- 您现在的位置：买卖IC网 > PDF目录298892 > B80547RE061256 (INTEL CORP) 32-BIT, 2530 MHz, MICROPROCESSOR, PBGA775 PDF资料下载
参数资料
| 型号： | B80547RE061256 |
| 厂商： | INTEL CORP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 32-BIT, 2530 MHz, MICROPROCESSOR, PBGA775 |
| 封装： | FLIP CHIP, LGA-775 |
| 文件页数： | 73/94页 |
| 文件大小： | 2796K |
| 代理商： | B80547RE061256 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页当前第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页
Datasheet
75
Thermal Specifications and Design Considerations
expected to be so minor that it would be immeasurable. An under-designed thermal solution that is
not able to prevent excessive activation of the TCC in the anticipated ambient environment may
cause a noticeable performance loss, and in some cases may result in a T
C that exceeds the
specified maximum temperature and may affect the long-term reliability of the processor. In
addition, a thermal solution that is significantly under-designed may not be capable of cooling the
processor even when the TCC is active continuously. Refer to the Intel Pentium 4 Processor on
90 nm Process in the 775-Land LGA Package Thermal Design Guide for information on designing
a thermal solution.
The duty cycle for the TCC, when activated by the Thermal Monitor, is factory configured and
cannot be modified. The Thermal Monitor does not require any additional hardware, software
drivers, or interrupt handling routines.
5.2.2
Thermal Monitor 2
The Celeron D processor in the 775-land package also supports a power management capability
known as Thermal Monitor 2. This mechanism provides an efficient mechanism for limiting the
processor temperature by reducing power consumption within the processor.
When Thermal Monitor 2 is enabled, and a high temperature situation is detected, the enhanced
Thermal Control Circuit (TCC) will be activated. This enhanced TCC causes the processor to
adjust its operating frequency (bus multiplier) and input voltage (VID). This combination of
reduced frequency and VID results in a decrease in processor power consumption.
A processor enabled for Thermal Monitor 2 includes two operating points, each consisting of a
specific operating frequency and voltage. The first point represents the normal operating conditions
for the processor.
The second point consists of both a lower operating frequency and voltage. When the enhanced
TCC is activated, the processor automatically transitions to the new frequency. This transition
occurs very rapidly (on the order of 5
μs). During the frequency transition, the processor is unable
to service any bus requests, and consequently, all bus traffic is blocked. Edge-triggered interrupts
will be latched and kept pending until the processor resumes operation at the new frequency.
Once the new operating frequency is engaged, the processor will transition to the new core
operating voltage by issuing a new VID code to the voltage regulator. The voltage regulator must
support VID transitions to support Thermal Monitor 2. During the voltage change, it will be
necessary to transition through multiple VID codes to reach the target operating voltage. Each step
will be one VID table entry (i.e., 12.5 mV steps). The processor continues to execute instructions
during the voltage transition. Operation at this lower voltage reduces both the dynamic and leakage
power consumption of the processor, providing a reduction in power consumption at a minimum
performance impact.
Once the processor has sufficiently cooled and a minimum activation time has expired, the
operating frequency and voltage transition back to the normal system operating point. Transition of
the VID code will occur first, to insure proper operation once the processor reaches its normal
operating frequency. Refer to Figure 5-3 for an illustration of this ordering.
相关PDF资料 |
PDF描述 |
|---|---|
| B80547RE077256 | 32-BIT, 2930 MHz, MICROPROCESSOR, PBGA775 |
| BX80547RE2933C | 32-BIT, 2930 MHz, MICROPROCESSOR, PBGA775 |
| BX80547RE3330CN | 32-BIT, 3330 MHz, MICROPROCESSOR, CBGA775 |
| BX80547RE2533C | 32-BIT, 2530 MHz, MICROPROCESSOR, PBGA775 |
| BX80547RE2667C | 32-BIT, 2600 MHz, MICROPROCESSOR, PBGA775 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| B8055 | 功能描述:函数发生器与合成器 Function Generator 5MHz RoHS:否 制造商:Tektronix 频率:20 MHz 设备类型:Function Generators |
| B-80-6 | 制造商:Hozan Tool Industrial Co Ltd 功能描述: |
| B8062N | 制造商:Laird Technologies Inc 功能描述:WHIP,MC,1/2,806-899 MHZ |
| B8062NCO | 功能描述:ACCY MISC RC B8062N ANTENNA RoHS:是 类别:RF/IF 和 RFID >> RF配件 系列:* 标准包装:1 系列:* |
| B8063 | 制造商:Laird Technologies Inc 功能描述:WHIP,MC,5/8,806-866 MHZ |
发布紧急采购，3分钟左右您将得到回复。