参数资料
型号: ADUC812BSZ
厂商: Analog Devices Inc
文件页数: 40/57页
文件大小: 0K
描述: IC ADC 12BIT MULTICH MCU 52-MQFP
产品培训模块: Process Control
标准包装: 1
系列: MicroConverter® ADuC8xx
核心处理器: 8052
芯体尺寸: 8-位
速度: 16MHz
连通性: I²C,SPI,UART/USART
外围设备: PSM,温度传感器,WDT
输入/输出数: 34
程序存储器容量: 8KB(8K x 8)
程序存储器类型: 闪存
EEPROM 大小: 640 x 8
RAM 容量: 256 x 8
电压 - 电源 (Vcc/Vdd): 2.7 V ~ 5.5 V
数据转换器: A/D 8x12b,D/A 2x12b
振荡器型: 内部
工作温度: -40°C ~ 85°C
封装/外壳: 52-QFP
包装: 托盘
产品目录页面: 738 (CN2011-ZH PDF)
REV.
ADuC812
–45–
Note that the serial port debugger is fully contained on the
ADuC812 device, (unlike ROM monitor type debuggers) and
therefore no external memory is needed to enable in-system
debug sessions.
Single-Pin Emulation Mode
Also built into the ADuC812 is a dedicated controller for single-pin
in-circuit emulation (ICE) using standard production ADuC812
devices. In this mode, emulation access is gained by connection
to a single pin, the
EA pin. Normally, this pin is hardwired either
high or low to select execution from internal or external program
memory space, as described earlier. To enable single-pin emulation
mode, however, users will need to pull the
EA pin high through
a 1 k resistor, as shown in Figure 46. The emulator will then
connect to the 2-pin header also shown in Figure 46. To be com-
patible with the standard connector that comes with the single-pin
emulator available from Accutron Limited (www.accutron.com),
use a 2-pin 0.1 inch pitch “Friction Lock” header from Molex
(www.molex.com) such as their part number 22-27-2021. Be sure
to observe the polarity of this header. As represented in Figure 46,
when the Friction Lock tab is at the right, the ground pin should
be the lower of the two pins (when viewed from the top).
Enhanced-Hooks Emulation Mode
ADuC812 also supports enhanced-hooks emulation mode. An
enhanced-hooks based emulator is available from Metalink
Corporation (www.metaice.com). No special hardware support
for these emulators needs to be designed onto the board since
these are pod-style emulators where users must replace the chip
on their board with a header device that the emulator pod plugs
into. The only hardware concern is then one of determining if
adequate space is available for the emulator pod to fit into the
system enclosure.
Typical System Configuration
A typical ADuC812 configuration is shown in Figure 46. It sum-
marizes some of the hardware considerations discussed in the
previous paragraphs.
QUICKSTART DEVELOPMENT SYSTEM
The QuickStart Development System is a full featured, low cost
development tool suite supporting the ADuC812. The system
consists of the following PC based (Windows
compatible)
hardware and software development tools.
Hardware:
ADuC812 Evaluation Board, Plug-In
Power Supply and Serial Port Cable
Code Development:
8051 Assembler
Code Functionality:
Windows Based Simulator
In-Circuit Code Download: Serial Downloader
In-Circuit Debugger:
Serial Port Debugger
Miscellaneous Other:
CD-ROM Documentation and
Two Additional Prototype Devices
Figure 47 shows the typical components of a QuickStart
Development System. A brief description of some of the software
tools components in the QuickStart Development System is
given in the following sections.
Figure 47. Components of the QuickStart Development
System
Figure 48. Typical Debug Session
Download—In-Circuit Serial Downloader
The Serial Downloader is a Windows application that allows the
user to serially download an assembled program (Intel Hex format
file) to the on-chip program FLASH memory via the serial COM1
port on a standard PC. Application Note uC004 detailing this
serial download protocol is available at www.analog.com/
microconverter.
DeBug—In-Circuit Debugger
The Debugger is a Windows application that allows the user to
debug code execution on silicon using the MicroConverter UART
serial port. The debugger provides access to all on-chip periph-
erals during a typical debug session as well as single-step and
breakpoint code execution control.
ADSIM—Windows Simulator
The Simulator is a Windows application that fully simulates all
the MicroConverter functionality including ADC and DAC
peripherals. The simulator provides an easy-to-use, intuitive inter-
face to the MicroConverter functionality and integrates many
standard debug features including multiple breakpoints, single
stepping, and code execution trace capability. This tool can be
used both as a tutorial guide to the part as well as an efficient way
to prove code functionality before moving to a hardware platform.
The QuickStart development tool suite software is freely available at
the Analog Devices MicroConverter website, www.analog.com/
microconverter.
F
相关PDF资料
PDF描述
AT32UC3C1512C-AZT IC MCU 32BIT 512KB FLASH 100TQFP
VI-JVP-IY-F3 CONVERTER MOD DC/DC 13.8V 50W
VE-233-IY-F2 CONVERTER MOD DC/DC 24V 50W
VE-233-IY-F1 CONVERTER MOD DC/DC 24V 50W
VE-2NY-IW-F1 CONVERTER MOD DC/DC 3.3V 66W
相关代理商/技术参数
参数描述
ADUC812BSZ-01 制造商:Analog Devices 功能描述:12-BIT ADC WITH EMBEDDED MCU I.C.
ADUC812BSZ-REEL 功能描述:IC MCU FLASH 12BIT ADC 52MQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:MicroConverter® ADuC8xx 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA,UART/USART 外围设备:欠压检测/复位,LED,POR,PWM,WDT 输入/输出数:16 程序存储器容量:4KB(4K x 8) 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC(0.295",7.50mm 宽) 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND
ADUC813BS 制造商:Analog Devices 功能描述:12-BIT ADC WITH EMBEDDED MCU I.C. - Trays
ADUC814 制造商:AD 制造商全称:Analog Devices 功能描述:MicroConverter, Small Package 12-Bit ADC with Embedded Flash MCU
ADUC814_02 制造商:AD 制造商全称:Analog Devices 功能描述:MicroConverter, Small Package 12-Bit ADC with Embedded FLASH MCU