- 您现在的位置：买卖IC网 > PDF目录378591 > DS21Q58LN E1 Quad Transceiver PDF资料下载
参数资料
| 型号： | DS21Q58LN |
| 英文描述： | E1 Quad Transceiver |
| 中文描述： | 素E1通道收发器 |
| 文件页数： | 18/74页 |
| 文件大小： | 647K |
| 代理商： | DS21Q58LN |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页
DS21Q58 E1 Quad Transceiver
18 of 74
8.1 Power-Up Sequence
On power-up and after the supplies are stable, the DS21Q58 should be configured for operation by writing to all the
internal registers (this includes setting the test register to 00h) since the contents of the internal registers cannot be
predicted on power-up. The LIRST (CCR5.4) should be toggled from 0 to 1 to reset the line interface circuitry. (It
takes the device about 40ms to recover from the LIRST bit being toggled.) After the SYSCLK input is stable, the
ESR bits (CCR4.5 and CCR4.6) should be toggled from 0 to 1 (this step can be skipped if the elastic store is
disabled).
Register Name:
RCR
Register Description:
Receive Control Register
Register Address:
10 Hex
Bit #
7
6
5
4
Name
RSMF
RSM
RSIO
RESE
NAME
BIT
RSYNC Multiframe Function.
Only used if the RSYNC pin is programmed in the
multiframe mode (RCR.6 = 1).
0 = RSYNC outputs CAS multiframe boundaries.
1 = RSYNC outputs CRC4 multiframe boundaries.
RSYNC Mode Select
0 = frame mode (see the timing diagrams in Section
24.1
)
1 = multiframe mode (see the timing diagrams in Section
24.1
)
RSYNC I/O Select.
(Note: This bit must be set to 0 when RCR .4 = 0.)
0 = RSYNC is an output (depends on RCR.6)
1 = RSYNC is an input (only valid if elastic store enabled)
Receive Elastic Store Enable
0 = elastic store is bypassed
1 = elastic store is enabled
—
3
Unused.
Should be set = 0 for proper operation.
Frame Resync Criteria
0 = resync if FAS received in error three consecutive times
1 = resync if FAS or bit 2 of non-FAS is received in error three consecutive times
Sync Enable
0 = auto resync enabled
1 = auto resync disabled
Resync.
When toggled from low to high, a resync is initiated. Must be cleared and
set again for a subsequent resync.
3
—
2
1
0
FRC
SYNCE
RESYNC
FUNCTION
RSMF
7
RSM
6
RSIO
5
RESE
4
FRC
2
SYNCE
1
RESYNC
0
相关PDF资料 |
PDF描述 |
|---|---|
| DS21Q58 | Dallas Semiconductor |
| DS2227-70 | Flexible NV SRAM Stik |
| DS2227-100 | Flexible NV SRAM Stik |
| DS2227-120 | Flexible NV SRAM Stik |
| DS2227 | Flexible NV SRAM Stik |
相关代理商/技术参数 |
参数描述 |
|---|---|
| DS21Q58LN+ | 功能描述:网络控制器与处理器 IC Quad E1 Transceiver RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21Q59 | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:RELIABILITY REPORT FOR DS21Q59, REV A2 |
| DS21Q59DK | 功能描述:网络开发工具 DS21Q59 Dev Kit RoHS:否 制造商:Rabbit Semiconductor 产品:Development Kits 类型:Ethernet to Wi-Fi Bridges 工具用于评估:RCM6600W 数据速率:20 Mbps, 40 Mbps 接口类型:802.11 b/g, Ethernet 工作电源电压:3.3 V |
| DS21Q59L | 功能描述:网络控制器与处理器 IC Quad E1 Transceiver RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| DS21Q59L+ | 功能描述:网络控制器与处理器 IC Quad E1 Transceiver RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。