- 您现在的位置：买卖IC网 > PDF目录12014 > ADUC836BSZ (Analog Devices Inc)IC ADC DUAL 16BIT W/MCU 52-MQFP PDF资料下载
参数资料
| 型号： | ADUC836BSZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 64/80页 |
| 文件大小： | 0K |
| 描述： | IC ADC DUAL 16BIT W/MCU 52-MQFP |
| 产品培训模块： | Process Control |
| 标准包装： | 1 |
| 系列： | MicroConverter® ADuC8xx |
| 核心处理器： | 8052 |
| 芯体尺寸： | 8-位 |
| 速度： | 12.58MHz |
| 连通性： | EBI/EMI，I²C，SPI，UART/USART |
| 外围设备： | POR，PSM，PWM，温度传感器，WDT |
| 输入/输出数： | 34 |
| 程序存储器容量： | 62KB（62K x 8） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 4K x 8 |
| RAM 容量： | 2.25K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.7 V ~ 5.25 V |
| 数据转换器： | A/D 7x16b; D/A 1x12b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 52-QFP |
| 包装： | 托盘 |
| 产品目录页面： | 738 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页当前第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页
ADuC836
–66–
ADuC836
–67–
OTHER HARDWARE CONSIDERATIONS
In-Circuit Serial Download Access
Nearly all ADuC836 designs will want to take advantage of the
in-circuit reprogrammability of the chip. This is accomplished
by a connection to the ADuC836’s UART, which requires an
external RS-232 chip for level translation if downloading code
from a PC. Basic configuration of an RS-232 connection is illus-
trated in Figure 66 with a simple ADM3202 based circuit. If users
would rather not include an RS-232 chip onto the target board,
refer to the application note, uC006–A 4-Wire UART-to-PC Interface
available at www.analog.com/microconverter, for a simple (and
zero-cost-per-board) method of gaining in-circuit serial download
access to the ADuC836.
In addition to the basic UART connections, users will also need
a way to trigger the chip into Download mode.This is accom-
plished via a 1 k pull-down resistor that can be jumpered onto
the PSEN pin, as shown in Figure 66.To get the ADuC836 into
Download mode, simply connect this jumper and power-cycle the
device (or manually reset the device, if a manual reset button is
available), and it will be ready to receive a new program serially.
With the jumper removed, the device will power on in Normal
mode (and run the program) whenever power is cycled or RESET
is toggled.
Note that PSEN is normally an output (as described in the Exter-
nal Memory Interface section) and that it is sampled as an input
only on the falling edge of RESET (i.e., at power-up or upon an
external manual reset). Note also that if any external circuitry
unintentionally pulls PSEN low during power-up or reset events,
it could cause the chip to enter Download mode and therefore fail
to begin user code execution as it should.To prevent this, ensure
that no external signals are capable of pulling the PSEN pin low,
except for the external PSEN jumper itself.
Embedded Serial Port Debugger
From a hardware perspective, entry to Serial Port Debug mode is
identical to the serial download entry sequence described above.
In fact, both Serial Download and Serial Port Debug modes can
be thought of as essentially one mode of operation used in two
different ways.
Note that the serial port debugger is fully contained on the
ADuC836 device, (unlike ROM monitor type debuggers) and
therefore no external memory is needed to enable in-system
debug sessions.
Single-Pin Emulation Mode
Also built into the ADuC836 is a dedicated controller for single-pin
in-circuit emulation (ICE) using standard production ADuC836
devices. In this mode, emulation access is gained by connection to
a single pin, the EA pin. Normally, this pin is hard-wired either
high or low to select execution from internal or external program
memory space, as described earlier.To enable single-pin emu-
lation mode, however, users will need to pull the EA pin high
through a 1 k resistor, as shown in Figure 66.The emulator
will then connect to the 2-pin header also shown in Figure 66.
To be compatible with the standard connector that comes
with the single-pin emulator available from Accutron Limited
(www.accutron.com), use a 2-pin 0.1-inch pitch Friction Lock
header from Molex (www.molex.com) such as their part number
22-27-2021. Be sure to observe the polarity of this header. As
represented in Figure 66, when the Friction Lock tab is at the
right, the ground pin should be the lower of the two pins (when
viewed from the top).
REV. A
相关PDF资料 |
PDF描述 |
|---|---|
| ADUC841BSZ62-5 | IC ADC/DAC 12BIT W/MCU 52-MQFP |
| VJ1825Y103JBGAT4X | CAP CER 10000PF 1KV 5% X7R 1825 |
| SCRU-01 | CONN RCPT IP68 USB A PNL MNT |
| VJ1825Y153JBGAT4X | CAP CER 0.015UF 1KV 5% X7R 1825 |
| VJ1825Y223JBGAT4X | CAP CER 0.022UF 1KV 5% X7R 1825 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUC841 | 制造商:AD 制造商全称:Analog Devices 功能描述:MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU |
| ADUC841BCP32-5 | 制造商:Analog Devices 功能描述:MICROCONVERTER 1-CYCLE VERSION ADUC829 - Trays |
| ADUC841BCP62-3 | 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 62KB Flash 3V 56-Pin LFCSP EP 制造商:Rochester Electronics LLC 功能描述:8BIT CISC 62KB FLASH 20MHZ 3.3V 56LFCSP - Bulk |
| ADUC841BCP62-5 | 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 62KB Flash 5V 56-Pin LFCSP EP |
| ADUC841BCP8-3 | 制造商:Analog Devices 功能描述:MCU 8-bit ADuC8xx 8052 CISC 62KB Flash 3V 56-Pin LFCSP EP 制造商:Rochester Electronics LLC 功能描述:8BIT CISC 62KB FLASH 20MHZ 3.3V 56LFCSP - Bulk |
发布紧急采购，3分钟左右您将得到回复。