- 您现在的位置：买卖IC网 > PDF目录10965 > AT85C51SND3B1-7FTUL (Atmel)IC DECODER/ENCODER DGTL 100CBGA PDF资料下载
参数资料
| 型号： | AT85C51SND3B1-7FTUL |
| 厂商： | Atmel |
| 文件页数： | 82/119页 |
| 文件大小： | 0K |
| 描述： | IC DECODER/ENCODER DGTL 100CBGA |
| 标准包装： | 90 |
| 类型： | 音频编码器/解码器 |
| 应用： | 移动电话，手机，视频显示器 |
| 电压 - 电源，数字： | 1.65 V ~ 3.6 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 100-TFBGA |
| 供应商设备封装： | 100-CTBGA（9x9） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页当前第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页
65
AT85C51SND3B
7632D–MP3–01/07
Timers/Counters
The AT85C51SND3B derivatives implement 2 general-purpose, 16-bit Timers/Counters.
They are identified as Timer 0 and Timer 1, and can be independently configured to
operate in a variety of modes as a Timer or as an event Counter. When operating as a
Timer, the Timer/Counter runs for a programmed length of time, then issues an interrupt
request. When operating as a Counter, the Timer/Counter counts negative transitions
on an external pin. After a preset number of counts, the Counter issues an interrupt
request.
The various operating modes of each Timer/Counter are described in the following
sections.
Timer/Counter
Operations
For instance, a basic operation is Timer registers THx and TLx (x = 0, 1) connected in
cascade to form a 16-bit Timer. Setting the run control bit (TRx) in TCON register (see
Table 81) turns the Timer on by allowing the selected input to increment TLx. When TLx
overflows it increments THx; when THx overflows it sets the Timer overflow flag (TFx) in
TCON register. Setting the TRx does not clear the THx and TLx Timer registers. Timer
registers can be accessed to obtain the current count or to enter preset values. They
can be read at any time but TRx bit must be cleared to preset their values, otherwise,
the behavior of the Timer/Counter is unpredictable.
The C/Tx# control bit selects Timer operation or Counter operation by selecting the
divided-down peripheral clock or external pin Tx as the source for the counted signal.
TRx bit must be cleared when changing the mode of operation, otherwise the behavior
of the Timer/Counter is unpredictable.
For Timer operation (C/Tx# = 0), the Timer register counts the divided-down peripheral
clock. The Timer register is incremented once every peripheral cycle (6 peripheral clock
periods). The Timer clock rate is FPER/6, i.e., FOSC/12 in standard mode or FOSC/6 in X2
mode.
For Counter operation (C/Tx# = 1), the Timer register counts the negative transitions on
the Tx external input pin. The external input is sampled every peripheral cycles. When
the sample is high in one cycle and low in the next one, the Counter is incremented.
Since it takes 2 cycles (12 peripheral clock periods) to recognize a negative transition,
the maximum count rate is FPER/12, i.e., FOSC/24 in standard mode or FOSC/12 in X2
mode. There are no restrictions on the duty cycle of the external input signal, but to
ensure that a given level is sampled at least once before it changes, it should be held for
at least one full peripheral cycle.
Timer Clock Controller
As shown in Figure 31, the Timer 0 (FT0) and Timer 1 (FT1) clocks are derived from
either the peripheral clock (FPER) or the oscillator clock (FOSC) depending on the T0X2
and T1X2 bits in CKCON register. These clocks are issued from the Clock Controller
block as detailed in Section “Oscillator”, page 28. When T0X2 or T1X2 bit is set, the
Timer 0 or Timer 1 clock frequency is fixed and equal to the oscillator clock frequency
divided by 2. When cleared, the Timer clock frequency is equal to the oscillator clock fre-
quency divided by 2 in standard mode or to the oscillator clock frequency in X2 mode.
相关PDF资料 |
PDF描述 |
|---|---|
| JN1FS04FKK | CONN PLUG 4POS R/A W/SOCKET SLD |
| AD1970JSTZRL | IC ENCODER BTSC W/CODEC 48-LQFP |
| ADV7177KSZ | IC DAC VIDEO NTSC 3-CH 44MQFP |
| VI-24L-CU-S | CONVERTER MOD DC/DC 28V 200W |
| VI-24K-CU-S | CONVERTER MOD DC/DC 40V 200W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT85C51SND3B1N-DDV | 功能描述:音频 DSP Microcontroller RoHS:否 制造商:Texas Instruments 工作电源电压: 电源电流: 工作温度范围: 安装风格: 封装 / 箱体: 封装:Tube |
| AT85C51SND3B1N-RTTUL | 功能描述:音频 DSP Microcontroller RoHS:否 制造商:Texas Instruments 工作电源电压: 电源电流: 工作温度范围: 安装风格: 封装 / 箱体: 封装:Tube |
| AT85C51SND3B1-RTTUL | 功能描述:音频 DSP MP3/WMA USB2.0 w/o DAC+DC/DC RoHS:否 制造商:Texas Instruments 工作电源电压: 电源电流: 工作温度范围: 安装风格: 封装 / 箱体: 封装:Tube |
| AT85C51SND3B2-RTTUL | 功能描述:音频 DSP Microcontroller RoHS:否 制造商:Texas Instruments 工作电源电压: 电源电流: 工作温度范围: 安装风格: 封装 / 箱体: 封装:Tube |
| AT85C51SND3BX | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:MP3 Microcontrollers |
发布紧急采购，3分钟左右您将得到回复。