
| ADSP-TS201SABP-ENG1 | 制造商:Analog Devices 功能描述: |
| ADSP-TS201SABPZ050 | 功能描述:IC PROCESSOR 500MHZ 576BGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:TigerSHARC® 标准包装:2 系列:StarCore 类型:SC140 内核 接口:DSI，以太网，RS-232 时钟速率:400MHz 非易失内存:外部 芯片上RAM:1.436MB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:431-BFBGA，FCBGA 供应商设备封装:431-FCPBGA（20x20） 包装:托盘 |
发布紧急采购，3分钟左右您将得到回复。