参数资料
型号: AFS-EVAL-KIT
厂商: Microsemi SoC
文件页数: 164/334页
文件大小: 0K
描述: KIT STARTER EVAL FUSION AFS600
标准包装: 1
系列: Fusion®
类型: FPGA
适用于相关产品: AFS600-FG256
所含物品: 板,DVD,电源,编程器
其它名称: 1100-1148
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页当前第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页第175页第176页第177页第178页第179页第180页第181页第182页第183页第184页第185页第186页第187页第188页第189页第190页第191页第192页第193页第194页第195页第196页第197页第198页第199页第200页第201页第202页第203页第204页第205页第206页第207页第208页第209页第210页第211页第212页第213页第214页第215页第216页第217页第218页第219页第220页第221页第222页第223页第224页第225页第226页第227页第228页第229页第230页第231页第232页第233页第234页第235页第236页第237页第238页第239页第240页第241页第242页第243页第244页第245页第246页第247页第248页第249页第250页第251页第252页第253页第254页第255页第256页第257页第258页第259页第260页第261页第262页第263页第264页第265页第266页第267页第268页第269页第270页第271页第272页第273页第274页第275页第276页第277页第278页第279页第280页第281页第282页第283页第284页第285页第286页第287页第288页第289页第290页第291页第292页第293页第294页第295页第296页第297页第298页第299页第300页第301页第302页第303页第304页第305页第306页第307页第308页第309页第310页第311页第312页第313页第314页第315页第316页第317页第318页第319页第320页第321页第322页第323页第324页第325页第326页第327页第328页第329页第330页第331页第332页第333页第334页
Device Architecture
2-230
Revision 4
TMS
Test Mode Select
The TMS pin controls the use of the IEEE1532 boundary scan pins (TCK, TDI, TDO, TRST). There is an
internal weak pull-up resistor on the TMS pin.
TRST
Boundary Scan Reset Pin
The TRST pin functions as an active low input to asynchronously initialize (or reset) the boundary scan
circuitry. There is an internal weak pull-up resistor on the TRST pin. If JTAG is not used, an external pull-
down resistor could be included to ensure the TAP is held in reset mode. The resistor values must be
chosen from Table 2-183 and must satisfy the parallel resistance value requirement. The values in
Table 2-183 correspond to the resistor recommended when a single device is used and to the equivalent
parallel resistor when multiple devices are connected via a JTAG chain.
In critical applications, an upset in the JTAG circuit could allow entering an undesired JTAG state. In such
cases, Microsemi recommends tying off TRST to GND through a resistor placed close to the FPGA pin.
Note that to operate at all VJTAG voltages, 500
to 1 k will satisfy the requirements.
Special Function Pins
NC
No Connect
This pin is not connected to circuitry within the device. These pins can be driven to any voltage or can be
left floating with no effect on the operation of the device.
DC
Don't Connect
This pin should not be connected to any signals on the PCB. These pins should be left unconnected.
NCAP
Negative Capacitor
Negative Capacitor is where the negative terminal of the charge pump capacitor is connected. A
capacitor, with a 2.2 F recommended value, is required to connect between PCAP and NCAP.
PCAP
Positive Capacitor
Positive Capacitor is where the positive terminal of the charge pump capacitor is connected. A capacitor,
with a 2.2 F recommended value, is required to connect between PCAP and NCAP.
PUB
Push Button
Push button is the connection for the external momentary switch used to turn on the 1.5 V voltage
regulator and can be floating if not used.
PTBASE
Pass Transistor Base
Pass Transistor Base is the control signal of the voltage regulator. This pin should be connected to the
base of the external pass transistor used with the 1.5 V internal voltage regulator and can be floating if
not used.
PTEM
Pass Transistor Emitter
Pass Transistor Emitter is the feedback input of the voltage regulator.
This pin should be connected to the emitter of the external pass transistor used with the 1.5 V internal
voltage regulator and can be floating if not used.
XTAL1
Crystal Oscillator Circuit Input
Input to crystal oscillator circuit. Pin for connecting external crystal, ceramic resonator, RC network, or
external clock input. When using an external crystal or ceramic oscillator, external capacitors are also
recommended (Please refer to the crystal oscillator manufacturer for proper capacitor value).
If using external RC network or clock input, XTAL1 should be used and XTAL2 left unconnected. In the
case where the Crystal Oscillator block is not used, the XTAL1 pin should be connected to GND and the
XTAL2 pin should be left floating.
相关PDF资料
PDF描述
ESM10DRYS CONN EDGECARD 20POS DIP .156 SLD
EMM11DRTN CONN EDGECARD 22POS DIP .156 SLD
AGL-ICICLE-KIT KIT EVAL FOR IGOO ICICLE
ECM25DCCN CONN EDGECARD 50POS R/A .156 SLD
DC1266A-A BOARD DELTA SIGMA ADC LTC2453
相关代理商/技术参数
参数描述
AFSIMG-4735101M-NP 制造商:Sumida Corporation 功能描述:Inductor (no Datasheet to get info) 制造商:SUMIDA ELECTRONICS 功能描述:Inductor (no Datasheet to get info)
AFSK-12A-70 制造商:MACOM 制造商全称:Tyco Electronics 功能描述:FLEXSRRIP PIN CONFIGURATIONS, GENERIC
AFSK-12B-70 制造商:MACOM 制造商全称:Tyco Electronics 功能描述:FLEXSRRIP PIN CONFIGURATIONS, GENERIC
AFSK-12C-70 制造商:MACOM 制造商全称:Tyco Electronics 功能描述:FLEXSRRIP PIN CONFIGURATIONS, GENERIC
AFSK-12D-70 制造商:MACOM 制造商全称:Tyco Electronics 功能描述:FLEXSRRIP PIN CONFIGURATIONS, GENERIC