- 您现在的位置：买卖IC网 > PDF目录12018 > ADUC812BSZ (Analog Devices Inc)IC ADC 12BIT MULTICH MCU 52-MQFP PDF资料下载
参数资料
| 型号： | ADUC812BSZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 22/57页 |
| 文件大小： | 0K |
| 描述： | IC ADC 12BIT MULTICH MCU 52-MQFP |
| 产品培训模块： | Process Control |
| 标准包装： | 1 |
| 系列： | MicroConverter® ADuC8xx |
| 核心处理器： | 8052 |
| 芯体尺寸： | 8-位 |
| 速度： | 16MHz |
| 连通性： | I²C，SPI，UART/USART |
| 外围设备： | PSM，温度传感器，WDT |
| 输入/输出数： | 34 |
| 程序存储器容量： | 8KB（8K x 8） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 640 x 8 |
| RAM 容量： | 256 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.7 V ~ 5.5 V |
| 数据转换器： | A/D 8x12b，D/A 2x12b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 52-QFP |
| 包装： | 托盘 |
| 产品目录页面： | 738 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页
REV.
ADuC812
–29–
8051 COMPATIBLE ON-CHIP PERIPHERALS
This section gives a brief overview of the various secondary
peripheral circuits that are also available to the user on-chip.
These remaining functions are fully 8051 compatible and are
controlled via standard 8051 SFR bit definitions.
Parallel I/O Ports 0–3
The ADuC812 uses four input/output ports to exchange data with
external devices. In addition to performing general-purpose I/O,
some ports are capable of external memory operations; others
are multiplexed with an alternate function for the peripheral
features on the device. In general, when a peripheral is enabled,
that pin may not be used as a general-purpose I/O pin.
Port 0 is an 8-bit, open-drain, bidirectional I/O port that is directly
controlled via the P0 SFR (SFR address = 80H). Port 0 pins
that have 1s written to them via the Port 0 SFR will be configured
as open-drain and will therefore float. In that state, Port 0 pins can
be used as high impedance inputs. An external pull-up resistor
will be required on Port 0 outputs to force a valid logic high
level externally. Port 0 is also the multiplexed low order address
and data bus during accesses to external program or data memory.
In this application, it uses strong internal pull-ups when emitting 1s.
Port 1 is also an 8-bit port directly controlled via the P1 SFR
(SFR address = 90H). Port 1 is an input only port. Port 1 digital
output capability is not supported on this device. Port 1 pins can
be configured as digital inputs or analog inputs.
By (power-on) default these pins are configured as analog inputs,
i.e., “1” written in the corresponding Port 1 register bit. To
configure any of these pins as digital inputs, the user should write
a “0” to these port bits to configure the corresponding pin as a
high impedance digital input.
These pins also have various secondary functions described in
Table XIII.
Table XIII. Port 1, Alternate Pin Functions
Pin
Alternate Function
P1.0
T2 (Timer/Counter 2 External Input)
P1.1
T2EX (Timer/Counter 2 Capture/Reload Trigger)
P1.5
SS (Slave Select for the SPI Interface)
Port 2 is a bidirectional port with internal pull-up resistors directly
controlled via the P2 SFR (SFR address = A0H). Port 2 pins
that have 1s written to them are pulled high by the internal pull-up
resistors and, in that state, can be used as inputs. As inputs, Port
2 pins being pulled externally low will source current because of
the internal pull-up resistors. Port 2 emits the high order
address bytes during fetches from external program memory,
and middle and high order address bytes during accesses to the
24-bit external data memory space.
Port 3 is a bidirectional port with internal pull-ups directly
controlled via the P3 SFR (SFR address = B0H). Port 3 pins
that have 1s written to them are pulled high by the internal pull-ups
and, in that state, can be used as inputs. As inputs, Port 3 pins
being pulled externally low will source current because of the internal
pull-ups. Port 3 pins also have various secondary functions
described in Table XIV.
Table XIV. Port 3, Alternate Pin Functions
Pin
Alternate Function
P3.0
RxD (UART Input Pin)
(or Serial Data I/O in Mode 0)
P3.1
TxD (UART Output Pin)
(or Serial Clock Output in Mode 0)
P3.2
INT0 (External Interrupt 0)
P3.3
INT1 (External Interrupt 1)
P3.4
T0 (Timer/Counter 0 External Input)
P3.5
T1 (Timer/Counter 1 External Input)
P3.6
WR (External Data Memory Write Strobe)
P3.7
RD (External Data Memory Read Strobe)
The alternate functions of P1.0, P1.1, P1.5, and Port 3 pins
can be activated only if the corresponding bit latch in the P1
and P3 SFRs contains a 1. Otherwise, the port pin is stuck at 0.
Timers/Counters
The ADuC812 has three 16-bit Timer/Counters: Timer 0,
Timer 1, and Timer 2. The Timer/Counter hardware has been
included on-chip to relieve the processor core of the overhead
inherent in implementing timer/counter functionality in software.
Each Timer/Counter consists of two 8-bit registers, THx and
TLx (x = 0, 1, and 2). All three can be configured to operate
either as timers or event counters.
In Timer function, the TLx register is incremented every machine
cycle. Thus, think of it as counting machine cycles. Since a
machine cycle consists of 12 core clock periods, the maximum
count rate is 1/12 of the core clock frequency.
In Counter function, the TLx register is incremented by a 1-to-0
transition at its corresponding external input pin, T0, T1, or T2.
In this function, the external input is sampled during S5P2 of
every machine cycle. When the samples show a high in one cycle and
a low in the next cycle, the count is incremented. The new count
value appears in the register during S3P1 of the cycle following the
one in which the transition was detected. Since it takes two machine
cycles (24 core clock periods) to recognize a 1-to-0 transition,
the maximum count rate is 1/24 of the core clock frequency.
There are no restrictions on the duty cycle of the external input
signal, but to ensure that a given level is sampled at least once
before it changes, it must be held for a minimum of one full
machine cycle.
F
相关PDF资料 |
PDF描述 |
|---|---|
| AT32UC3C1512C-AZT | IC MCU 32BIT 512KB FLASH 100TQFP |
| VI-JVP-IY-F3 | CONVERTER MOD DC/DC 13.8V 50W |
| VE-233-IY-F2 | CONVERTER MOD DC/DC 24V 50W |
| VE-233-IY-F1 | CONVERTER MOD DC/DC 24V 50W |
| VE-2NY-IW-F1 | CONVERTER MOD DC/DC 3.3V 66W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUC812BSZ-01 | 制造商:Analog Devices 功能描述:12-BIT ADC WITH EMBEDDED MCU I.C. |
| ADUC812BSZ-REEL | 功能描述:IC MCU FLASH 12BIT ADC 52MQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
| ADUC813BS | 制造商:Analog Devices 功能描述:12-BIT ADC WITH EMBEDDED MCU I.C. - Trays |
| ADUC814 | 制造商:AD 制造商全称:Analog Devices 功能描述:MicroConverter, Small Package 12-Bit ADC with Embedded Flash MCU |
| ADUC814_02 | 制造商:AD 制造商全称:Analog Devices 功能描述:MicroConverter, Small Package 12-Bit ADC with Embedded FLASH MCU |
发布紧急采购，3分钟左右您将得到回复。