参数资料
型号: BX80532KC3000D
厂商: INTEL CORP
元件分类: 微控制器/微处理器
英文描述: 3000 MHz, MICROPROCESSOR
文件页数: 17/129页
文件大小: 1640K
代理商: BX80532KC3000D
Intel Xeon Processor with 512 KB L2 Cache
Datasheet
113
be cleared once the SMBus master device first reads the status register then reads the slave ARA
unless the fault condition persists. Reading the Status Register alone or setting the mask bit within
the Configuration Register does not clear the interrupt.
7.4.8
SMBus Device Addressing
Of the addresses broadcast across the SMBus, the memory component claims those of the form
“1010XXXZb”. The “XXX” bits are defined by pullups and pulldowns on the system baseboard.
These address pins are pulled down weakly (10 K
) on the processor substrate to ensure that the
memory components are in a known state in systems which do not support the SMBus, or only
support a partial implementation. The “Z” bit is the read/write bit for the serial bus transaction.
The thermal sensor internally decodes one of three upper address patterns from the bus of the form
“0011XXXZb”, “1001XXXZb”, or “0101XXXZb”. The device’s addressing, as implemented, uses
the SM_TS_A[1:0] pins in either the HI, LO, or Hi-Z state. Therefore, the thermal sensor supports
nine unique addresses. To set either pin for the Hi-Z state, the pin must be left floating. As before,
the “Z” bit is the read/write bit for the serial transaction.
Note that addresses of the form “0000XXXXb” are Reserved and should not be generated by an
SMBus master. The thermal sensor samples and latches the SM_TS_A[1:0] signals at power-up
and at the starting point of every conversion. System designers should ensure that these signals are
at valid input levels before the thermal sensor powers up. This should be done by pulling the pins to
SM_VCC or VSS via a 1 K or smaller resistor, or leaving the pins floating to achieve the Hi-Z
state. If the designer desires to drive the SM_TS_A[1:0] pins with logic, the designer must ensure
that the pins are at input levels of 3.3V or 0V before SM_VCC begins to ramp. The system designer
must also ensure that their particular implementation does not add excessive capacitance to the
address inputs. Excess capacitance at the address inputs may cause address recognition problems.
Refer to the appropriate platform design guidelines document and the System Management Bus
Specification.
Figure 42 on page 104 shows a logical diagram of the pin connections. Table 56 and Table 57
describe the address pin connections and how they affect the addressing of the devices.
相关PDF资料
PDF描述
BU-65843F3-110 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CQFP80
BP83C51FA-1 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PDIP40
BU-61559D1-240S 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CQIP78
BU-61559D1-240 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CQIP78
BU-61559D1-290K 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CQIP78
相关代理商/技术参数
参数描述
BX80532KC3000H 制造商:Intel 功能描述:MPU XEON NETBURST 64-BIT 0.13UM 3GHZ - Boxed Product (Development Kits)
BX80532KE2000D 制造商:Intel 功能描述:MPU XEON PROCESSOR NETBURST 64-BIT 0.13UM 2GHZ - Boxed Product (Development Kits)
BX80532KE2000DU 制造商:Intel 功能描述:XEON 2.0GHZ 533FSB 1U - Boxed Product (Development Kits)
BX80532KE2400DSL73L 制造商:Intel 功能描述:
BX80532KE2400E 制造商:Intel 功能描述:MPU XEON PROCESSOR NETBURST 64-BIT 0.13UM 2.4GHZ - Boxed Product (Development Kits)