参数资料
| 型号： | ADV7180WBCPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 70/116页 |
| 文件大小： | 0K |
| 描述： | IC VIDEO DECODER SDTV 40LFCSP |
| 标准包装： | 1 |
| 类型： | 视频解码器 |
| 应用： | 数码相机，手机，便携式视频 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 40-LFCSP-VQ（6x6） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页当前第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页
Data Sheet
ADV7180
Rev. I | Page 57 of 116
VDP_TTXT_TYPE_MAN_ENABLE, Enable Manual
Selection of Teletext Type, Address 0x60[2], User Sub Map
Setting VDP_TTXT_TYPE_MAN_ENABLE to 0 (default), the
manual programming of the teletext type is disabled.
Setting VDP_TTXT_TYPE_MAN_ENABLE to 1, the manual
programming of the teletext type is enabled.
VDP_TTXT_TYPE_MAN[1:0], Specify the Teletext Type,
Address 0x60[1:0], User Sub Map
These bits specify the teletext type to be decoded. These bits are
functional only if VDP_TTXT_TYPE_MAN_ENABLE is set to 1.
Table 72. VDP_TTXT_TYPE_MAN Function
VDP_TTXT_
TYPE_MAN[1:0]
625/50 (PAL)
525/60 (NTSC)
00 (default)
Teletext-ITU-BT.653-
625/50-A
Reserved
01
Teletext-ITU-BT.653-
625/50-B (WST)
Teletext-ITU-BT.653-
525/60-B
10
Teletext-ITU-BT.653-
625/50-C
Teletext-ITU-BT.653-
525/60-C or EIA516
(NABTS)
11
Teletext-ITU-BT.653-
625/50-D
Teletext-ITU-BT.653-
525/60-D
VDP Ancillary Data Output
Reading the data back via I2C may not be feasible for VBI data
standards with high data rates (for example, teletext). An alternative
is to place the sliced data in a packet in the line blanking of the
digital output CCIR656 stream. This is available for all standards
sliced by the VDP module.
When data is sliced on a given line, the corresponding ancillary
data packet is placed immediately after the next EAV code that
occurs at the output (that is, data sliced from multiple lines are
not buffered up and then emitted in a burst). Note that, due to
the vertical delay through the comb filters, the line number on
which the packet is placed differs from the line number on
which the data was sliced.
The user can enable or disable the insertion of VDP results that
have been decoded into the 656 ancillary streams by using the
ADF_ENABLE bit.
ADF_ENABLE, Enable Ancillary Data Output Through
656 Stream, Address 0x62[7], User Sub Map
Setting ADF_ENABLE to 0 (default) disables the insertion of
VBI decoded data into the ancillary 656 stream.
Setting ADF_ENABLE to 1 enables the insertion of VBI
decoded data into the ancillary 656 stream.
The user may select the data identification word (DID) and the
secondary data identification word (SDID) through programming
the ADF_DID[4:0] and ADF_SDID[5:0] bits, respectively.
ADF_DID[4:0], User-Specified Data ID Word in Ancillary
Data, Address 0x62[4:0], User Sub Map
This bit selects the data ID word to be inserted into the ancillary
data stream with the data decoded by the VDP.
The default value of ADF_DID[4:0] is 10101.
ADF_SDID[5:0], User-Specified Secondary Data ID Word
in Ancillary Data, Address 0x63[5:0], User Sub Map
These bits select the secondary data ID word to be inserted in
the ancillary data stream with the data decoded by the VDP.
The default value of ADF_SDID[5:0] is 101010.
DUPLICATE_ADF, Enable Duplication/Spreading of
Ancillary Data over Y and C Buses, Address 0x63[7], User
Sub Map
This bit determines whether the ancillary data is duplicated over
both Y and C buses or if the data packets are spread between
the two channels.
When DUPLICATE_ADF to 0 (default) is set, the ancillary data
packet is spread across the Y and C data streams.
When DUPLICATE_ADF to 1 is set, the ancillary data packet is
duplicated on the Y and C data streams.
ADF_MODE[1:0], Determine the Ancillary Data Output
Mode, Address 0x62[6:5], User Sub Map
These bits determine whether the ancillary data output mode is
in byte mode or nibble mode.
Table 73. ADF_MODE
ADF_MODE[1:0]
Description
00 (default)
Nibble mode
01
Byte mode, no code restrictions
10
Byte mode, but 0x00 and 0xFF prevented
(0x00 replaced by 0x01, 0xFF replaced by 0xFE)
11
Reserved
相关PDF资料 |
PDF描述 |
|---|---|
| ADV7186BBCZ | IC VIDEO DECODER 196CSPBGA |
| ADV7441ABSTZ-5P | IC DECODER DIGITIZER 144LQFP |
| ADV7513BSWZ | IC TX HDMI 165MHZ 64LQFP |
| ADV7520BCPZ-80 | IC XMITTER HDMI/DVI CEC 64LFCSP |
| ADV7520NKBBCZ-80 | IC XMITTER HDMI/DVI LP 76CSPBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADV7180WBCPZ-REEL | 功能描述:IC VIDEO DECODER SDTV 40LFCSP RoHS:是 类别:集成电路 (IC) >> 线性 - 视频处理 系列:- 产品变化通告:Product Discontinuation 07/Mar/2011 标准包装:3,000 系列:OMNITUNE™ 类型:调谐器 应用:移动电话，手机，视频显示器 安装类型:表面贴装 封装/外壳:65-WFBGA 供应商设备封装:PG-WFSGA-65 包装:带卷 (TR) 其它名称:SP000365064 |
| ADV7180WBST48Z | 制造商:Analog Devices 功能描述: |
| ADV7180WBST48Z-RL | 功能描述:视频 IC 10-bit 4x Oversampling SDTV Decoder RoHS:否 制造商:Fairchild Semiconductor 工作电源电压:5 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-28 封装:Reel |
| ADV7180WBSTZ | 功能描述:视频 IC 10-bit 4x Oversampling SDTV Decoder RoHS:否 制造商:Fairchild Semiconductor 工作电源电压:5 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-28 封装:Reel |
| ADV7180WBSTZ-REEL | 功能描述:视频 IC 10-bit 4x Oversampling SDTV Decoder RoHS:否 制造商:Fairchild Semiconductor 工作电源电压:5 V 电源电流:80 mA 最大工作温度:+ 85 C 封装 / 箱体:TSSOP-28 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。