参数资料
型号: AT32UC3L032-D3HT
厂商: Atmel
文件页数: 76/174页
文件大小: 0K
描述: MCU AVR32 32K FLASH 48TTLGA
产品培训模块: AVR® UC3 Introduction
标准包装: 2,450
系列: AVR®32 UC3 L
核心处理器: AVR
芯体尺寸: 32-位
速度: 50MHz
连通性: I²C,SPI,UART/USART
外围设备: 欠压检测/复位,DMA,POR,PWM,WDT
输入/输出数: 36
程序存储器容量: 32KB(32K x 8)
程序存储器类型: 闪存
RAM 容量: 16K x 8
电压 - 电源 (Vcc/Vdd): 1.62 V ~ 3.6 V
数据转换器: A/D 9x12b
振荡器型: 内部
工作温度: -40°C ~ 85°C
封装/外壳: 48-UFLGA
包装: 托盘
29
32099I–01/2012
AT32UC3L016/32/64
4.5.3
Supervisor Calls
The AVR32 instruction set provides a supervisor mode call instruction. The scall instruction is
designed so that privileged routines can be called from any context. This facilitates sharing of
code between different execution modes. The scall mechanism is designed so that a minimal
execution cycle overhead is experienced when performing supervisor routine calls from time-
critical event handlers.
The scall instruction behaves differently depending on which mode it is called from. The behav-
iour is detailed in the instruction set reference. In order to allow the scall routine to return to the
correct context, a return from supervisor call instruction, rets, is implemented. In the AVR32UC
CPU, scall and rets uses the system stack to store the return address and the status register.
4.5.4
Debug Requests
The AVR32 architecture defines a dedicated Debug mode. When a debug request is received by
the core, Debug mode is entered. Entry into Debug mode can be masked by the DM bit in the
status register. Upon entry into Debug mode, hardware sets the SR.D bit and jumps to the
Debug Exception handler. By default, Debug mode executes in the exception context, but with
dedicated Return Address Register and Return Status Register. These dedicated registers
remove the need for storing this data to the system stack, thereby improving debuggability. The
Mode bits in the Status Register can freely be manipulated in Debug mode, to observe registers
in all contexts, while retaining full privileges.
Debug mode is exited by executing the retd instruction. This returns to the previous context.
4.5.5
Entry Points for Events
Several different event handler entry points exist. In AVR32UC, the reset address is
0x80000000. This places the reset address in the boot flash memory area.
TLB miss exceptions and scall have a dedicated space relative to EVBA where their event han-
dler can be placed. This speeds up execution by removing the need for a jump instruction placed
at the program address jumped to by the event hardware. All other exceptions have a dedicated
event routine entry point located relative to EVBA. The handler routine address identifies the
exception source directly.
AVR32UC uses the ITLB and DTLB protection exceptions to signal a MPU protection violation.
ITLB and DTLB miss exceptions are used to signal that an access address did not map to any of
the entries in the MPU. TLB multiple hit exception indicates that an access address did map to
multiple TLB entries, signalling an error.
All interrupt requests have entry points located at an offset relative to EVBA. This autovector off-
set is specified by an interrupt controller. The programmer must make sure that none of the
autovector offsets interfere with the placement of other code. The autovector offset has 14
address bits, giving an offset of maximum 16384 bytes.
Special considerations should be made when loading EVBA with a pointer. Due to security con-
siderations, the event handlers should be located in non-writeable flash memory, or optionally in
a privileged memory protection region if an MPU is present.
If several events occur on the same instruction, they are handled in a prioritized way. The priority
ordering is presented in Table 4-4 on page 31. If events occur on several instructions at different
locations in the pipeline, the events on the oldest instruction are always handled before any
events on any younger instruction, even if the younger instruction has events of higher priority
相关PDF资料
PDF描述
221629-6 CONN TERMINATR PLUG BNC 93OHM AU
VE-23Y-IY-F3 CONVERTER MOD DC/DC 3.3V 33W
VJ1825Y184KBCAT4X CAP CER 0.18UF 200V 10% X7R 1825
VJ1825Y274KBCAT4X CAP CER 0.27UF 200V 10% X7R 1825
VE-23Y-IY-F2 CONVERTER MOD DC/DC 3.3V 33W
相关代理商/技术参数
参数描述
AT32UC3L032-D3UR 功能描述:32位微控制器 - MCU UC3L-32KB Flash RoHS:否 制造商:Texas Instruments 核心:C28x 处理器系列:TMS320F28x 数据总线宽度:32 bit 最大时钟频率:90 MHz 程序存储器大小:64 KB 数据 RAM 大小:26 KB 片上 ADC:Yes 工作电源电压:2.97 V to 3.63 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:LQFP-80 安装风格:SMD/SMT
AT32UC3L032-ZAUR 功能描述:32位微控制器 - MCU UC3L-32KB Flash 85C RoHS:否 制造商:Texas Instruments 核心:C28x 处理器系列:TMS320F28x 数据总线宽度:32 bit 最大时钟频率:90 MHz 程序存储器大小:64 KB 数据 RAM 大小:26 KB 片上 ADC:Yes 工作电源电压:2.97 V to 3.63 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:LQFP-80 安装风格:SMD/SMT
AT32UC3L032-ZAUT 功能描述:32位微控制器 - MCU UC3L-32KB Flash RoHS:否 制造商:Texas Instruments 核心:C28x 处理器系列:TMS320F28x 数据总线宽度:32 bit 最大时钟频率:90 MHz 程序存储器大小:64 KB 数据 RAM 大小:26 KB 片上 ADC:Yes 工作电源电压:2.97 V to 3.63 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:LQFP-80 安装风格:SMD/SMT
AT32UC3L064 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:32-bit Atmel AVR Microcontroller
AT32UC3L064_1 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:AVR32 32-bit Microcontroller